548352
20
Zoom out
Zoom in
Previous page
1/108
Next page
Using Remote control
20 - ENGLISH
Preparation
Using Remote control
Inserting and removing the
batteries
1) Open the cover.
(i)
(ii)
2) Insert the batteries and close the cover
(insert the
side rst).
z
When remove the batteries, perform the steps
in the reverse order.
Setting Remote control ID
numbers
When you use the system with multiple projectors,
you can operate all the projectors simultaneously or
each projector individually using single remote control,
if a unique ID number is assigned to each projector.
After setting the ID number of the projector, set same
ID number on the remote control.
The ID number of the projector is set to [ALL] by
the factory default. When using a single projector,
press the <ID ALL> button on the remote control.
How to set
1) Press the <ID SET> button on the
remote control.
2) Within ve seconds, press the two-
digit ID number set on the projector
using the number (<0> - <9>) button.
Attention
z
Since setting of the ID number on the remote
control can be performed even without the projector,
do not press the <ID SET> button carelessly. If the
number (<0> - <9>) button is not pressed within ve
seconds after the <ID SET> button is pressed, the
ID number returns to that before pressing the <ID
SET> button.
z
The ID number set on the remote control will
be stored unless it is set again. However, it will
be erased if the remote control is left with dead
batteries. Set the same ID number again when the
batteries are replaced.
Note
z
Set the ID number of the projector from the
[PROJECTOR SETUP] menu
[PROJECTOR ID]
(
page 61).
Connecting to the projector
with a cable
When you use the system with multiple projectors,
congure the units as in the following gure. Use a
commercial M3 stereo mini jack cable and connect
the other devices to the <REMOTE 1 IN>/<REMOTE
1 OUT> terminals of the projector.
It is effective to use the remote control in a place
where an obstacle stands in the light path or where
devices are susceptible to the outside light.
Connecting terminals
Connect to the
secondary projector
M3 stereo mini jack cable
(commercial)
Remote
control
Connect to the remote control
wired terminal
Attention
z
Use a cable that is 15 m or shorter, with 2 core
shield. The remote control may not operate when
the length of the cable exceeds 15 m or when the
shielding of the cable is inadequate.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DW730UK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DW730UK in the language / languages: English as an attachment in your email.

The manual is 12,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info