543625
62
Zoom out
Zoom in
Previous page
1/95
Next page
62
- ENGLISH
Settings
PROJECTOR SETUP menu
See
z
“Navigating through the menu”
(
Æ
page 39).
See
z
“MAIN MENU” and “SUB MENU”
(
Æ
page 40).
PROJECTOR ID
The projector has an ID number setting function that
helps the user to control two or more projectors either
simultaneously or separately with a single remote
control.
Press ▲▼ to select [PROJECTOR ID].1 )
Press ◄► to switch [PROJECTOR ID].2 )
The setting will change as follows each time
z
◄► is pressed.
ALL 1
6 2
Note
The ID number can be set to [ALL], or selected from [1]
z
to [6].
If the projectors are given ID numbers, their remote
z
controls must be assigned the same ID numbers,
respectively.
If the ID number of a projector is set to [ALL], it can be
z
controlled by the remote control or the PC with any ID
number.
If multiple projectors are used and some of them
have their IDs set to “ALL”, they cannot be controlled
separately from the projectors with other ID numbers.
For details on remote control ID setting, refer to “Setting
projector ID number to remote control” (
Æ
page 21).
INSTALLATION
A projection scheme can be chosen depending on
the installation of the projector. If the picture is shown
upside down or in reverse, change the projection
scheme.
Select the setting by displaying the on-screen
z
indications using buttons of the remote control or
the control panel on the main unit.
Press ▲▼ to select [INSTALLATION].1 )
Press ◄► to switch [INSTALLATION].2 )
The setting will change as follows each time
z
◄► is pressed.
FRONT/FLOOR FRONT/CEILING
REAR/CEILING REAR/FLOOR
FRONT/
FLOOR
Setting on a desk/oor and
projecting from front
FRONT/
CEILING
Mounting on the ceiling and
projecting from front
REAR/
FLOOR
Setting on a desk/oor and
projecting from rear
REAR/
CEILING
Mounting on the ceiling and
projecting from rear
COOLING CONDITION
You can control the fan speed for projecting
angle. When the projector is angled, [COOLING
CONDITION] setting must be set correctly. Failure to
observe this may result in malfunctions, or the life of
the lamp or the other components may be shortened.
Press ▲▼ to select [COOLING 1 )
CONDITION].
Press <ENTER> button.2 )
The [COOLING CONDITION] screen will be
z
displayed.
Press ▲▼ to select cooling condition.3 )
Press <ENTER> button.4 )
When the conrmation message is 5 )
displayed, select [OK] or [CANCEL].
CEILING
SETTING
30°
30°
VERTICAL DOWN
SETTING
30°
30°
VERTICAL UP
SETTING
FLOOR
SETTING
62


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DX500U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DX500U in the language / languages: English as an attachment in your email.

The manual is 10,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-DX500U

Panasonic PT-DX500U Additional guide - English - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info