136817
6
Zoom out
Zoom in
Previous page
1/24
Next page
6
VCR Recording
n Switch on and set the TV to the video output channel and insert a cassette with an intact erasure prevention tab into the VCR.
n Before recording, select the channel with the |CH| button. Select the AV channel |INPUT SELECT AV| if you want to record
a programme from scart AV1, AV2, front input = A3 or Disc = dc.
n Switch the remote control to VCR .
n Press |REC| to start recording.
n Press Stop `` to stop recording.
n Use Pause to pause recording.
n Restart recording by pressing this button again. To preserve the video heads, the function will be switched off after 5 minutes.
Direct TV Recording
The |DIRECT TV REC| button allows you to immediately start recording the same programme that you are viewing on the
TV, if your TV is equipped with Q Link or with a similar function from other manufacturers (see page 3) and connected
with a fully-wired 21-pin scart lead (not supplied).
OTR Function (OTR = One Touch Recording)
n n
REC/OTR
To record for a specific length of time, press this button on the VCR. You can extend the recording time from
30, 60, 120, 180 to 240 minutes by pressing the button repeatedly.
The selected length of recording time will appear on the VCR display. To stop in advance press Stop `` .
If you want to watch another TV programme at the same time as you are recording, select the channel on the TV.
Tape Speed
n Press |DISPLAY| until [REMAIN] on the VCR display appears.
n Press |SP/LP/EP| before recording, in order to select the tape speed for the recording.
Make sure that the remaining time on the cassette is longer than the time set for recording,
otherwise the whole programme cannot be recorded.
The following information appears on the VCR display:
[SP] standard recording time: optimum picture quality.
[LP] double recording time: slightly reduced picture quality.
[EP] (SUPER LP) triple recording time: slightly reduced picture quality.
Note: Distorted pictures produced when playing back some cassettes (e.g. type E300) after LP or EP recordings are not functional faults.
VCR display
On Screen Display
VCR Display
RQTD0021-B
Pos
Name Date Start Stop PDC
1. - - - - - - -/- - - -:- - - -:- - - - - -
2. - - - - - - -/- - - -:- - - -:- - - - - -
3. - - - - - - -/- - - -:- - - -:- - - - - -
Panasonic VCR
Timer recording 1/2
Pos
Name Date Start Stop PDC
1.
***
32 Mo-Sa 13:30 14:00 LP ON
2.
***
32 20/9 15:00 16:00 SP OFF
3. - - - - - - -/- - - -:- - - -:- - - - - -
Panasonic VCR
Timer recording 1/2
Timer recording with On Screen Menu
With the On Screen Menu you can programme Timer recordings (up to 16 programmes).
Switch on and set the TV to the video output channel and insert a cassette with an intact erasure prevention tab into the VCR.
n Switch the remote control to VCR .
n Press |PROG/CHECK| to display [Timer recording] menu and press |ENTER|.
n Set the channel [Pos].
You can use the cursors
:;8 9
on the remote control to move around the menu, in order to make changes.
n Set the recording [Date], day or week.
For example: Sa means that the programme will be recorded every Saturday, or Mo - Sa means that the
programme will be recorded every day from Monday to Saturday.
n Set the [Start] time. If you keep this button pressed down
:;
, the time will change in 30 minute jumps.
n Set the [Stop] time.
n Set the Tape Speed [SP], [LP], [EP] or [A] (automatic).
n In the setting A (automatic), the VCR automatically switches (with a short picture distortion) from SP to the slow tape
speed LP, to record the programme as long as possible, if the remaining tape time is not long enough.
n The preset [PDC] settings can be manually changed.
[ON] The broadcaster provides PDC signals. If the program is starting earlier or later than planned
the timer recording will be synchronised to the actual broadcast start.
Important ! The time and date settings must be exactly same as programme information (programme magazine).
If there is a special PDC time noted, it must be used. (The recording can not start, if the settings are not exact.)
[- - -] The broadcaster does not provide PDC signals.
[OFF] The broadcaster providinges PDC signals, but the function is turned off. With this setting you have to
add to the start and stop time so that the whole film can be recorded completely, just in case the film is
broadcasted out of the planned time.
n To store the programme, press |ENTER|.
n In order to preset other recordings, repeat this procedure.
n Press |TIMER| to switch the VCR to Standby mode for Timer recording. Make sure that in the VCR display
i
appears.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic nv vhd1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic nv vhd1 in the language / languages: English as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic nv vhd1

Panasonic nv vhd1 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info