598881
59
Zoom out
Zoom in
Previous page
1/223
Next page
Chapter 3Basic Operations — Switching on/off the projector
ENGLISH - 59
Note
f While the power indicator <ON (G)/STANDBY (R)> lights in orange, the fan is running to cool the projector.
f For about 150 seconds after the projector is switched off and the luminous lamp cooling is started, the lamp indicators do not light up even if
the power is switched on. After the power indicator <ON (G)/STANDBY (R)> lights in red, turn on the power again.
f The projector consumes power even in standby mode (power indicator <ON (G)/STANDBY (R)> lit in red). Refer to “Power consumption”
(x page 215) for the power consumption.
f When the projector receives the signal from the remote control, the power indicator <ON (G)/STANDBY (R)> will blink in the following color
according to the status of the projector.
g When the projector is in projection mode: Green
g When the projector is in standby mode: Orange
However, if the [PROJECTOR SETUP] menu [STANDBY MODE] is set to [ECO], the indicator will stay lit in red and will not blink if the
projector is in standby mode.
f The power indicator <ON (G)/STANDBY (R)> will blink slowly in green while the shutter function is in use (shutter: closed).
f If the power indicator <ON (G)/STANDBY (R)> is blinking in red, consult your dealer.
Switching on the projector
Install the projection lens before switching on the projector.
Remove the lens cover rst.
2)
4)
4)
3)
1)
1) Connect the power cord to the projector.
2) Connect the power plug to an outlet.
f (AC 200 V - 240 V 50 Hz/60 Hz)
3) Press the <ON> side of the <MAIN POWER> switch to turn on the power.
f The power indicator <ON (G)/STANDBY (R)> lights in red, and the projector enters the standby mode.
4) Press the power on <b> button.
f The power indicator <ON (G)/STANDBY (R)> lights in green and the image is soon projected on the screen.
Attention
f Using the projector while the lens cover is attached may cause the device to heat up and result in a re.
Note
f If the projector is switched on at around 0 °C (32 °F), a warm-up period of up to ve minutes (PT-DZ16K2: up to 20 minutes) may be
necessary until an image is displayed.
The temperature indicator <TEMP> lights during the warm-up period. When the warm-up is completed, the temperature indicator <TEMP>
turns off and the projection starts. Refer to “When an indicator lights up” (x page 179) for the indicator status display.
f If the operating environment temperature is low and a warm-up takes more than ve minutes (PT-DZ16K2: 20 minutes), the projector
will judge that a problem has occurred and the power will automatically be set to standby mode. If this happens, increase the operating
environment temperature to 0 °C (32 °F) or higher, turn off the main power, and then turn on the power again.
f If the [PROJECTOR SETUP] menu [STANDBY MODE] is set to [ECO], it may take approx. 10 seconds longer before the projector starts
projecting after the power is turned on, compared with when [NORMAL] is set.
f When the [PROJECTOR SETUP] menu [INITIAL STARTUP] is set to [LAST MEMORY], and the power was turned off at the previous
use by pressing the <OFF> side of the <MAIN POWER> switch while projecting or with the power breaker, the power indicator <ON (G)/
STANDBY (R)> will light up in green and the image is projected after a while when the power is turned on by pressing <ON> side of the
<MAIN POWER> switch while the power plug is plugged into the outlet, or when the power breaker is turned on.
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-DS20K2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-DS20K2 in the language / languages: English as an attachment in your email.

The manual is 22,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic PT-DS20K2

Panasonic PT-DS20K2 User Manual - German - 228 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info