31098
25
Zoom out
Zoom in
Previous page
1/32
Next page
NV-HV61 Series (Hi-Fi)
NV-HV51 Series (Hi-Fi)
NV-MV21 Series (Mono)
NV-MV16 Series (Mono)
NV-SV121 Series (S-VHS, Hi-Fi)
PAL
VHS
625
Operating Instructions
.
SUPER LP 35x JET SEARCH
PULL OPEN
EJECT
TIMER REC
REC
CH
3D DNR
TBC
Super VHS
ET
Video Cassette Recorder
Contents Page
Included Accessories 2
Inserting Batteries
Safety Precautions 3
Front Panel VCR 4
Rear Panel VCR 5
Remote control functions 6- 7
Connecting with a 21-pin Scart cable 8
VCR Auto Setup with 21-pin Scart cable
Connecting with S-VIDEO cable 9
VCR Auto Setup with S-VIDEO cable
Connecting with RF Coaxial cable 10
VCR Auto Setup with RF Coaxial cable
Channel tuning / Correcting interferences 11
Setting Time and Date
External Devices
Connecting a Set Top Box, satellite receiver, 12
decoder or a second recorder
Connecting an amplifier, 13
Menu 14
Manual Setup
Creating a new station table 15
Changing the name and order of TV stations 16
Creating a new station table 17
Shipping condition/factory defaults
Menu Others 18-19
Recording 20
Timer recording 21-22
Recording with INTELLIGENT TIMER 23
Recording with ShowView 24
Recording with external recording controls 25
Playback 26
General convenient functions 27-28
NICAM sound system, NTSC playback 29
Before requesting service 30
Specifications 31
Index last page
Connecting to the AV3 input
Before connecting the device, operating it or adjusting settings please read these operating
instructions completely; especially the safety precautions on pages 2-3.
Matsushita Electric Industrial Co., Ltd.
http://www.panasonic.co.jp/global/
Dear customer
Thank you for your trust and your decision to purchase this top-quality device.
Panasonic is one of the leading manufacturers of entertainment electronics
devices. We are sure that you will be completely satisfied with this device.
2
Dispose of batteries, packaging
material and the unit according to
statutory regulations. They must not
be thrown into the household refuse.
Inserting Batteries
The batteries last for about a year, depending on how often you use the
remote control unit.
!
Do not mix old with new batteries or batteries of different types.
!
Only use batteries without any harmful substances (lead, cadmium, mercury).
!
Do not use rechargeable type batteries.
!
Remove the batteries if the remote control unit will remain unused
for longer periods of time.
!
Do not heat or short-circuit the batteries.
Immediately remove used-up batteries and replace
with batteries of type AA, UM3 or R6.
!
Be sure to put in the batteries the right way round (+ and -).
AC Mains Lead
RJA0043-1C
RF Coaxial cable
Batteries
AA, UM3 or R6
Operating Instructions
Guarantee Card
A
ccessories
Included
Remote control
N2QAJB000088: NV-SV121, NV-HV61, NV-MV21
N2QAJB000090: NV-HV51, NV-MV16
AV
ENTER
TV
CH
VCR
INPUT SEL
ShowView
AUDIO
RESET/CANCEL
REC MODE
OFF-TIMER
PROG PLAY
I-TIMER
MENU
EXIT
JET REW
CH
AV LINK
EXT LINK
STATUS
A
B
RECTIMER
INDEX
VOL
TRACKING/V-LOCK
N2QAJB000088
1
2
3
4
5
6
7
8
9
0
PROG
/CHECK
PAUSE/SLOW
VCR/TV
"Some functions may not be
applicable to your VCR."
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private
households)
This symbol on the products and/or accompanying documents means that used
electrical and electronic products should not be mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to
designated collection points, where they will be accepted on a free of charge basis.
Alternatively, in some countries you may be able to return your products to your local
retailer upon the purchase of an equivalent new product. Disposing of this product correctly will
help to save valuable resources and prevent any potential negative effects on human health and
the environment which could otherwise arise from inappropriate waste handling. Please contact
your local authority for further details of your nearest designated collection point. Penalties may
be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union. If you wish to discard this product, please contact
your local authorities or dealer and ask for the correct method of disposal.
Informasjon for brukerne om kassering av elektrisk og elektronisk utstyr (private
husholdninger)
r et produkt og/eller medfølgende dokumenter er merket med dette symbolet,
betyr det at det elektriske eller elektroniske utstyret ikke bør kasseres sammen med
vanlig husholdningsavfall. For at det kasserte utstyret skal bli behandlet, gjenvunnet og
resirkulert på riktig te, må du bringe det til rmeste innsamlingspunkt eller
gjenvinningsstasjon. I enkelte land kan du alternativt returnere produktene dine til den
lokale forhandleren, eventuelt mot kjøp av et tilsvarende nytt produkt. Hvis du kasserer dette
produktet på riktig te, bidrar til du til å bevare verdifulle ressurser og til å motvirke de negative
virkningene på milet og den menneskelige helse som kan forårsakes av feilaktig avfallsbehandling.
Ta kontakt med de lokale myndigheter hvis du ønsker ytterligere informasjon om ditt rmeste
innsamlingspunkt. Feilaktig kassering av dette utstyret kan kanskje bøtelegges, avhengig av
nasjonale lover og regler.
For bedriftskunder i den Europeiske Union
Hvis du ønsker å kassere elektrisk og elektronisk utstyr, må du kontakte forhandleren eller
leverandøren din for å få mer informasjon.
Informasjon om kassering i land utenfor den Europeiske Union
Dette symbolet er kun gyldig i den Europeiske Union. Hvis du ønsker å kassere dette produktet, må
du ta kontakt med forhandleren eller de lokale myndigheter og spørre dem om hvordan det skal
kasseres riktig måte.
-If you see this symbol-
-Hvis du ser dette symbolet-
The model and serial number of this product can be found on the back
of the unit. Please note them and keep for future reference.
Model No. Serial No.
Keep the VCR away from
high temperatures and avoid
changes in temperatures.
Avoid magnets or
magnetised objects.
Install the VCR in a horizontal
position. Do not place anything
heavy on it.
Don´t put fingers or
other objects inside.
Safety Precautions
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PRODUCT
DAMAGE, DO NOT EXPOSE THIS APPARATUS TO RAIN, MOISTURE,
DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH
LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.
THIS UNIT IS INTENDED FOR USE IN MODERATE CLIMATES.
This product may receive radio interference caused by mobile
telephones during use. If such interference is apparent, please
increase separation between the product and the mobile telephone.
CAUTION!
!
DO NOT INSTALL OR PLACE THIS UNIT IN A BOOKCASE, BUILT-
IN CABINET OR IN ANOTHER CONFINED SPACE. ENSURE THE
UNIT IS WELL VENTILATED. TO PREVENT RISK OF ELECTRIC
SHOCK OR FIRE HAZARD DUE TO OVERHEATING, ENSURE
THAT CURTAINS AND ANY OTHER MATERIALS DO NOT
OBSTRUCT THE VENTILATION VENTS.
!
DO NOT OBSTRUCT THE UNIT’S VENTILATION OPENINGS WITH
NEWSPAPERS, TABLECLOTHS, CURTAINS, AND SIMILAR ITEMS.
!
DO NOT PLACE SOURCES OF NAKED FLAMES, SUCH AS LIGHTED
CANDLES, ON THE UNIT.
!
DISPOSE OF BATTERIES IN AN ENVIRONMENTALLY FRIENDLY
MANNER.
