502403
6
Zoom out
Zoom in
Previous page
1/36
Next page
6
Main switch (ON/OFF)···(E)
Push the upper half of the switch for forward
( ) rotation, or the lower half for reverse
( ) rotation.
(Refer figure 5)
Speed selector switch···(C)
To suit the application of this tool, two
different rotational speeds are available.
Depending upon use, either the high or low
speed should be selected.
LOW
HIGH
200min
-1
(RPM)
400min
-1
(RPM)
strong torque
less torque
CAUTION: Check rotational speed selection
before operating this tool.
(Refer figure 6)
Main switch lock···(D)
After use, set the main switch lock at the lock
position to prevent accidental operation.
(Refer figure 7)
Battery pack (EY9021/EY903)···(F)
1. Press the battery pack release buttons on
both sides and pull the pack away from the
tool.
2. Carge the battery pack using the battery
charger.
3. After the charging has been completed,
remove the battery pack from the charger
and connect it to the tool. Disconnect the
charger from the power source when not in
use.
Battery pack life
The rechargeable batteries have a limited life.
If operation time becomes extremely short
after recharging, replace the battery pack with
a new one.
NOTE: Use under extremely hot or cold
conditions will reduce operating
capacity per charge.
Battery Recycling
For environmental protection and recycling of
materials, be sure that it is disposed of at an
officially assigned location, if there is one in
your country.
Battery charger (EY0020/RE503)···(H)
NOTE: When you charge the battery pack for
the first time, or after prolonged
storage, charge it for about 24 hours to
bring the batteries up to full capacity.
1. Press the battery pack release button and
pull the pack away from the tool.
(Refer figure 8)
2. Plug the charger into the power source.
3. Insert the battery pack firmly into the
charger.
(Refer figure 9)
4. During charging, the charging lamp will be
light up.
When the charge is completed, an internal
electronic switch will automatically be
triggered to prevent overcharging.
If the charging lamp does not light, check
to determine whether the contacts are
clean and the battery pack is inserted
completely.
5. When charging is completed, the charging
lamp will go out.
6. Avoid charging at temperatures below 0°C
above 40°C.
7. After charging has been completed,
remove the battery pack from the charger
and reinsert it into the tool.
(Refer figure 10)
8. If the charging lamp does not turn on
immediately afater the chager has been
plugged in, or if after 2 hours of charging
the lamp does not go off, consult an
authorized dealer for checking.
NOTE: The battery pack EY9021 can be
charged by 15 min. charger EY0202
using adapter EY0890.
CAUTION: Do not use power source from
an engine generator.
Do not cover vent holes on the
charger.
Unplug the charger when not in
use.
P06-08(6220EN) 05.05.02 10:18 ページ 6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic EY6220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic EY6220 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info