627465
37
Zoom out
Zoom in
Previous page
1/52
Next page
Others
-37-
£: Red Eye Reduction -20-
ª
To Change the Counter Display Mode
By changing [C.DISPLAY] on the [DISPLAY SETUP]
Sub-Menu, you can change the Counter Display Mode to
Tape Counter Indication [COUNTER] (0:00.00), Memory
Counter Indication [MEMORY] (M0:00.00), and Time Code
Indication [TIMECODE] (0h00m00s00f). (
-10-
) By repeatedly
pressing the [COUNTER] Button on the Remote Controller,
you can change the Counter Display Mode.
ª
To Display Date/Time Indication
To display Date/Time Indication, set the appropriate Date/
Time in [DATE/TIME] on the [DISPLAY SETUP] Sub-Menu.
(
-10-
)
You can also press the [DATE/TIME] Button of the Remote
Controller repeatedly to display or change the Date/Time
Indication.
ª
To Change the Display Mode
By changing [DISPLAY] on the [DISPLAY SETUP]
Sub-Menu, you can change the Display Mode to All Function
Display [ALL], Partial Display [PARTIAL] and Minimum
Display [OFF].
Owner ID
You can register your name and address in your Movie
Camera to identify the owner.
1
Set [CAMERA FUNCTIONS] >> [OTHER FUNCTIONS]
>> [OWNER ID SET] >> [YES].
The [OWNER ID] Menu appears.
2
Turn the [PUSH] Dial
(21)
to select [PIN NUMBER] and
press the [PUSH] Dial
(21)
to input desired numbers.
3
Turn the [PUSH] Dial
(21)
to select numbers and press
the [PUSH] Dial
(21)
to enter them.
You can input 4 digits.
4
Press the [] Button.
5
Repeat Steps 24 to input desired characters for
[NAME]/[HOUSE No.]/[POSTCODE].
You can input up to 12 characters in [NAME], and up to
11 characters in [HOUSE No.] and [POSTCODE].
6
Press the [] Button to finish the setup.
To verify Owner ID
Keep pressing the [;] Button for approximately 5 seconds.
To Check Owner ID
If Owner ID has already been set, carrying out Step 1 above
will display [INPUT PIN NUMBER] on the screen. Input the
Pin Number you have already selected. If the number is not
correct, the screen will not change. If the number is correct,
the contents of the setup will be displayed. (By repeating
Steps 2 to 4 above, you can change the contents.)
Warning/Alarm Indications
If any one of the following indications lights up or flashes,
please check the condition of the Movie Camera.
3: Condensation has occurred.
-43-
Y: The accidental erasure prevention slider on the
inserted Cassette is open (that is, set to [SAVE]).
You are about to do audio dubbing on the unrecorded
(blank) portion of the tape.
No Cassette is inserted.
-9-
6: The Battery is low. Recharge it. -7-
0: The built-in battery is low. -13-
:: The video heads are dirty. -43-
2END:
The tape came to end during recording.
REMOTE:
Wrong Remote Controller Mode has been selected.
-7-
UNPLAYABLE TAPE
(OTHER FORMAT):
You are attempting to play back a tape section that has
been recorded with a different TV system.
UNABLE TO A. DUB
(LP RECORDED):
Because the original recording was done in LP Mode,
audio dubbing cannot be performed.
INCOMPATIBLE TAPE:
This Cassette is incompatible.
PLEASE RE-OPERATE
AFTER PUSHING
RESET BUTTON:
Mechanism Irregular is detected. Press the [RESET]
Button (
-5-
). This may solve the problem.
TO SERVICE:
It is a malfunction.
CARD FULL:
Card does not have sufficient memory remaining.
Select Card Mode and delete unnecessary files.
NO CARD:
Card is not inserted.
NO FILE:
Card has no files recorded on it.
UNPLAYABLE CARD:
You are attempting to play back a data which is not
compatible with this Movie Camera.
CARD ERROR:
This Card is not compatible with this Movie Camera.
COPY INHIBITED:
Because the medium is protected by a copy guard,
images cannot be recorded correctly.
INCORRECT
OPERATION:
You are attempting to record to a tape in VCR Mode.
The [TAPE/CARD/CARD MODE] Selector is set to
[MPEG4] or [VOICE] when [PHOTO SHOT] Button is
pressed.
You are attempting to record to a tape in Card Mode.
Notes and Hints
ª
Concerning the Power Supply
When the Movie Camera is used for a long time, the
Camera body becomes warm, but this is not a malfunction.
If the [CHARGE] Lamp does not light up although the
Battery is attached to the AC Adaptor, detach the Battery
and reattach it.
Battery CGP-D110 and CGP-D105 cannot be charged with
this AC Adaptor.
ª
Inserting/Removing the Cassette
In the case of using a previously recorded Cassette, you
can use the Camera Search Function to find the position
where you want to continue recording.
If a new Cassette is inserted, rewind to the beginning of the
tape before starting recording.
When inserting the cassette, make sure it faces in the right
direction and then push it in until it stops.
ª
Alarm Sounds
When [BEEP SOUND] on the [OTHER FUNCTIONS]
Sub-Menu on the [CAMERA FUNCTIONS] Main-Menu is set
to [ON], confirmation/alarm beeps are issued as follows.
1 Beep
When you start recording
When you switch the [OFF/ON/MODE] Switch from [OFF]
to [ON]
2 Beeps
When you pause recording
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic NVGX7B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic NVGX7B in the language / languages: English as an attachment in your email.

The manual is 5,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info