3
The socket outlet shall be installed near the equipment and easily
accessible or the mains plug or an appliance coupler shall remain
readily operable.
NORSK
ADVARSEL:
FOR Å REDUSERE FAREN FOR BRANN, ELEKTRISK STØT
ELLER SKADER PÅ PRODUKTET, MÅ DETTE APPARATET
IKKE UTSETTES FOR REGN, FUKTIGHET, VANNDRÅPER
ELLER VANNSPRUT. DET MÅ HELLER IKKE PLASSERES
GJENSTANDER FYLT MED VANN, SLIK SOM
BLOMSTERVASER, OPPÅ APPARATET.
ADVARSEL!
!
APPARATET MÅ IKKE PLASSERES I EN BOKHYLLE, ET
INNEBYGGET KABINETT ELLER ET ANNET LUKKET STED
HVOR VENTILASJONSFORHOLDENE ER
UTILSTREKKELIGE. SØRG FOR AT GARDINER ELLER
LIGNENDE IKKE FORVERRER
VENTILASJONSFORHOLDENE, SÅ RISIKO FOR
ELEKTRISK SJOKK ELLER BRANN FORÅRSAKET AV
OVERHETING UNNGÅS.
!
APPARATETS VENTILASJONPNINGER MÅ IKKE DEKKES
TIL MED AVISER, BORDDUKER, GARDINER OG LIGNENDE.
!
PLASSER IKKE ÅPEN ILD, SLIK SOM LEVENDE LYS,
OPPÅ APPARATET.
!
BRUKTE BATTERIER MÅ KASSERES UTEN FARE FOR
MILJØET.
DETTE APPARATET ER BEREGNET TIL BRUK UNDER
MODERATE KLIMAFORHOLD.
Dette apparatet kan under bruk fange opp høyfrekvente
forstyrrelser forårsaket av en mobiltelefon som benyttes i
nærheten. Hvis slik forstyrrende påvirkning konstateres, bør
mobiltelefonen benyttes på større avstand fra dette apparatet.
Utstyret bør plasseres i nærheten av AC-stikkontakten, og
støpsletvære lett tilgjengelig hvis det skulle oppstå problemer.
Voltage: Only use power sources complying with the specifications
for this device.
AC mains lead protection: Ensure the AC mains lead is connected
correctly and not damaged. Poor connection and lead damage can
cause fire or electric shock.
Service: Never attempt to repair this unit by yourself. If a problem
occurs that is not described in these operating instructions, disconnect
the power supply and contact your dealer or an authorised after sales
service centre.
Keep away from humidity
and dust.
Keep away from liquids.
27
26
28
28
QUICK ERASE
27
28
20
21
21
EJECT
CH
REC
TIMER REC
Front Panel VCR
JET REW
28
TBC
SV121
CVC super (Crystal View Control super): The picture is automatically adjusted as clear and sharp as possible.
4
Record
Search
Fast winding
Playback
Erases a cassette.
Ejects the cassette.
Stop ends recording, playback, or winding.
Fast rewind to the beginning of the tape.
Time Base Correction: Optimises picture quality
Stand-by/on switch /I
VCR= Video Cassette Recorder
Activates the recording timer.
Channel selector
Page
Detailed information
is available on the
specified pages.
NV-SV121
NV-HV61, NV-HV51, NV-MV21, NV-MV16
.
SUPER LP 35x JET SEARCH
PULL OPEN
EJECT
TIMER REC
REC
CH
3D DNR
TBC
Super VHS
ET
CH
PULL OPEN
TIMER REC
REC
QUICK ERASE
JET REW
S-VIDEO
VIDEO
AUDIO
L/MONO
R
SV121 HV61 HV51 MV21 MV16
3D DNR
3-Dimensional Digital Noise Reduction
AC IN~ (Power supply)
AV2 (21-pin Scart socket)
AV1 (21-pin Scart socket)
1
2
3
4
AUDIO output
RF IN = Antenna input
RF OUT = Antenna output
5
7
8
R = AUDIO output right channel
L = AUDIO output left channel
S-VIDEO output
VIDEO output
1
2
3
4
7
8
AC IN~ (Power supply)
1
AC IN~ (Power supply)
AV (21-pin Scart socket)
1
5
RF IN = Antenna input
RF OUT = Antenna output
7
8
Rear Panel VCR
SV120 HV60 HV65 HV55 HV50 MV20 SV121 HV61 HV51 MV21 MV16
SV120 HV60 HV65 HV55 HV50 MV20
SV120 HV60 HV65 HV55 HV50 MV20
6
AC IN~ (Power supply)
1
4
AUDIO output
R = AUDIO output right channel
L = AUDIO output left channel
1
4
AV2 (21-pin Scart socket)
AV1 (21-pin Scart socket)
RF IN = Antenna input
RF OUT = Antenna output
5
7
8
7
8
6
AV2 (21-pin Scart socket)
AV1 (21-pin Scart socket)
RF IN = Antenna input
RF OUT = Antenna output
5
7
8
7
8
6
SV121 HV51 MV21 MV16 HV61
SV121 HV61 MV21 MV16HV51EC
SV121 HV61 HV51EG MV21 MV16
VIDEO
AUDIO
L
R
S VIDEO
AV1(TV)
AV2
(
AV2 (DECODER/EXT)
AC IN
~
AV OUT
RF IN
RF OUT
1
2
3
4
5
6
7
8
5
26
27
27
27
27
JET REW
INDEX
AV
CH
N2QAJB000088: NV-SV121, NV-HV61, NV-MV21
N2QAJB000090: NV-HV51, NV-MV16
Remote control functions
Some Panasonic television sets may be controlled with the remote control unit of this VCR.
Search beginning of a recording session.
Normal playback
Fast forward/rewind when stopped,
search forward or backwards during playback.
Stop ends recording, playback, or winding.
Eject: Press and hold for more than 3 seconds.
Stop a recording session.
Still playback or Slow Playback.
Volume control.
VCR Playback Control
TV Controls
Television set Stand-by/on switch.
6
Fast rewind to beginning of tape.
Channel selector.
Selects the TV set's AV port.
N2QAJB000088
VOL
PAUSE/SLOW
AV
ENTER
TV
CH
VCR
INPUT SEL
ShowView
AUDIO
RESET/CANCEL
REC MODE
OFF-TIMER
PROG PLAY
I-TIMER
MENU
EXIT
JET REW
CH
AV LINK
EXT LINK
STATUS
A
B
RECTIMER
INDEX
VOL
TRACKING/V-LOCK
N2QAJB000088
1
2
3
4
5
6
7
8
9
0
PROG
/CHECK
PAUSE/SLOW
VCR/TV
"Some functions may not be
applicable to your VCR."
21
20
20
16
16
24
23
26
21
22
28
14
14
25
13
Stand-by/on switch
Press to switch the unit from on to stand-by mode or vice versa.
In stand-by mode, the unit is still consuming a small amount of
power.
20
24
26
28
ENTER
REC
8 9
RESET/CANCEL
A
B
OFF-TIMER
EXIT
MENU
AUDIO
ShowView
AV LINK
EXT LINK
VCR
I-TIMER
Displays the menu.
VCR Recording Controls
Audio mode.
Sets the tape speed.
Record
Activate the recording timer mode.
Quits a menu.
Programming TV programmes broadcasted at the same
time and on the same channel.
Switches the VCR into stand-by mode after a preset
period of time during recording, playback or stop mode.
Press repeatedly to display the time,
tape counter or tape remain.
