136019
47
Zoom out
Zoom in
Previous page
1/68
Next page
Programme Editing
47
To continue setting programmes:
1 Press EDIT MENU.
2 Press PLAYER.
3 Using 21 (CURSOR), select the programme
number.
The programme number changes each time
these buttons are pressed.
(Up to 20 programmes can be set.
10 programmes can be set on one page; if this
number is exceeded, the display automatically
changes to the next page.)
4 Repeat steps 46 and 9.
10 Press 34 (CURSOR)
to select Start
Assemble to start
editing, and then press
OK.
Editing begins after
the playback unit and
the recording VCR
both rewind their
tapes to the edit start
points.
11 After completing editing,
press 34(CURSOR) to
select Review, and then
press OK.
The edited pictures
are played back.
To interrupt editing or Review:
Press EDIT MENU.
Notes:
Programme Editing can be performed using either the
tape counter or Time code display, but the Time code
display should be used if the units are connected only
by a DV cable.
If you attempt to switch to the tape counter display in
order to perform editing after setting the editing points
using the Time code display, the Erase all
programmes screen is displayed.
(The Erase all programmes screen is also displayed
when you change from the tape counter display to the
Time code display.)
After setting a programme, if you attempt to set
another programme in a different editing operation,
the set contents for the previous editing operation
remain on the setting screen. In order to prevent
editing errors, perform the Erase all programmes
operation [R53] whenever you set a programme
under a different editing mode.
Programme editing can not be performed with a video
movie camera that has a 4-digit counter.
Although Assemble editing can be performed in LP
mode, Insert, Audio Dubbing, and Audio Mixing
cannot be performed with a tape recorded in LP
mode. It is necessary to first copy the tape in SP
mode.
In order to ensure that the editing operation is
performed properly, the editing points should be set at
least 20 seconds after the beginning of the tape.
The editing operation may not be performed correctly
if the set duration of a programme is less than
4 seconds.
On a video equipment whose Time code display or
tape counter display does not show the frame value,
the area where the frame value is displayed appears
as 00f or it remains blank.
With some units, the frame value may be displayed
when MARK IN or MARK OUT is pressed in steps
5 and 6 even if the unit concerned does not show the
frame value.
The Preview function cannot be used with the
Assemble function.
Up to n1 second of slight deviation in the specified
edit start/end position can be corrected. See [R54]
for Edit Timing Adjustment.
Assemble
Confirm/Change
Insert a programme
Erase a programme
Preview
Start Assemble
Review
Timing Adjust
Assemble
[Page1]
1
1 PLAYER RECORDER ¥
Assemble in Progress
Assemble
Confirm/Change
Insert a programme
Erase a programme
Preview
Start Assemble
Review
Timing Adjust
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic nv dv 2000 ec at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic nv dv 2000 ec in the language / languages: English as an attachment in your email.

The manual is 2,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info