598890
100
Zoom out
Zoom in
Previous page
1/129
Next page
NETWORK menu
100
- ENGLISH
Settings
Error information page
J
When “Error (Detail)” is displayed on the status information screen, click it to display the error details.
Depending on the nature of the error, the projector may be placed in the standby mode for its own
z
protection.
When [FAILED] has appeared for an item
Q
Parameter Description
MAIN CPU BUS Trouble has occurred in the microcomputer circuitry. Consult your dealer.
FAN Trouble has occurred in the fan or its drive circuit. Consult your dealer.
INPUT AIR TEMPERATURE
The input air temperature is too high. It may be that the projector is being used in an
operating environment where the temperature is high such as near a heating appliance.
OPTICS MODULE TEMPERATURE
The temperature inside the projector is high. It may be that the projector is being used
in an operating environment where the temperature is high such as near a heating
appliance.
AROUND LAMP TEMPERATURE
The temperature around the lamp is too high. It may be that the projector’s ventilation
holes are blocked.
LAMP1 REMAIN TIME
The lamp runtime has exceeded the prescribed cumulative time, and it is now time to
replace the lamp.
LAMP2 REMAIN TIME
LAMP1 STATUS
The lamp has failed to light.
Wait a short while for the lamp to cool off, and then turn on the power.
LAMP2 STATUS
APERTURE (CONTRAST-SHUTTER) Trouble has occurred in the contrast shutter circuitry. Consult your dealer.
INPUT AIR TEMP. SENSOR
Trouble has occurred in the sensor used to detect the input air temperature.
Consult your dealer.
OPTICS MODULE TEMP. SENSOR
Trouble has occurred in the temperature detection sensor inside the projector.
Consult your dealer.
AROUND LAMP TEMP. SENSOR
Trouble has occurred in the sensor used to detect the exhaust air temperature.
Consult your dealer.
BATTERY The backup battery has been run out. Consult your dealer.
AIRFLOW SENSOR
Trouble has occurred in the sensor used to detect the airow volume.
Consult your dealer.
COVER OPEN The lamp unit cover is not attached securely. Check the lamp unit compartment.
ACF UNIT The air cleaning lter (ACF) is not installed or trouble has occurred. (
Æ
109 page)
FILTER REMAIN The lter remaining is getting less. (
Æ
108 page)
BRIGHTNESS SENSOR
Trouble has occurred in the brightness sensor. If the problem cannot be corrected by
turning the power off and on, consult your dealer.
AC POWER
AC power supply voltage input has dropped. Check that there is sufcient
electrical wiring capacity for the projector’s power consumption requirements.
Note
The ACCESS ERROR INFORMATLION/ACCESS INFORMATION displays the past several thousand accesses/requests.
z
If many accesses/requests are made at a time, some of them may not be found in the information.
Check the ACCESS ERROR INFORMATION/ACCESS INFORMATION regularly.
z
OK: Normal operation
FAILED: Occurrence of trouble
100


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DS8500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DS8500 in the language / languages: English as an attachment in your email.

The manual is 12,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info