ShowView Menu (does not apply to HV51, MV16).
Menu navigation buttons.
ENTER: Selecting or storing settings.
VCR Standard Controls
Select programme storage position or enter
the ShowView number. E.g.: 18 =
Channel select buttons.
Tracking control of VCR picture disturbance.
7
Records with external recording control.
Switches from television reception to the video playback channel.
(does not apply to HV51EG, MV21, MV16)
Delete highlighted station.
Move highlighted station.
Displays the menu Timer recording.
Switches between AV inputs
A1, A2, A3 and Tuner (depending on model).
Plays back programmed recordings.
RESET : Resets the counter to 0:00.00.
CANCEL :Clears an entry you made.
INPUT SEL
PROG PLAY
REC MODE
TIMER
STATUS
CH
TRACKING/V-LOCK
PROG
/CHECK
4
TV
AC mains lead
SV121 HV61 HV51 MV21 MV16
SV121 HV61 MV21 HV51 MV16
SV121 HV61 MV21 HV51 MV16
VCR
1
2
3
4
4
3
2
1
Antenna
AC IN
RF IN
Antenna input
AV1
21-pin Scart socket
RF OUT
Antenna output
AC mains lead
Antenna input
RF coaxial cable
21-pin
Scart cable
AC IN~
8
VCR Auto Setup with 21-pin Scart cable
Connecting with a 21-pin Scart cable
Follow the steps
described below.
Disconnect power to
all devices.
Connect antenna to the
RF IN (Antenna input)
connector of the VCR.
Connect the VCR’s RF OUT
(Antenna output) to the
television set’s antenna input
connector.
Connect the VCR’s AV1 socket
(21-pin Scart socket) to the TV
set’s Scart In socket.
Connect VCR and TV set to
the AC mains supply.
!
Turn on your television set.
!
With the Stand-by/on switch turn on the VCR.
The Country menu appears.
!
With the arrow buttons select the according country, and
confirm by pressing ENTER.
Automatic tuning for all receivable TV stations begins.
Approximate duration is 5 minutes.
If menu Clock set appears
If time and date are not transmitted by a TV station, they must be set
manually.
!
Enter Time and Date with or ... , then
save with ENTER.
1 2 3
0
After running the automatic tuning Time and Date must be set manually.
!
Enter Time and Date with or ... , then
save with ENTER.
1 2 3
0
D
Mind that a wrong date or time will influence the programmed
recording of TV programmes (don't forget to change summer time
and winter time).
D
If the Country menu does not
appear after turning the device
on, you may reset the device to
its factory defaults (page 17).
Upon doing so the VCR Auto
Setup will start again.
(Automatic tuning)
AC mains lead
SV121 HV61 HV51 MV21 MV16
VCR
1
2
3
4
S-VIDEO output
AUDIO output
S-VIDEO cable
AUDIO cable
TV with S-VIDEO
input
S-VIDEO input
Antenna input
AC IN~
RF OUT
Antenna output
RF IN
Antenna input
4
AUDIO input
1
Antenna
2
5
5
5
3
TV
RF coaxial cable
AC mains lead
AC mains lead
9
Connecting with S-VIDEO cable.
Follow the steps
described below.
Disconnect power to
all devices.
Connect antenna to the
RF IN (Antenna input)
connector of the VCR.
Connect the VCR’s RF OUT
(Antenna output) to the
TV set’s antenna input
connector.
Connect the VCR´s S-VIDEO
output to the S-VIDEO input
of your television set.
Connect VCR and television
set to the AC mains supply.
VCR Auto Setup with S-VIDEO cable
!
Turn on your television set.
!
With the Stand-by/on switch turn on the VCR.
The Country menu appears.
!
With the arrow buttons select the according country, and
confirm by pressing ENTER.
Automatic tuning for all receivable TV stations begins.
Approximate duration is 5 minutes.
If menu Clock set appears
If time and date are not transmitted by a TV station, they must be set
manually.
!
Enter Time and Date with or ... , then
save with ENTER.
1 2 3
0
D
Mind that a wrong date or time will influence the programmed
recording of TV programmes (don't forget to change summer
time and winter time).
Connect the VCR’s AUDIO
output (L/R) to the AUDIO input
of your TV set.
This VCR supports the S-VHS format, providing a high picture quality
when playing back a S-VHS formatted cassette. When connecting via
a S-VIDEO cable, it is still possible to play back cassettes recorded
on the conventional VHS system.
D
If the Country menu does not
appear after turning the device
on, you may reset the device to
its factory defaults (page 17).
Upon doing so the VCR Auto
Setup will start again.
( )Automatic tuning
SV121 Only
SV121 HV61 HV51 MV21 MV16
SV121 HV61 MV21 HV51 MV16
SV121 HV61 MV21 HV51 MV16
VCR
3
1
2
3
1
2
3
AC IN~
Antenna
RF IN
Antenna input
RF OUT
Antenna output
Antenna input
RF coaxial cable
TV
AC mains lead
AC mains lead
10
Connecting with RF Coaxial cable
Connect antenna to the
RF IN (Antenna input)
connector of the VCR.
Connect the VCR´s RF OUT
(Antenna output) to the
television set’s antenna in
connector.
Connect VCR and television
set to the AC mains supply.
Follow the steps
described below.
Disconnect power to
all devices.
You can connect the VCR to your TV set
by using a RF coaxial cable.
VCR Auto Setup with RF Coaxial cable
D
Mind that a wrong date or time will influence the programmed
recording of TV programmes (don't forget to change summer time
and winter time).
D
If the Country menu does not
appear after turning the device on,
you may reset the device to its
factory defaults (page 17). Upon
doing so the VCR Auto Setup will
start again.
The Country menu appears.
!
With the arrow buttons select the according country, and
confirm with ENTER.
Automatic tuning for all receivable TV stations begins.
Approximate duration is 5 minutes.
If menu Clock set appears
If time and date are not transmitted by a TV station, they must be set
manually.
!
Enter Time and Date with or ... , then
save with ENTER.
1 2 3
0
After running the automatic tuning Time and Date must be set
manually.
!
Enter Time and Date with or ... , then
save with ENTER.
1 2 3
0
(Automatic tuning)
11
(RF OFF)
21
69
...
VCR Display
RF Output Channel
Test pattern
VCR Ch:39
Screen Display
!
Press MENU for about 5 seconds. The preset channel will be
displayed on the VCR-display.
!
Press channel select buttons CH or 0 to invoke [- -].
!
Confirm with ENTER.
If a 21-pin Scart cable is used, please adjust the following
settings to disable the VCR´s RF-output channel.
Channel tuning / Correcting interferences
!
Turn on your television set.
!
Turn on the VCR by pressing the Stand-by/on switch.
!
Press MENU for about 5 seconds. The preset channel is
displayed on the VCR-display.
!
Adjust television set to show the test picture.
If there are any interferences select another channel on the
television set and the VCR.
!
Press the CH button to change the channel
(e.g. Channel 39). Fine-tune television set until
a clear picture is displayed.
!
Confirm with ENTER.
Continue VCR Auto Setup (Automatic tuning).
D
The VCR will not initiate the VCR Auto Setup if it was run once
before.
Reset the device to factory defaults (page 17). Upon doing so
you will be able to start VCR Auto Setup again.
D
Press EXIT to abort VCR Auto Setup. You can run VCR Auto
Setup again at another time.
!
Press MENU,
the Menu screen appears.
!
With select Clock set.
!
Press ENTER.
