543625
32
Zoom out
Zoom in
Previous page
1/95
Next page
Powering ON/OFF
32
- ENGLISH
Basic Operation
Powering up the projector
Connect the supplied power cable.1 )
(AC100-120 V 50-60 Hz)
Press the [ | ] marked side of the 2 )
MAIN POWER switch to turn on the
power.
The POWER indicator lamp on the projector will
ash in red. After a short period, the indicator will
illuminate and the projector will enter standby
mode.
Press POWER ON.3 )
[Power indicator] lamp illuminates in green and
soon the image is projected on the screen.
Note
If the projector is powered up at about 0 °C, a warm-up
z
period of approximately 5 minutes may be necessary to
start projection. <TEMP> indicator lamp lights up during
the warm-up period. When the warm-up is completed,
<TEMP> indicator lamp turns off and the image is
projected on the screen.
If the temperature of the operating environment is low
z
and warm-up takes more than 5 minutes, the projector
will judge that a problem has occurred and the power
will be turned off automatically. If this happens, increase
the temperature around the projector so that it is 0 °C or
higher, and then turn on the MAIN POWER switch and
the POWER ON ( | ) switch once more.
With [ECO] setting in [Standby mode] (
z
Æ
page 64), When
switch on the projector, projection will start about 10
seconds late.
If the lter is not installed, the power is turned off
z
automatically after 10 minutes.
If projection was stopped last time by using the DIRECT
z
POWER OFF function, it can be started by setting the
MAIN POWER switch to the “ I ” (ON) position.
When you power up the projector or switch the signal
z
input, a high-frequency driving noise may be heard. This
is not a failure.
Making adjustment and
selection
It is recommended that the images are projected
continuously for at least 30 minutes before the focus
is adjusted.
Turn the focus ring, roughly adjust 4 )
the focus of the lens. (
Æ
page 34)
Select and set the projection scheme 5 )
of [INSTALLATION] and [COOLING
CONDITION] settings in [PROJECTOR
SETUP] menu.
Select the input signal by pressing 6 )
<INPUT SELECT> button (<RGB1>,
<RGB2>, <HDMI>, <VIDEO>,
<S-VIDEO>).
Adjust the tilt of the main unit in front 7 )
and rear or right and left.
Press <SHIFT> button to adjust the 8 )
position of the projection.
Press <AUTO SETUP> button if the 9 )
input signal is RGB signal.
Zoom the lens so the image lls the 10)
screen.
Readjust the focus.11)
Readjust the zoom so that the image 12)
size ts in the screen.
2)1) 6) 5) 7)
4)3)
7)3)
4)
5)
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DX500U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DX500U in the language / languages: English as an attachment in your email.

The manual is 10,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-DX500U

Panasonic PT-DX500U Additional guide - English - 42 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info