544151
55
Zoom out
Zoom in
Previous page
1/190
Next page
Chapter 3Basic Operations — Switching on/off the projector
ENGLISH - 55
Note
f While the power indicator <ON (G)/STANDBY (R)> is lit in orange, the fan is running to cool the projector.
f For about 75 seconds after the projector is switched off and the luminous lamp cooling is started, the lamp indicators do not light up even if
the power is switched on. After the power indicator <ON (G)/STANDBY (R)> lights in red, turn on the power again.
f The projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lit in red). Refer to “Power consumption”
(x page 183) for the power consumption.
f The power indicator <ON (G)/STANDBY (R)> will ash if the projector receives a remote control signal.
f The power indicator <ON (G)/STANDBY (R)> will ash slowly in green while the shutter is closed.
f If the power indicator <ON (G)/STANDBY (R)> is ashing in red, consult your dealer.
Switching on the projector
When using the optional projection lens, attach the projection lens before switching on the projector.
Remove the lens cover rst.
2)
4)
4)
3)
1)
1) Connect the power cord to the projector body.
2) Connect the power plug to an outlet.
f (AC 120 V - 240 V 50 Hz/60 Hz)
3) Press the <ON> side of the <MAIN POWER> switch to turn on the power.
f The power indicator <ON (G)/STANDBY (R)> will light in red, and the projector will enter the standby mode.
4) Press the power on <b> button.
f The power indicator <ON (G)/STANDBY (R)> lights in green and the image is soon projected on the screen.
Note
f If the projector is switched on at around 0 °C (32 °F), a warm-up period of approximately ve minutes may be necessary until an image is
displayed.
The temperature indicator <TEMP> lights during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP>
turns off and the projection starts. Refer to “When an indicator lights up” (x page 157) for the indicator status.
f If the operating environment temperature is low and warm-up takes more than ve minutes, the projector will judge that a problem has
occurred and the power will automatically be set to standby mode. If this happens, increase the operating environment temperature to 0 °C
(32 °F) or higher, turn off the main power, and then switch on the projector again.
f If the [PROJECTOR SETUP] menu [STANDBY MODE] is set to [ECO], it may take approx. 10 seconds longer before the projector starts
projecting after the power is turned on, compared with when [NORMAL] is set.
f If the <MAIN POWER> switch was set to <OFF> during projection to end the projection using the direct power off function last time, and the
<MAIN POWER> switch is set to <ON> with the power plug connected to the outlet, the power indicator <ON (G)/STANDBY (R)> will light in
green and the image will soon be projected on the screen.
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DW830EK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DW830EK in the language / languages: English as an attachment in your email.

The manual is 21,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info