Setting Time and Date
: select : access
: return : exit
ENTER
MENU EXIT
!
Select [AUTO] and confirm with
ENTER.
Menu
!
Select [MANUAL] and confirm with
ENTER.
!
With or ...
enter Time and Date, then store
with ENTER.
1 2 3
0
: select : access
: exit
ENTER
EXIT
Timer recording
Tuning
Clock set
Others
Language : English
Test pattern
VCR Ch:36
AUTO
Time : 12 : 00 : 00
Date : 11. 6. 04
RF Output Channel
If you decide to just use the RF coaxial cable to connect the TV set you must adjust the
video output channel with the TV set’s input channel.
Automatic tuning
If the device does not find a TV
station broadcasting the time
signal, set Time and Date manually.
Manual tuning
Clock set
: select : access
: return : exit
ENTER
MENU EXIT
MANUAL
Time : 12 : 00 : 00
Date : 11. 6. 04
Clock set
CH
TRACKING/V-LOCK
SV121
HV61 HV51EC
21-pin Scart cable
TV
External unit
VCR
Antenna
SV121 HV61 HV51EC HV51EG MV21 MV16
12
External Devices
Setting the channel to decoder
!
Press MENU.
!
With select menu Tuning
and confirm with ENTER.
!
With ENTER select Manual.
!
With , select the encrypted channel and
confirm with ENTER.
!
With select Decoder, then select [ON] with .
!
Press MENU to return to the Tuning menu.
Disconnect power to all devices.
Connect the external device to the AV2 input of the VCR by
using a 21-pin Scart cable.
Connect VCR, television set and the external unit to the AC
mains supply and switch it on.
!
Press MENU.
!
With select the Others menu and confirm with ENTER.
Connecting a Set Top Box, satellite receiver, decoder or a second recorder.
You can connect a Set Top Box to receive digital broadcast by antenna (DVB-T) signals,
a satellite receiver (digital/analogue) or a decoder to decrypt encrypted programmes.
Decoder:
!
Select AV2 with , and set to [DECODER] with .
This setting does not allow you to change option AV2 IN.
!
Press MENU to return to the Menu screen.
When using a decoder switch channel to decoder.
Set Top Box, satellite receiver, second recorder:
!
Select AV2 with , and set to [EXT] with .
Tape length : AUTO ( E-240)
AV2 : EXT
TV system : AUTO
SQPB : AUTO
OSD : 4 : 3
Power save : OFF
VCR display: ON
Others 1 / 2
Tape length : AUTO ( E-240)
AV2 : DECODER
AV1 OUT : VIDEO
TV system : AUTO
S-VHS playback : AUTO
OSD : 4 : 3
AV2 IN : VIDEO
Others 1 / 2
Tuning
Pos Name Ch Pos Name Ch
1 ARD 7
2 ZDF 4
3 N3 2
4 RTL 12
5 SAT1 13
: delete : move
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
Pos
Name
Channel
Fine tuning
Decoder
Video system
Mono
:
: PREM
: 97
AUTO
:
: PAL
: OFF
- - -
ON
9
:
: select
: return : exit
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
6 VOX 8
7 PRO7 95
8 RTL2 85
9 PREM 97
10 S-RTL 98
: : access
select
: return : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
VCR
AUDIO cable
Amplifier
Video
Audio
L R
SV120 HV60 HV65 HV55 HV50 MV20
SV121 HV61 HV51 MV21 MV16
SV121 HV61 HV51 MV21 MV16
PULL OPEN
TIMER REC
REC
QUICK ERASE
JET REW
S-VIDEO
VIDEO
AUDIO
L/MONO
R
External Devices
Connecting an amplifier
Disconnect power to all devices.
Use an audio cable to connect your VCR to a stereo amplifier.
Left = white (L) Right = red (R)
Connect VCR, television set and the Amplifier to the AC mains supply.
D
If you have a scart adapter cable you can also connect the
VCR’s AV socket to an amplifier.
Connecting to the AV3 input
!
Connect the VIDEO/S-VIDEO output of the device to be connected to the
front panel VIDEO/S-VIDEO input of the VCR (e.g. a video camcorder).
!
Connect the AUDIO output of the device to be connected to the AUDIO input
of the VCR.
!
With INPUT SEL select A3.
13
D
To record the audio signal in Mono format, connect only the L/MONO input.
LP
INPUT SEL
Menu
Timer recording
Tuning
Clock set
Others
Language : English
-- ---- -- / -- --:-- --:-- - ---
-- ---- -- / -- --:-- --:-- - ---
-- ---- -- / -- --:-- --:-- - ---
-- ---- -- / -- --:-- --:-- - ---
-- ---- -- / -- --:-- --:-- - ---
-- ---- -- / -- --:-- --:-- - ---
Timer recording 1/3
VPS
PDC
Pos Date Start Stop
Clock set
AUTO
Time : 12 : 00 : 00
Date : 11. 6. 04
Tuning
Manual
Auto Setup
Shipping condition
Tape length : AUTO ( E-240)
AV2 : DECODER
AV1 OUT : VIDEO
TV system : AUTO
S-VHS playback : AUTO
OSD : 4 : 3
AV2 IN : VIDEO
Others 1 / 2
9
11
21
22
15
18 19
ENTER
The cursor buttons on the remote control
unit allow you to navigate through menus
and change selected entries.
!
With select the entry you would like to change,
then confirm with ENTER.
!
Make your changes following the menu steps.
!
With MENU return to the previous menu.
!
Press EXIT to leave the menu.
Menu
!
Press MENU, the menu screen appears.
!
With select the desired sub-menu.
!
Press ENTER, the selected menu appears.
14
D
Not every model supports all of the functions.
D
Not every model supports all of the functions.
Options available for tuning the channels
Pos
Name
Channel
Fine tuning
Decoder
Video system
Mono
AUTO / MAN.
ON / OFF
AUTO / PAL / MESECAM
ON / OFF
Station position.
Station name setting.
Channel setting.
Fine tuning of disturbed picture.
Switch stereo to mono.
TV system setup.
For reception of encrypted channels.
!
Enter channel with the or ... buttons.
Channel tuning starts. Wait until the desired station has been set.
Fine tuning may help to minimise any interference.
!
Press MENU to return to the Tuning screen.
1 2 3
0
Manual Setup
Creating a new station table
!
Press MENU, the Menu screen appears.
!
Select the Tuning menu by pressing and confirming with ENTER.
!
Confirm Manual by pressing ENTER.
!
With the buttons, select an open storage position.
!
Press ENTER.
15
Pos Name Ch Pos Name Ch
1 ARD 7
2 ZDF 4
3 N3 2
4 RTL 12
5 SAT1 13
Pos
Name
Channel
Fine tuning
Decoder
Video system
Mono
: 7
: - - - -
: :
AUTO
: OFF
: AUTO
: OFF
- - -
:
Tuning
: select
: return : exit
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
: : access
select
: return : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
: delete : move
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB
6 VOX 8
7 - - - - - - -
8 - - - - - - -
9 - - - - - - -
10 - - - - - - -
Changing the name of TV stations
!
Press MENU, the Menu screen appears.
!
With select the Tuning menu, confirm with ENTER.
!
Confirm Manual with ENTER.
!
With select the name entry.
!
Press ENTER.
Changing the order of TV stations or deleting a station
!
Press MENU, the Menu screen appears.
!
With select the Tuning menu, confirm with ENTER.
!
Confirm Manual with ENTER.
!
