627419
10
Zoom out
Zoom in
Previous page
1/52
Next page
Before using
10
LSQT1006
ª How to turn the power on and off with
the LCD monitor/viewfinder
When the power switch is set to [ON], the power
can be turned on and off with the LCD monitor
and the viewfinder when the unit is in Tape
Recording Mode.
1 Open the LCD monitor out or extend the
viewfinder to use. (
-11-)
The LCD monitor or the viewfinder will be
activated.
2 Close the LCD monitor and retract the
viewfinder.
The power will not turn off unless the LCD
monitor is closed and the viewfinder is
retracted.
The status indicator automatically goes off
and the power turns off. (If quick start is set to
[ON] (
-12-), the unit goes into quick start
standby mode and the status indicator lights
green.)
The power does not turn off even if the LCD
monitor is closed and the viewfinder is
retracted while recording on a tape.
3 Open the LCD monitor or extend the
viewfinder to turn the power on and use the
movie camera again.
The status indicator lights up and the power
turns on.
Setting date and time
When the movie camera is turned on for the first
time, [SET DATE AND TIME] will appear.
Select [YES] and press the centre of the
joystick. Do steps 2 and 3 below to set the date/
time.
If the screen shows the incorrect date/time, then
adjust it.
Set to Tape Recording Mode.
1 Set [BASIC] >> [CLOCK SET] >> [YES]. (-16-)
2 Move the joystick left or right in order to
select the item to be set. Then move the
joystick up or down to set the desired value.
The year will change as follows:
2000, 2001, ..., 2089, 2000, ...
The 24-hour clock is used.
3 Press the joystick to determine the setting.
The clock function starts at [00] seconds.
ª
About date/time
The date and time function are driven by a
built-in lithium battery.
Make sure to check the time before recording
because the built-in clock is not very accurate.
ª
Recharging the built-in lithium battery
If [0] or [--] is appears when the camera is
turned on, then the built-in lithium battery has
run down. Use the steps below to charge the
battery. When turn on the power for the first time
after charging, [SET DATE AND TIME] will
appear. Select [YES] and set the date and time.
Connect the AC adaptor to the camera or attach
the battery to the camera, and the built-in lithium
battery will be recharged. Leave the camera as
is for approx. 24 hours, and the battery will drive
the date and time for approx. 6 months. (Even if
the [OFF/ON] switch is set to [OFF], the battery
is still being recharged.)
OFF
ON
OFF
ON
OFF
ON
LSQT1006ENG.book 10 ページ 2005年12月9日 金曜日 午前11時17分
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic NVGS27EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic NVGS27EB in the language / languages: English as an attachment in your email.

The manual is 4,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic NVGS27EB

Panasonic NVGS27EB User Manual - English - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info