463423

Panasonic KX-TCD150FXC Manual

42
Zoom out
Zoom in
Previous page
1/77
Next page
15.3. Telephone Line Interface
<Function>
·
Bell signal detection
·
Clip signal detection
·
ON/OFF hook circuit
·
Audio circuits
Bell & Clip (: Calling Line Identification Presentation: Caller ID) signal detection:
In the standby mode, Q2 is open to cut the DC loop current and decrease the ring load.
When ring voltage appears at the TP3 (A) and TP40 (B) leads (when the telephone rings), the signal is transferred as follows;
·
A → C4 → R2 → R29 → IC2 (DLP) [BELL & CLIP]
·
B → C3 → R1 → R30 → IC2 (DLP) [BELL & CLIP]
ON/OFF hook circuit:
In the standby mode, Q2 is open, and connected as to cut the DC loop current and to cut the voice signal. The unit is
consequently in an off-hook condition.
When IC2 detects a ring signal or press the TALK Key onto the handset, Q3 turns on and then Q2 turns on, thus providing an
off-hook condition (active DC current flow through the circuit) and the following signal flow is for the loop current.
·
A → D2 → Q2 → R8 → Q6 → R19 → R20 → D2→ B[OFF HOOK]
Audio circuits:
Refer to SIGNAL ROUTE (P.46).
15.4. Transmitter/Receiver
Base Unit and Handset mainly consist of RF Module and DECT BBIC.
Base Unit and Handset transmit/receive voice signal and data signal through the antenna on carrier frequency.
Signal Path:
*Refer to SIGNAL ROUTE (P.46).
15.4.1. Transmitter Block
The voice signal input from the TEL LINE interface goes to RF Module (IC3) through DECT BBIC (IC2) as shown in BLOCK
DIAGRAM (BASE UNIT) (P.39)
The voice signal passes through the analog part of IC2 where it is amplified and converted to a digital audio stream signal. The
burst switch controller processes this stream performing encryption and scrambling, adding the various other fields to produce
the GAP (Generic Access Profile) standard DECT frame, assigning to a time slot and channel etc.
In IC3, the carrier frequency is changing, and frequency modulated RF signal is generated and amplified, and radiated from
antenna. Handset detects the voice signal or data signal in the circuit same as the following explanation of Receiver Block.
15.4.2. Receiver Block
The signal of 1.9 GHz band (1.881792 GHz ~ 1.897344 GHz) which is input from antenna is input to IC3 as shown in BLOCK
DIAGRAM (BASE UNIT) (P.39).
In IC3, the signal of 1.9 GHz band is demodulated, and goes to IC2 as GAP (Generic Access Profile) standard DECT frames.
It passes through the decoding section burst switch controller where it separates out the frame information and performs de-
encryption and de-scrambling as required. It then goes to the DSP section where it is turned back into analog audio. This is
amplified by the analog front end, and goes to the TEL LINE Interface.
15.5. Pulse Dialling
During pulse dialing the hookswitch (Q4,Q5) is used to generate the pulses using the HOOK control signal, which is set high
during pulses. To force the line impedance low during the “pause” intervals between dial pulses, the PULSE_DIAL signal turns
on Q12.
42
KX-TCD150FXB / KX-TCD150FXC / KX-TCD152FXB / KX-TCA115EXB / KX-TCA115EXC
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic KX-TCD150FXC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic KX-TCD150FXC in the language / languages: English as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info