Press . An arrow to the left will mark the selected field.
!
With move the station to any other desired location.
!
Press ENTER.
!
Press to delete the station.
BBBBBBBBBBBBBBBBBBB
A
!
With select the name entry.
The cursor will mark the first letter .
!
With change that letter.
!
With select the next letter .
!
Press MENU.
The new name will be stored in Tuning.
ARD
A DR
Manual Setup
16
Tuning
Pos Name Ch Pos Name Ch
6 VOX 8
7 PRO7 95
8 RTL2 85
9 KABE 97
10 S-RTL 98
Pos
Name
Channel
Fine tuning
Decoder
Video system
Mono
: 1
:
: 7
: AUTO
: OFF
: AUTO
: OFF
ARD
: : access
select
: return : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
delete
: : move
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
B
Tuning
Pos Name Ch Pos Name Ch
6 VOX 8
7 PRO7 95
8 RTL2 85
9 KABE 97
10 S-RTL 98
delete
: : move
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
B
: select
: return : exit
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
1 ARD 7
2 ZDF 4
3 N3 2
4 RTL 12
5 SAT1 13
1 ARD 7
2 ZDF 4
3 N3 2
4 RTL 12
5 SAT1 13
: : store
move
: return : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
Creating a new station table
!
Press MENU, the Menu screen appears.
!
With select the Tuning menu, confirm with ENTER.
!
With select Auto Setup, confirm with ENTER.
!
Press ENTER to confirm.
Shipping condition/factory defaults
!
Press MENU, the Menu screen appears.
!
With select the Tuning menu, confirm with ENTER.
!
With select Shipping condition and confirm with ENTER.
!
Press ENTER to confirm.
D
To restore factory defaults briefly unplug the AC mains lead.
Afterwards you will have to run VCR Auto Setup again.
The Country menu appears.
!
Select country with and confirm with ENTER.
The Auto Setup menu will be displayed.
The Automatic Tuning will start.
Manual Setup
17
Tuning
Manual
Auto Setup
Shipping condition
: yes : no
ENTERENTERENTERENTERENTERENTERENTERENTER
EXITEXITEXITEXITEXITEXITEXITEXIT
OK?
Auto Setup
Country : others
Tuning : Ch 1
Tuning
Manual
Auto Setup
Shipping condition
: yes : no
ENTERENTERENTERENTERENTERENTERENTERENTER
EXITEXITEXITEXITEXITEXITEXITEXIT
OK?
Menu Others
HV61 HV51EC
SV121
HV51EG MV21 MV16
Tape length
Sets the tape length of the cassette you use.
( ),
AUTO E - 240 E - 195, E - 260, E - 300
AV2
DECODER : If a decoder is connected.
EXT : If another video recorder or satellite receiver is connected.
AV2 IN
AV1 OUT
VIDEO : If the unit does not support S-VIDEO.
S-VIDEO : If the unit supports S-VIDEO.
To connect use a 21-pin scart cable.
VIDEO : Video signal via the 21-pin scart cable.
S-VIDEO : S-Video signal via the 21-pin scart cable.
Allows you to record the S-Video signal of an external unit connected
to the video recorder's AV2 socket.
Selects the type of external unit connected to the VCR's socket. AV2
TV system
S-VHS playback
OSD
AUTO : The VCR automatically detects the type of recording.
ON : Plays back S-VHS format cassettes in the S-VHS format only.
OFF : Plays back cassettes recorded in VHS format only.
AUTO : Automatically detects PAL or MESECAM.
PAL : If you are using the PAL system.
MESECAM : If you are using the MESECAM system.
4:3 : Displays appear at the edge of the screen
(displays not visible on 16:9 format screens).
WIDE : Displays appear at the edge of the screen
(displays appear in the middle on 4:3 format screens).
OFF : No on-screen displays.
SQPB
AUTO : The VCR automatically detects the type of recording.
ON : Plays back S-VHS format cassettes in quasi S-VHS format.
OFF : Plays back cassettes recorded in VHS format only.
Tape length : AUTO ( E-240)
TV system : AUTO
SQPB : AUTO
OSD : 4 : 3
Power save : OFF
VCR display : DIMMED
EXT LINK : 2
Tape length : AUTO( E-240)
AV2 : DECODER
TV system : AUTO
SQPB : AUTO
OSD : 4 : 3
Power save : OFF
VCR display : DIMMED
Others 1 / 2
Others
Tape length : AUTO ( E-240)
AV2 : DECODER
AV1 OUT : VIDEO
TV system : AUTO
S-VHS playback : AUTO
OSD : 4 : 3
AV2 IN : VIDEO
Others 1 / 2
18
SV121
HV61 HV51EC
Menu Others
Power save
ON : The video recorder's display unit is off. In Power save mode,
you cannot change the VCR display setting.
To control an external appliance via AV2 Scart socket,
the VCR first needs to be switched on.
OFF : Factory setting; you can change the VCR display setting.
Press to display the 2nd screen.
S-VHS REC
S-VHS ET REC
EXT LINK
VCR display
DIMMED : The video recorder's display is dimmed.
ON : The video recorder's display unit is on at normal brightness.
2 : External recording control by satellite receivers or
digital receivers (video signal).
1 : For digital receivers transmitting a special recording
control signal, e.g. the F.U.N. receiver (TU-DSF41).
ON : For S-VHS format recordings on a S-VHS type cassette.
OFF : For VHS format recordings on a S-VHS type cassette.
Available only if the unit is not in Power save mode.
ON : Takes recordings at a higher picture quality on VHS-HG
cassettes.
OFF : Takes standard quality recordings.
In SP mode only
Only in stand-by mode
In conjunction with the PAL TV system only.
In conjunction with the PAL TV system only.
Only in stand-by mode
EXT LINK : 2
Others 2 / 2
Others 2 / 2
Power save : OFF
VCR display : DIMMED
S-VHS REC : ON
S-VHS ET REC : OFF
EXT LINK : 2
19
REC
25
24
23
21
20
REC
SV121 HV61 HV51 MV21 MV16
20
SP : normal recording time - optimal picture quality
LP : double recording time - simple picture quality
EP : triple recording time - reduced picture quality
When playing back LP or EP recordings, interferences may occur when
using certain types of cassettes (e.g. Type E-300). These are not
indicative of a VCR malfuncion.
Tape speed
!
Prior to starting the recording session, press REC MODE to set
the tape speed.
Set the TV set to the video channel and insert a cassette into the VCR;
make sure that the cassette’s protection tab is intact.
!
Select channel to record from.
When recording from an external device, select from
Scart inputs AV1, AV2, or the front panel input AV3.
!
Press REC to start recording.
!
Press STOP to stop recording.
!
Press PAUSE/SLOW to pause recording.
To protect the video heads this function will be terminated after
approx. 5 minutes.
!
Press PAUSE/SLOW again to resume recording.
Recording
D
Recordings in the S-VHS or S-VHS ET REC mode are supported
by the PAL TV system only (SV121 only, page 19).
Tape Remain counter
The display of the VCR shows:
Time - Counter - Tape Remain.
!
Press STATUS until [RE] is displayed.
Timer recording
Recording with INTELLIGENT TIMER
Recording with ShowView
Recording with external recording controls
Direct recording of the
VCR - TV picture.
Recording controlled by timer.
Repeating programmed
recordings.
Programming recordings using
the ShowView function.
Recording is controlled
by an external device.
