453609
54
Zoom out
Zoom in
Previous page
1/60
Next page
Please read these Operating Instructions before using the unit and save for
future reference.
Contents/Inhalt/Table des matières Page/Seite/Page
English instructions 1 – 20
Deutsche Anleitung (1) – (20)
Instructions en français <1> – <20>
This cordless camera is an accessory unit for use with Panasonic Digital
Cordless Phone:
KX-TG9120/KX-TG9140/KX-TG9150
You must register this cordless camera with your base unit before it can
be used.
Cordless Camer
a
Model No. KX-TGA914E
X
Operating Instructions
Indoor Use Only
TGA914EX_1(e).book Page 1 Tuesday, August 8, 2006 2:21 PM
Table of Contents
2
Introduction
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessory information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Preparation
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Setting up the cordless camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Symbols used in these operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Registering the cordless camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Camera Monitoring
Camera monitoring using a handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Useful Information
Wall mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TGA914EX_1(e).book Page 2 Tuesday, August 8, 2006 2:21 PM
Introduction
3
Introduction
Thank you for purchasing the cordless camera.
For your future reference
Attach or keep original receipt to assist with any repair under warranty.
Feature highlight
Camera monitoring using the handset
Important:
L In these operating instructions, the term “handset” is used to refer to the KX-TGA910EX.
You can monitor the room where the cordless camera is located when:
you access the cordless camera using the handset (page 11).
the cordless camera pages the handset when it detects sound (page 12).
the cordless camera user pages the handset using the call button (page 12).
Serial No. (found on the bottom of the unit)
Date of purchase
Name and address of dealer
TGA914EX_1(e).book Page 3 Tuesday, August 8, 2006 2:21 PM
Introduction
4
Accessory information
Included accessories
No. Accessory item Quantity
1 AC adaptor
Part No. PQLV209CE
1
2 Wall-mounting adaptor 1
3 Call button 1
123
TGA914EX_1(e).book Page 4 Tuesday, August 8, 2006 2:21 PM
5
Introduction
Important information
General
L Use only the AC adaptor included with this
product, noted on page 4.
L Do not connect the AC adaptor to any AC
outlet other than a standard 220–240 V
AC outlet.
L This product should not be used near
emergency/intensive care medical
equipment and should not be used by
people with pacemakers.
L Care should be taken that objects do not
fall onto, and liquids are not spilled into,
the unit. Do not subject this product to
excessive smoke, dust, mechanical
vibration or shock.
Environment
L Do not use this product near water.
L This product should be kept away from
heat sources such as radiators, cookers,
etc. It should also not be placed in rooms
where the temperature is less than 5 °C or
greater than 40 °C.
L The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the product and is
easily accessible.
Warning:
L To prevent the risk of electrical shock, do
not expose this product to rain or any
other type of moisture.
L Unplug this product from power outlets if it
emits smoke, an abnormal smell, or
makes unusual noise. These conditions
can cause fire or electric shock. Confirm
that smoke has stopped emitting and
contact an authorised service centre.
Routine care
L After cleaning away the dust on the lens,
wipe the lens with a cotton bud.
Conditions for using the cordless
camera
L The cordless camera is intended for
indoor use only. Prolonged exposure to
direct sunlight or halogen light may
damage the camera lens.
L Use the cordless camera in a bright place
such as under daylight or a well-lit room.
L Do not use the cordless camera in the
following places:
near incandescent lamps.
near any electrical appliance that emits
a strong radio signal.
where the subject of the picture is
against a light source or in front of a
mirror.
in places where temperature varies
greatly, such as near an air conditioner
or heater.
any place exposed to oil or steam such
as a kitchen.
where an object such as glass can
cause temperature change due to
reflection.
L When using the cordless camera, please
take into consideration the rights of others
with regard to privacy.
TGA914EX_1(e).book Page 5 Tuesday, August 8, 2006 2:21 PM
Preparation
6
Controls
Understanding the cordless camera indicator
The cordless camera indicator shows the status as follows.
A Antenna
B Camera lens
C MIC (Microphone)
D Call button
E Indicator
F DIP switches
G Speaker
H PROG. (Program)
Status Description
Red (flashing rapidly) L The cordless camera is not registered. Register the
cordless camera (page 10).
L The cordless camera is out of range. Locate the cordless
camera near the base unit.
Yellow-green L The cordless camera is registered and in standby mode.
Yellow-green (flashing) L The camera sensor is responding and the cordless camera
is paging the handset.
L The cordless camera is connected and sending live images
to the handset.
H
G
E
A
B
C
D
F
TGA914EX_1(e).book Page 6 Tuesday, August 8, 2006 2:21 PM
Preparation
7
Setting up the cordless camera
Connecting the AC adaptor and the call button
Connect the AC adaptor cord by pressing the plug firmly (A). Connect the call button cord
until it clicks into the unit (B).
