542439
64
Zoom out
Zoom in
Previous page
1/81
Next page
Replacement
64
- ENGLISH
Maintenance
J
Lamp unit
The lamp unit is a consumable component. You can check the total usage time using Lamp runtime in the
Information menu on page 60.
It is recommended to ask an authorized engineer to replace the lamp unit. Contact your dealer.
Consult your dealer to purchase a replacement lamp unit (ET-LAC100).
CAUTION:
■ Do not replace the lamp unit when it is hot. (Wait at least 1 hour after use.)
The inside of the cover can become very hot, take care to avoid burn injuries.
Notes on the replacement of the lamp unit
J
The luminous source of the lamp is made of glass and may burst if you hit it against a hard surface or drop
z
it.
Please handle with care.
A Phillips screwdriver is required for replacement of the lamp unit.
z
When replacing the lamp unit, be sure to hold it by the handle.
z
When replacing the lamp because it has stopped illuminating, there
z
is a possibility that the lamp may be broken. If replacing the lamp of a
projector which has been installed on the ceiling, you should always
assume that the lamp is broken, and you should stand to the side
of the lamp cover, not underneath it. Open the lamp cover gently.
Small pieces of glass may fall out when the lamp cover is opened.
If pieces of glass get into your eyes or mouth, seek medical advice
immediately.
The lamp contains mercury. Consult your local municipality or your
z
dealer about correct disposal of used lamp units.
Attention
Do not use other than designated lamp units.
z
The part numbers of accessories and separately sold components are subject to change without notice.
z
When to replace the lamp unit
J
The lamp unit is a consumable component. Brightness decreases according to duration of usage, so
periodical replacement of the lamp unit is necessary.
When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the
screen and <LAMP> indicator lights yellow. Replace the lamp with a new one promptly.
Lamp runtime
On screen
Lamp replacement icon
LAMP indicator
Over 2 000 hours
The message is displayed for 4 seconds. If you
press any button within the 4 seconds, the message
disappears.
Lights in yellow (even in
stand-by mode).
*
2 000 hours of use is a rough guideline, but is not a guarantee. The lamp runtime differs depending on the
setting of "Lamp power" menu.
Note
The Lamp replacement icon will not appear when the [Display] function is set to [Off] (
z
Æ
page 54), or during
"Freeze" (
Æ
page 34), or "AV mute" (
Æ
page 35).
64


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic PT-CW230EA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic PT-CW230EA in the language / languages: English as an attachment in your email.

The manual is 7,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info