Recording functions
STATUS
REC MODE
SV121 HV61 HV51 MV21 MV16
Timer recording
The Timer recording allows you to programme the recording time of TV programmes
up to 1 month in advance. Use the on-screen menu to programme a maximum of 16
recordings.
Quitting the timer mode
!
Press TIMER, the VCR symbol will turn off.
You can now play back a cassette or make a manual recording. Press TIMER
again to reactivate the previously entered timer programme.
!
Press PROG/CHECK and select a free storage position .
!
Confirm with ENTER.
!
Select a station , and use to set date, week or weekday .
!
Then enter start- and stop-time , .
!
Hold buttons down to change time in 30-minute steps.
!
Select tape speed: A (Automatic), SP, LP, EP , .
!
The VPS/PDC settings may be changed with (does not apply to HV51, MV16).
!
Press ENTER to save timer programme.
!
Repeat these steps for further recordings you may wish to programme.
!
Press TIMER to activate the VCR´s timer mode.
Make sure the VCR symbol is displayed.
D
Do not forget to verify that there is enough tape left. The length of the recording
must not exceed the tape left on the video cassette.
21
Timer recording 1 / 3
Pos Date Start Stop
VPS
PDC
1 ARD 31/12 10:30 11:30 SP ON
1 ARD 31/12 11:30 12:30 SP ON
2 ZDF 31/12 12:30 13:30 SP ON
4 RTL 31/12 13:30 14:30 SP ON
6 VOX 31/12 14:30 15:30 SP ON
-- - - - - - -/ - - - -:- - - -:- - SP - - -
:select : store
: delete : exit
ENTER
CANCEL
EXIT
Timer recording 1 / 3
Pos Date Start Stop
VPS
PDC
1 ARD 31/12 10:30 11:30 SP ON
1 ARD 31/12 11:30 12:30 SP ON
2 ZDF 31/12 12:30 13:30 SP ON
4 RTL 31/12 13:30 14:30 SP ON
6 VOX 31/12 14:30 15:30 SP ON
-- - - - - - -/ - - - -:- - - -:- - SP - - -
: select : store
: delete : exit
ENTER
CANCEL
EXIT
TIMER
SV121 HV61 MV21 HV51 MV16
SV121 HV61 HV51 MV21 MV16
SV121 HV61 HV51 MV21 MV16
Checking the timer programme
!
Press PROG/CHECK,
the Timer recording menu appears.
!
Press PROG/CHECK again or EXIT
to quit the menu.
Playing back programmed recordings
!
Press PROG PLAY.
The device will rewind to the beginning of the recording,
and automatically start playing it back.
Automatic SP/LP selection
A: If, at the beginning of a timer programme, there is not
enough tape left to complete it, the SP/LP function will
automatically run the tape at LP speed. This ensures that the
entire programme will be recorded. If the LP mode is not
enough to ‘stretch’ the remaining tape to fit, you will not be
able to record all of the TV programmes.
D
It is not possible to automatically activate the EP mode.
VPS/PDC function
If a TV programme begins or ends earlier or later than planned,
this function synchronises the beginning and end of the
recording session with the actual beginning and end of the TV
programme through a VPS signal transmitted by the TV station.
ON : The station transmits VPS/PDC signals. You must set the
timer to the time specified in the TV magazines. Use the
special VPS time the TV magazine may indicate.
- - - : The station does not transmit VPS/PDC signals. Try to set
the start and stop time such that the entire film can be
recorded even if a programme begins or ends earlier or
later than planned.
22
Changing or cancelling a timer programme
!
Press PROG/CHECK,
the Timer recording menu appears.
! With select the entry you would like to edit,
confirm with ENTER.
!
Modify entries with and confirm with ENTER.
!
Press RESET/CANCEL to delete a recording.
Timer recording
I-TIMER
SV121 HV61 HV51 MV21 MV16
Recording with
INTELLIGENT TIMER
Protecting I-TIMER programmes
If there are 5 entries in the INTELLIGENT TIMER menu, the next and every following
entry overwrites the oldest programme setting.
!
Press I-TIMER.
!
With select an entry.
!
To protect the entry press . The symbol appears.
!
To remove protection press . The symbol disappears.
Editing a programme
!
Press I-TIMER.
!
Press or I-TIMER to select a programme and confirm with ENTER.
!
The Timer recording screen appears.
!
With modify the desired data, and store changes with ENTER.
!
Press TIMER to activate the timer mode.
Copying stored recording sessions
!
Press I-TIMER.
!
With or I-TIMER select recording session.
!
Press TIMER to activate the timer mode.
23
The INTELLIGENT TIMER allows you to easily time the recording of programmes
broadcasted by the same TV station at the same daytime at different days.
To use the INTELLIGENT TIMER function, at least one recording session must be
programmed in the Timer recording menu (page 21). This information will be copied into
the INTELLIGENT TIMER menu.
Upon completing the programmed recording session, such session information will be
deleted from the Timer recording menu, but remain available in the INTELLIGENT TIMER
menu. From there such information may be copied back to the Timer recording menu, thus
allowing you to easily programme the recording session again with changed dates.
The INTELLIGENT TIMER menu will contain information about the last 5 programmed
recording sessions.
Pos Date Start Stop
VPS
PDC
1 ARD 25/10 10:30 11:30 SP ON
1 ARD 25/10 18:30 19:30 SP OFF
2 ZDF 25/10 12:30 13:30 A ON
INTELLIGENT TIMER 25/10/04
: edit : unlock : lock
: delete : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
CANCELCANCELCANCELCANCELCANCELCANCELCANCELCANCEL
EXITEXITEXITEXITEXITEXITEXITEXIT
: select : store
I-TIMER
TIMER
Timer recording 1 / 3
: select : store
: delete : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
CANCELCANCELCANCELCANCELCANCELCANCELCANCELCANCEL
EXITEXITEXITEXITEXITEXITEXITEXIT
Pos Date Start Stop
VPS
PDC
1 ARD 26/10 10:30 11 :30 SP ON
1 ARD 26/10 18:30 19:30 SP OFF
- - - - - - - -/ - - - - :- - - - :- - - - - -
- - - - - - - -/ - - - - :- - - - :- - - - - -
- - - - - - - -/ - - - - :- - - - :- - - - - -
- - - - - - - -/ - - - - :- - - - :- - - - - -
- - - - - - - -/ - - - - :- - - - :- - - - - -
ShowView
is a trademark of Gemstar Development
Corporation. The ShowView system is
manufactured under licence from
Gemstar Development Corporation.
ShowView
SV120 HV60 HV65 HV55 HV50 MV20
SV121 HV61 MV21 HV51 MV16
Recording with ShowView
Activating timer mode
!
Press TIMER to activate the timer mode.
The symbol appears on the VCR display.
Programming recordings with the ShowView function
The ShowView code simplifies entering programme information to record
TV and SAT programmes.
!
Press ShowView.
!
Enter the ShowView number ( to correct entry).
!
Confirm entry with ENTER.
The Timer recording screen appears.
If the device fails to recognise the TV station automatically, it must be
entered manually with . The VCR will store this information so it will
not have to be entered again.
Modifying programmed data
!
Press PROG/CHECK,
the Timer recording menu appears.
!
With select the entry to be modified, confirm with ENTER.
!
Select station and use to set date, week or weekday , .
!
Then enter start and stop time , .
!
Select tape speed: A (Automatic), SP, LP, EP , and confirm
with ENTER.
!
Press TIMER to activate the VCR’s timer mode.
