598898
162
Zoom out
Zoom in
Previous page
1/190
Next page
Chapter 5Maintenance — Maintenance/replacement
162 - ENGLISH
How to replace the lamp unit
Attention
f When the projector is mounted on the ceiling, do not conduct work while your face is near the lamp unit.
f Use the same type of lamp unit for both lamps.
f Make sure to attach the lamp unit and the lamp unit cover securely.
f If the lamp unit is not installed properly, remove it and then push it in slowly. Pushing it in quickly or forcibly may break the connector.
Fig. 1
Fig. 2
Lamp unit cover
Lamp unit cover fixing screw
Lamp unit 2
Handles
Lamp unit 1
Lamp unit fixing screws
Fan power connector
1) Set the <MAIN POWER> switch to <OFF> and disconnect the power plug from the power outlet.
f Wait at least one hour and check if the lamp unit has cooled down.
2) Remove the lamp unit cover. (Fig. 1)
f Use a Phillips screwdriver to turn the lamp unit cover xing screw (x1) counterclockwise until it turns freely, and open the lamp unit
cover slowly in the direction of the arrow.
f Opening the lamp unit cover quickly may result in damage to the cover.
f If you loosen the lamp unit cover xing screw with the projector installed upward in the vertical direction, the lamp unit cover may open
on its weight and the lamp unit may be dropped off.
3) Remove the lamp unit. (Fig. 2)
f Use a Phillips screwdriver to turn the lamp unit xing screws (x2) counterclockwise until they turn freely, and then remove the lamp
unit.
f Hold the handles of the lamp unit and remove it straight.
4) Push in the new lamp unit while paying attention to the insertion position.
f If the lamp unit is not installed properly, remove it and then push it in slowly. Pushing it in quickly or forcibly may break the connector.
5) Use a Phillips screwdriver to firmly tighten the lamp unit fixing screws (x2 each).
f Make sure to attach the lamp unit securely.
6) Attach the lamp unit cover.
i) Close the lamp unit cover in Step 2) in the reverse order.
f Attach the lamp unit cover so that the connector of the lamp unit cover is inserted to the fan power connector securely.
ii) Use a Phillips screwdriver to firmly tighten the lamp unit fixing screw (x1).
f Make sure to attach the lamp unit cover securely.
Note
f When you replace the lamp unit with new one, the projector resets the runtime of the lamp unit automatically.
Air lter
When the dust remains after cleaning, the lter replacement timing has come.
The air lter for the replacement (TMZX5209) is the optional accessories (service part). To purchase the product, consult your dealer.
When replacing the lamp unit, replace the corresponding air lter.
One air lter is provided for the optional Replacement lamp unit (Model No.: ET-LAD120 (1 pc)) and the optional Replacement lamp unit
(for portrait mode) (Model No.: ET-LAD120P (1 pc)), and two air lters are provided for the optional Replacement lamp unit (Model No.:
ET-LAD120W (2 pcs)) and the optional Replacement lamp unit (for portrait mode) (Model No.: ET-LAD120PW (2 pcs)).
162


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DX100U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DX100U in the language / languages: English as an attachment in your email.

The manual is 21,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info