When an error is detected right after the unit is turned on or during the operation, the occurrence of the error is notified in the camera image screen of the
LCD monitor or by the tally lamp. Deal with the error by following the indications.
≥The tally lamp is available when the handle unit ( supplied, optional) is attached.
Cases indicated by error messages
System error
Warning
Screen display
DescriptionBehavior and cause
Camera image screen
[SYSTEM ERROR]An error in the standard signal or communication error has
occurred.
The tally lamp and all of the card access lamps (orange)
flash 4 times each second, and an alarm sounds.
≥Press the power button to turn off the power.
Screen display
DescriptionBehavior and cause
Camera image screen
[LOW BATTERY]Remaining battery level is insufficient.The tally lamp and all of the card access lamps (orange)
flash 4 times each second, and an alarm sounds.
The power status display becomes , and it will flash
once every second in red.
≥The power is turned off in approximately 5 seconds.
≥Replace with a fully charged battery, or connect the AC
adaptor.
[HIGH TEMPERATURE]Displayed when the internal temperature of the main unit
has risen above assumed.
The tally lamp and all of the card access lamps (orange)
flash 4 times each second, and an alarm sounds.
≥The power is turned off in approximately 5 seconds.
≥Turn on the power again and check recording and
playback operations. If the problem persists, consult the
dealer.
[FAN STOPPED]The fan has stopped.≥The power turns off approximately 1 minute later.
≥Stop the use immediately when the fan has stopped, and
consult the dealer.
≥If the fan has stopped, temperature of the unit will rise.
Therefore, do not use the unit for a long period of time.
[REC WARNING]An error of the recording data has occurred during
recording, and the recording has stopped.
The tally lamp and all of the card access lamps (orange)
flash 4 times each second, and an alarm sounds.
≥Recording is stopped.
It has tried to record exceeding the maximum number of
clips during recording.
The tally lamp and all of the card access lamps (orange)
flash 4 times each second, and an alarm sounds.
≥Recording is stopped.
≥[REC WARNING] [<OVER MAX NUM. OF CLIPS>] is
displayed in the warning display field of the STATUS
screen for the mode check.
≥Replace the memory card or delete unnecessary clips.
[CARD ERROR <SLOT 1>]/
[CARD ERROR <SLOT 2>]
A data error caused by the memory card has occurred
during recording or playback.
≥When it was recording
The tally lamp and all of the card access lamps (orange)
flash 4 times each second, and an alarm sounds.
Recording is stopped.
The memory card where the error has occurred is write
protected after recording stops. Replace the memory card
in the card slot where the error has occurred.
≥When it was playing back
Playback is stopped.
[END]
(Memory card status display)
The remaining recording capacity of the memory card has
exhausted during recording.
The tally lamp and all of the card access lamps (orange)
flash 4 times each second, and an alarm sounds.
≥Recording is stopped.
≥Replace the memory card or delete unnecessary clips.
(Once every second, flash in red)
Battery is almost consumed.Tally lamp flashes once every second.
≥The current operation will continue.
≥Replace with a fully charged battery, or connect the AC
adaptor.
Remaining recording capacity display
of the memory card
(Flashes once every second during
recording)
The remaining recording capacity of the memory card is
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Panasonic HC-X1500 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Panasonic HC-X1500 in the language / languages: English as an attachment in your email.
The manual is 9,35 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