24
ShowView
: enter : access
0 - 9
: correct : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
EXITEXITEXITEXITEXITEXITEXITEXIT
8 3 5 4 2 - - - -
Timer recording 1/3
: select access
:
: delete : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
CANCELCANCELCANCELCANCELCANCELCANCELCANCELCANCEL
EXITEXITEXITEXITEXITEXITEXITEXIT
Pos Date Start Stop
VPS
PDC
1 ARD 31/12 10:30 11:30 SP ON
1 ARD 31/12 11:30 12:30 SP ON
2 ZDF 31/12 12:30 13:30 SP OFF
- - - - - - - -/ - - - -:- - - -:- - - - - -
- - - - - - - -/ - - - -:- - - -:- - - - - -
- - - - - - - -/ - - - -:- - - -:- - - - - -
TIMER
SV121 HV61 HV51 MV21 MV16
EXT LINK
Receiver
1
2
VCR
Aerial
1 NV-SV121, NV-HV61, NV-HV51EC
2 NV-HV51EG, NV-MV21, NV-MV16
TV
!
Press MENU, the Menu screen appears.
!
With select menu Others
and confirm with ENTER.
!
With select EXT LINK and turn to
[2] or [1] .
!
Press MENU to return to the Menu screen.
EXT LINK 2: External recording control for some
satellite or digital receivers (video signal).
EXT LINK 1: For digital receivers transmitting a
special recording control signal, e.g. the F.U.N.
receiver (TU-DSF41).
D
Be sure that the timer programmes stored by your VCR do not overlap with
the ones of the satellite or digital receiver.
Recording with external
recording controls
25
Quitting recording stand-by mode
!
Press EXT LINK to quit recording stand-by mode.
The EL1 or EL2 display disappears.
You can now play back a cassette or make a manual recording. You must
press EXT LINK again to reactivate the recording stand-by mode.
!
Press EXT LINK to activate the VCR´s recording stand-by mode.
Make sure the VCR´s EL1 or EL2 display appears.
As long as the satellite or digital receiver transmits the special recording
signal (EL1), or a video picture is transmitted (EL2), the VCR will continue
to record.
!
Press ENTER to hide this message.
!
Press EXT LINK to stop recording.
Power save : OFF
VCR display : DIMMED
S-VHS REC : ON
S-VHS ET REC : OFF
EXT LINK : 2
: select
: return : exit
MENU
EXIT
Others 2 / 2
ENTER : yes EXT LINK : cancel
EXT LINK recording in progress
The following screen will be shown
if you select EXT LINK: [2]:
SV120 HV60 HV65 HV55 HV50 MV20
SV121 HV61 HV51 MV21 MV16
OFF-TIMER
Time limited recording or playback
During recording, playback or stop mode the device
switches to stand-by after a preset period of time.
Press the button repeatedly to increase this period from
30 to 60, 120, 180 or 240 minutes.
The set time appears in the VCR’s display.
!
Press OFF-TIMER
26
Normal playback
!
Turn on the VCR.
!
Be sure the TV set is turned on and tuned to the video
playback channel.
!
Insert a video cassette.
!
Press PLAY to start playback.
!
Press STOP to end playback.
Playback
Repeat playback
The VCR repeats playback from beginning to the end of
the recording.
!
In stop or playback mode press PLAY for longer
than 5 seconds.
The symbol [R] appears on the VCR´s display.
!
Press STOP to end playback.
Starting automatic playback
When inserting a cassette with removed protection tab,
playback will start automatically.
Playback from power stand-by mode
When inserting a cassette and pressing PLAY ,
the device will turn itself on and start playing back.
Normally the VCR automatically adjusts the playback
picture to the highest possible quality. Sometimes it
may be necessary though to adjust the picture
manually.
Picture noise or unclear picture during playback.
(Tracking)
!
While in regular playback
or in slow motion press
programme selection button
(-) or (+) until the noise
disappears.
If noise appears in a still
picture, first switch VCR
to slow motion, then
adjust tracking.
D
In some video cassettes tracking can not
be adjusted. This is not indicative of a VCR
malfunction.
Automatic tracking control
!
Simultaneously press (-) and (+).
The still picture runs up or down
!
In still playback mode hold (-) or (+)
until the picture stands still.
D
On some TV sets special playback functions may
cause the picture to shift up or down. This is not
a VCR malfunction.
Optimising the playback picture quality
SV121 HV61 HV51 MV21 MV16
SV121 HV61 HV51 MV21 MV16
General convenient functions
Auto-Start
When inserting a cassette the VCR will automatically
switch on.
Automatic stop function
To protect the video heads the device will automatically quit
the functions search backwards/forwards, quick search, still
playback and slow playback after 5-10 minutes. Interference
and motor noise are not a malfunction.
27
Automatic rewinding
When a cassette is played to the end, the VCR will
automatically rewind it to the beginning of the tape.
D
This function is not available during programmed
recording sessions.
Fast winding forward or backwards
!
In stop mode press or .
!
Press STOP to end winding.
Quick search for a beginning of a recording
While playing back or in stop-mode.
!
INDEX tape winds forward / INDEX tape rewinds.
Every time you press the button (max. 20 times) the
VCR will find the start of the next recording.
Playback will start automatically.
!
Press STOP to exit the Search function.
Search forward or backwards
!
While playing back press or , the search begins.
!
When pressing the button twice (JET SEARCH) the
search speed increases.
!
When holding the button down the search will run for
the duration of the button being held.
!
Press PLAY to end search.
Still playback
!
Press PAUSE/SLOW during playback.
!
To exit still playback press PAUSE/SLOW again or PLAY .
Slow playback (does not apply to MV21, MV16)
!
During playback press PAUSE/SLOW for longer than 2
seconds.
!
To exit slow motion playback press PLAY .
JET REW
For fast rewinding to the beginning of the tape.
On a E180 cassette approx. 43 seconds.
D
Tape counter and tape remain display are unavailable
during this function.
D
This function is not available in some cases
(e.g. at the beginning or end of the tape).
SV121 HV61 HV51 MV21 MV16
SV121 HV61 HV51 MV21 MV16
SV121 HV61 HV51 MV21 MV16
SV121 HV61 HV51 MV21 MV16
Stick adhesive tape over the
gap if you wish to re-record
a protected cassette.
28
General convenient functions
AUDIO settings
Select audio playback mode by repeatedly pressing the
AUDIO button.
Stereo playback: Display: L R
Left channel: Display: L -
Right channel: Display: - R
Mono playback: Display: - -
3D DNR, 3-Dimensional Digital Noise Reduction
Improving picture quality by noise reduction.
!
Press the 3D DNR button to deactivate this function.
The status will be displayed on the TV screen.
QUICK ERASE
To record on a cassette containing previous recordings
without loss of quality, erase these recordings with the
QUICK ERASE function.
!
Press and hold the QUICK ERASE button for a few
seconds.
It takes approx. 30 minutes to erase an E-180 cassette.
TBC, TIME BASE CORRECTION
TBC offers undistorted and stable playback picture quality.
!
Press the TBC button to deactivate this function.
The status will be displayed on the TV screen.
Device only operation.
Cassette erasure protection
Break out the erasure protection tab to
protect the cassette against accidental
erasure of recordings you wish to keep.
Automatic shut down and removing cassettes
If the VCR is switched into stand-by mode, the cassette
may be removed by pressing the EJECT-button.
Once done the VCR will switch back to stand-by mode.
Tape Counter
When inserting a video cassette the tape counter will
automatically reset to [0:00.00].
!
The tape counter may also be reset to [0:00.00] by
pressing the RESET/CANCEL button.
