627364
11
Zoom out
Zoom in
Previous page
1/116
Next page
-11-
DEUTSCH
ENGLISH
Stromversorgung mit dem Akku
Vor dem Einsatz den Akku aufladen.
1 Den Akku waagerecht bis zum Anschlag auf
den Netzadapter aufschieben, wie oben
gezeigt.
2 Das Netzkabel an den Netzadapter und an eine
Netzsteckdose anschließen.
3 Wenn die Lampe [100%] am Netzadapter
leuchtet, ist der Ladevorgang beendet.
Wenn die Lampe [QUICK] leuchtet, hat der Akku eine
Ladung erreicht, die für ca. 1 Stunde ununterbrochene
Aufnahme ausreicht.
Die gedruckten Zahlen (80%, 100%) auf dem
Netzadapter zeigen den ungefähren erreichten
Ladezustand an.
Die Lampe [QUICK] blinkt und leuchtet nur beim Laden
eines Akkus vom Quick-Charge-Typ. Der mit diesem
Camerarecorder mitgelieferte Akku ist nicht vom Quick-
Charge-Typ.
Wenn das Gleichstrom-Eingangskabel am Netzadapter
angeschlossen ist, kann der Akku nicht aufgeladen werden.
4 Zum Abnehmen des Akkus diesen in
entgegengesetzter Richtung zum obigen
Schritt 1 schieben.
Auch das Netzkabel aus der Netzsteckdose ziehen.
5 Den Sucher bis zum Anschlag nach hinten
schieben und dann nach oben schwenken.
6 Den Akku in die Akkuhalterung am
Camerarecorder einsetzen und nach unten
schieben, bis er mit einem Klick einrastet.
Abnehmen des Akkus vom Camerarecorder
Die Taste [BATT. EJECT PUSH] 1 gedrückt halten und
gleichzeitig den Akku nach oben schieben und abnehmen.
Darauf achten, daß der Akku nicht aus Versehen fallen
gelassen wird.
Vor dem Abnehmen des Akkus den Schalter [POWER] auf
[OFF] stellen.
12 4
5
6
3
PUSH
1
1
80 100%
QUICK
Supplying Power with the Battery
Before use, charge the Battery.
1 Place the Battery on the AC Adaptor as shown
above and slide it horizontally until it stops.
2 Connect the AC Mains Lead to the AC Adaptor
and to an AC mains socket.
3 When the [100%] Lamp on the AC Adaptor is lit,
charging is finished.
When the [QUICK] Lamp is lit, approximately 1 hour of
continuous recording is possible.
The figures (80%, 100%) printed on the AC Adaptor
indicate approximate charge reached.
The [QUICK] Lamp flashes and then remains lit only when
charging a quick-charge type battery. The Battery supplied
with this Movie Camera is not of the quick-charge type.
Charging is not possible when the DC Input Lead is
connected to the AC Adaptor.
4 Remove the Battery by sliding it in the opposite
direction of Step 1 above.
Also disconnect the AC Mains Lead.
5 Slide the Finder backward to its fully extended
position and then tilt it upward.
6 Insert the Battery into the Battery Holder on the
Movie Camera and slide it downward until it
locks with a click.
Removing the Battery from the Movie Camera
While pressing the [BATT. EJECT PUSH] Button 1, slide the
Battery upward to remove it.
Be careful not to drop the Battery by accident.
Before removing the Battery, set the [POWER] Switch to
[OFF].
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic NVDS990EG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic NVDS990EG in the language / languages: English, German as an attachment in your email.

The manual is 5,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info