L Use only the included AC adaptor.
Note:
L When the AC adaptor is connected, the indicator lights in red then starts flashing.
L The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel
warm during use.)
L The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do
not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor
may cause it to become disconnected.
(220–240 V, 50 Hz)
B
A
Hooks
TGA914EX_1(e).book Page 7 Tuesday, August 8, 2006 2:21 PM
Preparation
8
Adjusting the cordless camera lens angle
Aim the camera lens by pushing the tab (A) and rotating the lens up or down.
L Using the handset, confirm that the area you want to monitor from the cordless camera is
displayed (page 11).
Note:
L Do not touch the camera lens (page 6).
A
Approx.
40°
Approx.
40°
TGA914EX_1(e).book Page 8 Tuesday, August 8, 2006 2:21 PM
Preparation
9
Setting the DIP switches
You can set the following functions by using DIP switches 2 and 3.
DIP switch 1 is not used for any settings.
Slide each switch with a pointed object such as a pen as necessary.
*1 Slide the switch down.
Displaying the image upside down (DIP switch 2)
To turn the camera image upside down, set to OFF. This feature is useful when you mount the
cordless camera upside down (page 15).
Selecting the cordless camera speaker volume (DIP switch 3)
If you want to lower the speaker volume, set to OFF (LOW).
DIP switch Function ON (default) OFF
*1
1–
2 Image orientation Normal Upside down
3 Speaker volume Normal Low
1
ON
23
DIP switches
(Default position: ON)
OFF*1
TGA914EX_1(e).book Page 9 Tuesday, August 8, 2006 2:21 PM
10
Preparation
Symbols used in these
operating instructions
Registering the cordless
camera
Register the cordless camera to a KX-
TG9120/KX-TG9140/KX-TG9150 base unit.
1 Base unit:
Press and hold {x} on the base unit for
about 3 seconds, until the registration
tone sounds.
2 Camera:
Press PROG. (program) on the back side
of the cordless camera with a pointed
object such as a pen until a beep sounds.
L When registration is completed
successfully, the cordless camera
beeps and the indicator stops flashing
red but remains lit in yellow-green
(page 6).
L If all registered handset start ringing in
step 2, press {x} to stop. Start again
from step 1.
Cancelling the cordless camera
Using a handset registered to the same
base unit, you can cancel the registration of
a registered cordless camera.
1 J (centre of joystick) i L i L
2 Enter “335”.
3 Cancel Handseti L
4 Select the cordless camera you want to
cancel. i t
L A Q is displayed with the selected item.
L To cancel a selected item, select it
again. i t
5 L iYesi L
L Please Wait...” will be displayed
and a long beep will sound.
6 {ih}
Symbol Meaning
J Press J (centre of joystick).
i Proceed to the next operation.
L Press L (centre of joystick).
“ ” Select the words in quotations
shown on the display (e.g.,
Cancel Handset”) by
pushing the joystick up or
down.
TGA914EX_1(e).book Page 10 Tuesday, August 8, 2006 2:21 PM
11
Camera Monitoring
Camera monitoring using
a handset
With a handset, you can monitor the image
and sound of the room where the cordless
camera is located. The monitored camera
does not ring, allowing you to easily monitor
a baby’s room, for example, from different
areas of the house.
Important:
L Before you start monitoring, confirm that
the camera lens of the cordless camera
has been adjusted to the correct angle.
L Only 1 person can access the cordless
camera at a time.
L A refreshed image taken by the cordless
camera is displayed every few seconds.
The displayed image is not a moving
picture.
L While monitoring a cordless camera,
other users cannot make an intercom call
or transfer a call.
L The monitoring connection is
automatically cancelled after 10 minutes.
L While monitoring you cannot place the
handset on the base unit or charger. The
monitoring connection will be cancelled.
L The cordless camera may not page
handsets in the following conditions:
when other users are on an intercom or
conference call.
when electrical interference is emitted
from electrical devices.
while you are on a call with the handset.
(In this case you will hear 2 tones and
z will flash on the handset.)
L You cannot make a monitoring connection
via a DECT repeater.
Monitoring the cordless camera
from a handset
1 {INT}
2 Select the desired cordless camera. i
P/{C}/{s}
3 Speak to the cordless camera user if
necessary.
OR
To mute your sound output, press {C/T}
if necessary.
4 When you finish monitoring, press
{ih} or place the handset on the base
unit or charger.
Adjusting receiver/speaker volume
Push the joystick up or down while
monitoring.
Talking to the paged party using the
cordless camera
When the cordless camera is paged from a
handset, the cordless camera does not ring
and the speakerphone is turned on. You can
talk to the handset user. Speak clearly into
the MIC.
Handset
TGA914EX_1(e).book Page 11 Tuesday, August 8, 2006 2:21 PM
12
Camera Monitoring
Handset display item for camera
monitoring
Paging the handsets from the
cordless camera
The cordless camera can page handsets
when it detects sound or by pressing its call
button. Then the answering handset user
can monitor live images from the cordless
camera.