High quality functions
SV121 HV61 MV21 HV51 MV16
SV121EC HV61EC HV51EC
Playing back NTSC video cassettes
You can play back NTSC video cassettes for viewing on a PAL system TV set.
If there is any interference when playing back NTSC, try readjusting your TV set.
Read the operating instructions of your TV set. You cannot record or copy
video cassettes in NTSC format.
NTSC playback
Select Mono: [ON] to record mono sound to the Hi-Fi audio tracks of the VCR,
or if the quality of stereo sound reception is bad.
NICAM sound system
!
Press MENU, the Menu screen appears.
!
With select the Tuning menu and confirm
with ENTER.
!
Confirm Manual with ENTER.
!
With select the desired channel
and confirm with ENTER.
!
With select Mono and switch to [ON] or
[OFF] with .
!
Press MENU to return to Tuning.
29
: select
: return : exit
MENU
EXIT
Pos
Name
Channel
Fine tuning
Decoder
Video system
Mono
: 1
: ARD
: 7
: AUTO
: OFF
: PAL
:
OFF
Tuning
Pos Name Ch Pos Name Ch
6 VOX 8
7 PRO7 95
8 RTL2 85
9 KABE 97
10 S-RTL 98
delete
: : move
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
B
1 ARD 7
2 ZDF 4
3 N3 2
4 RTL 12
5 SAT1 13
: : access
select
: return : exit
ENTERENTERENTERENTERENTERENTERENTERENTER
MENUMENUMENUMENUMENUMENUMENUMENU
EXITEXITEXITEXITEXITEXITEXITEXIT
Please contact our after sales service centre if you fail to remove problems by yourself (see Guarantee Information).
21
18
21
22
11
18
11
2
19
30
!
Check AC mains connection.
!
Check Power save
The recording functions do not work properly:
!
If flashes on the device, check if the protection tab of the video
cassette is still in.
!
Check Time and Date
!
Check the start and stop time of the timer programme.
!
Check if the TIMER button has been pressed to put the device
into timer mode after programming a recording.
!
Check the start and stop time of a VPS/PDC recording.
Remote control unit functions don’t work:
!
Check distance to the device (max. 7 metres).
!
Check remote control unit’s batteries
Bad picture or sound:
!
Fast winding forward and backwards causes motor noises.
These are not malfunctions.
!
Device is set to recording stand-by or timer mode.
Quit with EXT LINK button or TIMER button.
The VCR display is not lit:
The VCR display is lit, the device does not respond to controls:
Raised motor noise level:
Automatic Clock set doesn’t work properly:
!
The use of E-300 cassettes may cause problems if the recordings
were taken at low tape speeds (LP or EP)
.
!
Check [PAL] and [MESECAM] settings.
!
Verify that the aerial and/or Scart cables are attached and work
properly.
!
Check the SQPB/ S-VHS playback setting for S-VHS cassettes.
!
Faulty recordings taken at slow tape speed (EP) in [MESECAM]
are not malfunctions.
!
Please contact your service technician if the video heads are dirty
or worn out.
!
Having a technical service shop clean the video heads is not
covered by the guarantee.
!
Set Clock set to [AUTO]
If the device cannot find a TV station transmitting the time signal,
set Time and Date manually.
Before requesting service
Power supply
80 Hz to 8 kHz (SP, Mono),
More than 43 dB (SP, Mono)
PAL colour signal
Record and playback time (E-240 cassette) SP: 240 min, LP: 480 min
SP: 23.39 mm/s, LP: 11.7 mm/s
S-VHS/Hi-Fi: 4 heads / 2 Audio heads, Mono: 2 heads
Controls
20 Hz to 20 kHz (Hi-Fi sound tracks)
S-VHS Quasi Playback (SQPB)
S-VHS
S-VHS ET
Specifications
D
These specifications are subject
to change without notice.
Weight and dimensions (approximate value) 3.5 kg / 430 (width) x 89 (height) x 276 mm (depth)
Operating temperature / humidity 5°C to 40°C / 35-80% relative humidity
Audio frequency response
Dynamic range audio
Signal-to-noise ratio video (colour)
More than 43 dB (SP)
Horizontal resolution (colour)
More than 240 lines (VHS, SP), 400 lines (S-VHS/ S-VHS-ET, SP)
Audio output level -6 dBV, less than 1 kOhm
Audio input level -6 dBV, more than 10 kOhm
RF modulated
UHF channel (21-69), 75 Ohm
Video input and output level 1.0 V peak-to-peak, 75 Ohm, terminated
Video TV colour system
Tape speed
Video and Audio heads (helical scanning system)
220-240 V AC, 50/60 Hz
Signal-to-noise ratio audio
More than 90 dB (Hi-Fi sound tracks)
Power consumption
Power consumption in operation
in Power save mode
Video TV system
NTSC Playback on PAL TV
Playback functions
31
18W 15W 15W 13W 13W
3W 3W 3W 3W3W
PAL PAL PAL
PAL PAL
X X X
- -
X X
XX
-
X
- - - -
X
- - - -
SV121
HV61 HV51
MV21
MV16
SV121
HV61 HV51
MV21
MV16
Multifunctional remote control (VCR and Panasonic TV) /
VCR direct controls (main functions)
Switching this appliance into
stand-by mode does not
disconnect it from the mains.
19
Index
RQTD0085-1A F15H05-0
Page Page Page
JET REW 27
3D DNR 4,28 Search forward/backwards 6,27
JET SEARCH 27
Set Top Box 12
AC IN 5,8,9,10
Slow playback 27
MESECAM 15,18,30
AUDIO output 5,9
SQPB 18,30
Mono 15,29
AUDIO settings 28
Stand-by mode 26
Automatic SP/LP selection 22
Start automatic playback 26
Automatic rewinding 27
Still playback 27
Name 15
Automatic shut-down 28
S-VHS ET REC 19,20
NICAM 29
Automatic stop-function 27
S-VHS playback 18
NTSC 29,31
Auto-Start 27
S-VHS REC 19
AV1 OUT 18
S-VIDEO 18
OSD 18
AV1/AV2 (21-pin Scart socket) 5,8
S-VIDEO output 5,9
AV2 18
PAL 15,18,30
AV2 IN 18 Tape counter 7,28
Playback 6,26
Tape length 18
Power consumption 31
Cassette erasure protection 28
Tape remain display 7,20
Power save 19,30
Channel 11,15
Tape speed 20
Power supply 31
Country 8,9,10
TBC, TIME BASE CORRECTION 4,28
Precautions 3
CVC super 4
Time 11
Time limited recording/playback 26
QUICK ERASE 4,28
Date 11
TRACKING/V-LOCK 7,26
Decoder 12,15,18
TV system 18
Remote control 6,7
Digital receiver 19,25
Removing cassettes 28
VCR display 19
Repeat playback 26
EXT 12
VIDEO 18
RF IN/OUT 5,8,9,10
EXT LINK 19,25
VIDEO output 5
RF-coaxial cable 10
Video system 15
Voltage 3
Fine tuning 15
Satellite receiver 12,19,25
VPS/PDC function 22
Scart cable 8
INDEX 27
Search beginning of a recording 6,27
WIDE 18
INTELLIGENT TIMER 7,23
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic NV-HV51 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic NV-HV51 in the language / languages: English as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic NV-HV51

Panasonic NV-HV51 User Manual - German - 32 pages

Panasonic NV-HV51 User Manual - Dutch - 32 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info