598891
20
Zoom out
Zoom in
Previous page
1/129
Next page
About Your Projector
20
- ENGLISH
Preparation
Setting projector ID number
to remote control
Each projector can be assigned a unique ID number,
and the handheld remote’ s number must be set to
match the intended projector.
The ID number of the projector is set to “ALL” on
shipping, and use the ID ALL button of the remote
control when using only a single projector.
Press <ID SET> button, and the 1 )
projector (s) will display it’s current ID
number onscreen. Within 5 seconds,
use the numeric keys (0-9) to match
the Remote’s ID number with that of
the desired projector.
Attention
Do not press <ID SET> button accidentally or carelessly
z
because the ID number on the remote control can be set
even when no projector is around.
If you do not enter the 2 digits ID number within 5
z
seconds after <ID SET> button has been pressed, the ID
will remain at the number that was set before <ID SET>
button was pressed.
Your specied ID number is stored in the remote control
z
unit unless another one is specied later. However, the
stored ID will be erased if the batteries of the remote
control are left exhausted. When the batteries are
replaced, set the same ID number again.
The ID number can be set to “ALL” or from “1” to “64”.
z
Note
Refer to “PROJECTOR ID” of “PROJECTOR SETUP
z
menu” (
Æ
page 75).
Using a wired remote control
When multiple projectors are connected as part of the
system, connect to units with a M3 stereo mini jack
commercial cable to simultaneously control multiple
main units with a single remote control through the
REMOTE 1 IN/OUT terminal. It is effective to use the
wired remote control in the environment in which an
obstacle stands in the light path or where devices are
susceptible to outside light.
Attention
Use 2 core shielded cable of length of 15 m or less. If the
z
length of the cable exceeds 15 m (49' 2"), the shielding
of the cable may not be sufcient and the remote control
may not work.
Remote Control
Connect to the remote
control wired terminal
Connect to the
secondary projector
M3 stereo mini jack cable
(commercial)
Connection terminals
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DW8300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DW8300 in the language / languages: English as an attachment in your email.

The manual is 12,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info