548352
99
Zoom out
Zoom in
Previous page
1/108
Next page
Technical Information
ENGLISH - 99
Appendix
Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this
order. Add parameters according to the details of control.
(2 bytes)
2 ID characters (2 bytes)
Semicolon (1 byte)
Colon (1 byte)
3 command characters
(3 bytes)
Parameter (undefined length)
End (1 byte)
Start (1 byte)
ZZ, 01 to 64 and 0A to 0Z
ID designate
Attention
z
When a command is transmitted after the lamp turned on, there may be a delay in response or the command
may not be executed. Try sending any command after 60 seconds.
z
When transmitting multiple commands, be sure to wait until 0.5 seconds has elapsed after receiving the
response from the projector before sending the next command. When transmitting a command which does not
need a parameter,
a colon (:) is not necessary.
Note
z
If a command cannot be executed, a
ER401
response is sent from the projector to the computer.
z
If an invalid parameter is sent, a
ER402
response is sent from the projector to the computer.
z
ID transmission in RS-232C supports ZZ (ALL) and the 01 to 64 and 0A to 0Z groups.
z
If a command is sent with a specied ID, a response will be sent to the computer only in the following cases.
It matches the projector ID
ID setting is set to ALL and responding (ID ALL) is [ON]
ID setting is set to Group and responding (ID Group) is [ON]
z
STX and ETX are character codes. STX shown in hexadecimal is 02, and ETX shown in hexadecimal is 03.
Cable specications
<When connected to a computer> <When connected multiple projectors>
Projector
<SERIAL IN>
terminal
1 NC NC 1
Computer
(DTE specications)
Projector 1
(<SERIAL OUT>
terminal)
1 NC NC 1
Projector 2
(<SERIAL IN>
terminal)
2 2 2 2
3 3 3 3
4 NC NC 4 4 NC NC 4
5 5 5 5
6 NC NC 6 6 NC NC 6
7 7 7 7
8 8 8 8
9 NC NC 9 9 NC NC 9
Control commands
The following table lists the commands that can be used to control the projector using a a computer.
<Projector control command>
Command
Details Notes (Parameter)
PON POWER ON
To check if the power is on, use the
Power query
command.
POF STANDBY
QPW Power query 000 = Standby 001 = POWER ON
IIS Switch input modes
VID = VIDEO SVD = S-VIDEO RG1 = RGB1
RG2 = RGB2 DVI = DVI-D
QSL
Query for active
lamp selection
0 = DUAL 1 = SINGLE
*1
2 = LAMP1 3 = LAMP2
LPM Lamp mode 0 = DUAL 1 = SINGLE
*1
2 = Only LAMP1 is ON 3 = Only LAMP2 is ON
OLP Lamp power setting 0
= HIGH 1 = LOW
*1: Uses the lamp (LAMP1 or LAMP2) with shorter operating hours.
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DW730UK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DW730UK in the language / languages: English as an attachment in your email.

The manual is 12,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info