598881
75
Zoom out
Zoom in
Previous page
1/223
Next page
Chapter 3Basic Operations — Operating with the remote control
ENGLISH - 75
Using the AC voltage monitor function
The value of input supply voltage can be displayed on the self-diagnosis display at the side of the projector.
r To display during projection
1) Press the power on <b> button.
f The value of the input supply voltage is displayed only as numeric value on the self-diagnosis display.
f The display will turn off automatically after approximately 3 seconds.
r To display during standby mode
1) Press the power standby <v> button.
f The value of the input supply voltage is displayed only as numeric value on the self-diagnosis display.
f The display will turn off automatically after approximately 3 seconds.
Note
f It can be set using the [PROJECTOR SETUP] menu [AC VOLTAGE MONITOR] (x page 138).
f The value of input supply voltage cannot be displayed in the self-diagnosis display during standby mode when the [PROJECTOR SETUP]
menu [STANDBY MODE] (x page 133) is set to [ECO].
f Operation can also be performed by the power on <b> button or power standby <v> button on the control panel.
Setting ID number of the remote control
When you use the system with multiple projectors, you can operate all the projectors simultaneously or each
projector individually using single remote control, if a unique ID number is assigned to each projector.
After setting the ID number of the projector, set same ID number on the remote control.
The factory default ID number of the projector is set to [ALL]. When using a single projector, press the <ID
ALL> button on the remote control. Also, you can control a projector by pressing the <ID ALL> button on
the remote control even if you do not know the projector ID.
button
1) Press the <ID SET> button on the remote control.
2) Within five seconds, press and set the one-digit or two-digit ID number set on the projector body
using the number (<0> - <9>) buttons.
f If you press the <ID ALL> button, you can control the projectors regardless of the ID number setting of the
projector body.
Attention
f Since the ID number of the remote control can be set without the projector body, do not press the <ID SET> button on the remote control
carelessly. If the <ID SET> button is pressed and no number (<0> - <9>) buttons are pressed within ve seconds, the ID number returns to
its original value before the <ID SET> button was pressed.
f The ID number set on the remote control will be stored unless it is set again. However, it will be erased if the remote control is left with dead
batteries. Set the same ID number again when the batteries are replaced.
Note
f When the ID number of the remote control is set to [0], you can control the projector regardless of the ID number setting of the projector
body, as same as when [ALL] is set.
f Set the ID number of the projector body from the [PROJECTOR SETUP] menu [PROJECTOR ID].
75


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DS20K2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DS20K2 in the language / languages: English as an attachment in your email.

The manual is 22,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-DS20K2

Panasonic PT-DS20K2 User Manual - German - 228 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info