Important:
L Only registered handsets can be paged
from the cordless camera. The base unit
cannot be paged.
L If a handset is paged by the cordless
camera during a call, 2 tones sound and
z flashes on the handset. To monitor the
cordless camera from the handset, press
{ih}, then press {s}.
L Auto intercom feature cannot be used
when paged by a cordless camera.
Paging using the camera audio sensor
Important:
L To use the audio detection feature of the
cordless camera, turn the audio detection
sensitivity to on (page 13).
1 Camera:
The camera detects sound.
L The camera produces a camera tone
and pages the handsets for 1 minute.
2 Handset:
Press {s} to answer the page.
L You can monitor the room where the
camera is located.
3 Handset:
To mute your sound output, press {C/T}
if necessary.
4 Handset:
When you finish monitoring, press
{ih} or place the handset on the base
unit or charger.
Paging using the cordless camera call
button
1 Cordless camera:
Press the call button.
L The cordless camera produces a
camera tone and pages the handsets
for 1 minute.
L To stop paging, press the call button
again.
2 Handset:
Press {s} to answer the page.
L You can monitor the room where the
cordless camera is located.
3 Cordless camera:
When the handset user answers, speak
clearly into the MIC.
4 Handset:
Displayed
item
Meaning
Example:
8
The handset is connected
to the cordless camera.
When flashing:
The cordless camera is
paging the handset. (It
detects sound or its call
button is pressed.)
TGA914EX_1(e).book Page 12 Tuesday, August 8, 2006 2:21 PM
13
Camera Monitoring
When you finish monitoring, press
{ih} or place the handset on the base
unit or charger.
Useful settings while camera
monitoring
With a handset, you can set the camera
settings while monitoring.
Adjusting the display brightness
There are 6 levels.
1 Start monitoring (page 11).
2 Press B repeatedly to adjust the
brightness.
Note:
L When you finish monitoring, the setting is
reset to the default.
Selecting image zoom
1 Start monitoring (page 11).
2 Press A to zoom in on the image.
L To return to the original view, press
A again.
Setting the audio detection sensitivity
The cordless camera features a sensor that
detects human voices such as a baby cry.
Sounds other than human voices may be
difficult to detect. To use this feature, confirm
that the cordless camera is located in a
place where it can easily detect voices.
Once the sensor has detected sound, the
cordless camera pages the handset.
There are 3 levels. The default setting is
“off”.
1 Start monitoring (page 11).
2 v
3 To turn the feature on, push the joystick
up.
Push the joystick up or down to select the
desired sensitivity.
L To turn this feature off, push down the
joystick repeatedly.
4 L
Note:
L When you turn this feature off, the
cordless camera cannot detect sound
(page 12).
L To set the appropriate level, test the
sensor of the camera from the handset
beforehand.
TGA914EX_1(e).book Page 13 Tuesday, August 8, 2006 2:21 PM
Informations utiles
<14>
Montage mural
La caméra sans fil peut être installé via le montage standard ou le montage inversé.
ATTENTION :
L
Montez la caméra sans fil sur un emplacement stable sur lequel l’appareil peut être pris en charge de
manière appropriée lors de son installation.
L
L’adaptateur secteur doit être branché sur une prise secteur verticale ou montée au sol. Ne branchez
pas l’adaptateur secteur à une prise secteur montée au plafond, car il risque de se débrancher sous
l’effet de son poids.
L
Ne montez pas la caméra sans fil sur un matériau souple. Il pourrait chuter, se casser ou
provoquer des blessures
.
L
Ne montez pas la caméra sans fil sur une plaque de plâtre, du béton cellulaire léger autoclavé, un
bloc en béton, du contreplaqué d’une épaisseur inférieure à 25 mm, etc.
L
Ne tirez pas sur le fil du bouton d’appel après avoir fixé la caméra sans fil au mur.
L
Une fois la caméra sans fil fixé au mur, parlez fort et clairement dans le micro pour communiquer avec
l’utilisateur du combiné.
Raccordement de l’adaptateur à montage mural
A
Faites glisser la caméra sans fil dans l’adaptateur à montage mural dans le sens de la flèche jusqu’à
ce qu’il se mette en place.
B
Placez le fil du bouton d’appel dans le trou situé sur le côté de l’adaptateur à montage mural et
insérez la petite fixation du fil dans le trou.
C
Tournez-la légèrement et faites-la glisser pour la mettre en place.
D
Attachez le fil du bouton d’appel au crochet de l’adaptateur à montage mural.
TGA914EX_1(fr).book Page 14 Monday, July 31, 2006 6:04 PM
54


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic KX-TGA914EX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic KX-TGA914EX in the language / languages: English, German, French as an attachment in your email.

The manual is 2,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info