136019
51
Zoom out
Zoom in
Previous page
1/68
Next page
Programme Editing
51
11 Press 34 (CURSOR)
to select Start Dubbing
to start editing, and then
press OK.
Editing begins after
the playback unit and
the recording VCR
both rewind their
tapes to the edit start
points.
12 After completing editing,
press 34 (CURSOR)
to select Review, and
then press OK.
The edited sounds are
played back.
To interrupt editing, Preview or Review:
Press EDIT MENU.
To listen to the edited audio after Audio
Dubbing
Press STEREO SELECT during playback and select
STEREO2.
Audio Dubbing
1 PLAYER
RECORDER ¥
Dubbing
in Progress
1
Audio Dubbing
Confirm/Change
Insert a programme
Erase a programme
Preview
Start Dubbing
Review
Timing Adjust
Audio Dubbing
Confirm/Change
Insert a programme
Erase a programme
Preview
Start Dubbing
Review
Timing Adjust
Notes:
Programme Editing can be performed using either the
tape counter or Time code display.
If you attempt to switch to the tape counter display in
order to perform editing after setting the editing points
using the Time code display, the Erase all
programmes screen is displayed.
(The Erase all programmes screen is also displayed
when you change from the tape counter display to the
Time code display.)
Programme editing can not be performed with a video
movie camera that has a 4-digit counter.
After setting a programme, if you attempt to set
another programme in a different editing mode, the
set contents for the previous editing mode remain on
the setting screen. In order to prevent editing errors,
perform the Erase all programmes operation [R53]
whenever you set a programme under a different
editing mode.
Audio Dubbing is not possible in the following
cases:
When the tape in the recording VCR (the NV-DV2000)
is:
Recorded in 16bit audio mode;
Recorded in LP mode;
Blank, or contains a blank portion in the middle
When INPUT SELECT is set to DV1 or DV2.
The Programme Insert and Audio Dubbing functions
require the setting of only three editing points: the in
and out points on the playback unit and the in point on
the recording unit, or the in point on the playback unit
and the in and out points on the recording unit.
If both in and out points are set on both the playback
unit and the recording unit, and the times between the
points do not match, editing stops at the first out point
that is reached.
In order to ensure that the editing operation is
performed properly, the editing points should be set at
least 20 seconds after the beginning of the tape.
The editing operation may not be performed correctly
if the set duration of a programme is less than
4 seconds.
On a video equipment whose Time code display or
tape counter display does not show the frame value,
the area where the frame value is displayed appears
as 00f or it remains blank.
With some units, the frame value may be displayed
when MARK IN or MARK OUT is pressed in steps
5 and 6 even if the unit concerned does not show the
frame value.
Up to d1 second of slight deviation in the specified
edit start/end position can be corrected. See [R54]
for Edit Timing Adjustment.
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic nv dv 2000 ec at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic nv dv 2000 ec in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info