502409

Panasonic EY7201 Manual

4
Zoom out
Zoom in
Previous page
1/52
Next page
– 6 – – 7 –
LED light How to use the belt hook
CAUTION:
To eliminate excessive temperature
increase of the tool surface, do not oper-
ate the tool continuously (using two or
more battery packs consecutively.) Tool
needs cool off time before switching to
another pack.
CAUTION:
To prevent damage, do not operate
Forward/Reverse lever until the bit
comes to a complete stop.
1. Set the belt hook at storing position.
2. Loosen the screw turning it counter-
clock-wise, using a coin or a flat blade
screw driver.
3. Take out the belt hook and insert into
the other side of the slot on the main
unit.
4. Fasten the screw firmly, turning it clock-
wise.
The belt hook can be taken out from the
main unit only when it is at storing position.
To change the belt hook
location side
The belt hook can be attached to either
side of the unit.
Switch and Forward/Reverse
lever Operation
Forward Rotation Switch
Operation
1. Push the lever for forward rotation.
2. Depress the trigger switch slightly to
start the tool slowly.
3. The speed increases with the amount
of depression of the trigger for efficient
tightening of screws. The brake oper-
ates and the bit stops immediately
when the trigger is released.
4. After use, set the lever to its center po-
sition (switch lock).
Reverse Rotation Switch
Operation
1. Push the lever for reverse rotation. Check
the direction of rotation before use.
2. Depress the trigger switch slightly to
start the tool slowly.
3. After use, set the lever to its center po-
sition (switch lock).
CAUTION:
The built-in LED light is designed to illu-
minate the small work area temporarily.
Do not use it as a substitute for a regular
flashlight, since it does not have enough
brightness.
Depress the trigger switch, then LED light
turns on. When the trigger switch is
released, the light turns off automatically.
The light illuminates with very low current,
and it does not adversely affect the perfor-
mance of the driver during use or its bat-
tery capacity.
WARNING:
• Be sure to attach the belt hook
securely to the main unit with the screw
firmly fastened. When the belt hook is
not firmly attached to the main unit, the
hook may depart and the main unit
may fall.
This may result in an accident or injury.
• Be sure to attach the belt hook firmly
and securely onto a waist belt or other
belt. Pay attention to the unit not
slipping off from the belt.
This may result in an accident or injury.
• When the main unit is held by the belt
hook, avoid jumping or running with it.
Doing so may cause the hook to slip
and the main unit may fall.
This may result in an accident or injury.
• When the belt hook is not used, be
sure to return it to the storing position.
The belt hook may catch on something.
This may result in an accident or injury.
• When the unit is hooked onto the waist
belt by the belt hook, do not attach
driver bits to the unit.
A sharp edge object, such as a drill bit,
may cause injury or an accident.
To set the belt hook angle
position
1. Slide the belt hook lock lever # and
hold it to unlock the belt hook.
2. Pull the belt hook from
storing position $ and
set it as desired angle.
3. Release the belt hook
lock lever to lock the
angle of belt hook.
4. Make sure the belt hook is firmly locked
%. Also make sure the belt hook is firmly
locked into position.
• The belt hook cannot
be locked in this posi-
tion. Firmly lock it into
position before use.
To return the belt hook to the storing
position, Follow step 1. and 2. above, then
lower the belt hook.
To secure the lock, follow 3 and 4 above.
Forward Reverse
Switch lock
Caution: DO NOT STARE INTO BEAM.
This product has the built-in LED light.
This product is classfied into “Class 1 LED
Product” to EN 60825-1.
CLASS 1 LED PRODUCT

… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic EY7201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic EY7201 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,88 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info