598890
60
Zoom out
Zoom in
Previous page
1/129
Next page
POSITION menu
60
- ENGLISH
Settings
Press ▲▼ to select [INTERLOCKED].3 )
Press ◄► to switch [INTERLOCKED].4 )
OFF
The [VERTICAL] and
[HORIZONTAL] settings are used
as the vertical and horizontal zoom
ratios respectively.
ON
The zoom ratio is set to the [BOTH]
setting.
This allows the pictures to be
zoomed at equal vertical and
horizontal ratios.
Note
When [ASPECT] is set to [THROUGH], [ZOOM] will not
z
appear.
When other than [DEFAULT] is selected for [ASPECT],
z
the [MODE] selection setting will not appear.
CLOCK PHASE
Clock phase adjustment achieves the best image
when the screen ickers or halos are observed around
contours.
Press ▲▼ to select [CLOCK PHASE].1 )
Press ◄► or <ENTER> button.2 )
The [CLOCK PHASE] individual adjustment
z
screen will be displayed.
Press ◄► to adjust the level.3 )
The value changes from 0 to 63. Adjust so that
z
the amount of interference is at a minimum.
Note
The CLOCK PHASE may not be adjusted, depending on
z
the signal.
No optimal value may be obtained if the output of the PC
z
to which the signal input is applied is unstable.
No optimal value may be obtained if the total number of
z
dots is not correct.
The [CLOCK PHASE] can be adjusted only when RGB
z
signal input is applied with RGB1 and RGB2 IN.
GEOMETRY
(PT-DZ8700U/PT-DS8500U only)
Square video can be projected onto a special shaped
screen using unique image processing technology.
Press ▲▼ to select [GEOMETRY].1 )
Press ◄► to switch [GEOMETRY].2 )
The setting will change as follows each time
z
◄► is pressed.
OFF KEYSTONE
PC CURVED
OFF
Geometry correction is not
performed.
KEYSTONE
This adjusts projected images when
they are distorted to a trapezoid.
CURVED
This adjusts projected images
when they are distorted to a curved
surface.
PC
Û
This is for performing geometry
correction from a computer.
GEOMETRY adjustment should be carried out by :
Û
a person who is familiar with the projector or by
a service person because a high level of skill is
required to make successful adjustment.
Select [KEYSTONE] or [CURVED] in 3 )
Step 2), and press <ENTER> button.
The [GEOMETRY : KEYSTONE] or
z
[GEOMETRY : CURVED] screen will be
displayed.
Press ▲▼ to select the desired 4 )
adjustment item, and press ◄► to
adjust the correction amount.
You can adjust the projection images as shown
z
below.
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DS8500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DS8500 in the language / languages: English as an attachment in your email.

The manual is 12,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info