78911

Panasonic EY 6409 Manual

6
Zoom out
Zoom in
Previous page
1/59
Next page
— 6 —
Read the Safety Instructions booklet
and the following before using.
I. ADDITIONAL
SAFETY RULES
1) Be aware that this tool is always in an operat-
ing condition, since it does not have to be
plugged into an electrical outlet.
2) When drilling or driving into walls, floors, etc.,
“live” electrical wires may be encountered.
DO NOT TOUCH THE CHUCK OR ANY
FRONT METAL PARTS OF THE TOOL! Hold
the tool only by the plastic handle to prevent
electric shock in case you drill or drive into a
“live” wire.
3) If the bit becomes jammed, immediately turn
the main switch off to prevent an overload,
which can damage the battery pack or motor.
Use reverse motion to loosen jammed bits.
4) Do NOT operate the Forward/Reverse lever
when the main switch is on. The battery will
discharge rapidly and damage to the unit
may occur.
5) During charging, the charger may become
slightly warm. This is normal. Do NOT charge
the battery for a long period.
6) Use only a dry, soft cloth to wipe the unit. Do
NOT use a damp cloth, thinner, benzine, or
other volatile solvents for cleaning.
7) When storing or carrying the tool, set the Forward/
Reverse lever to the center position (switch lock).
8) Do not strain the tool by holding the speed
control trigger halfway (speed control mode)
so that the motor stops.
9) Do not operate the speed selector switch
(LOW-HIGH) while pulling on the speed con-
trol trigger. This can cause the rechargeable
battery to wear quickly or damage the inter-
nal mechanism of the motor.
10) Young children should be supervised to
ensure that they do not play with the appli-
ance.
11) Wear ear protectors when using the tool for
extended periods.
II. ASSEMBLY
Attaching or removing bit
Note: When attaching or removing a bit, be sure
to set the Forward/Reverse lever to its cen-
ter position (switch lock).
This tool is equipped with a keyless drill chuck.
1) Attachment
Insert the bit and turn the lock collar clock-
wise (looking from the front) to tighten. (Fig.
2)
2) Removal
Turn the lock collar counterclockwise (looking
from the front), then remove the bit. (Fig. 3)
3) Storage
Keep the bit in bit holder when not in use.
Remove the battery pack to expose the bit
storage compartment inside the handle hous-
ing.
Bits up to 50 mm (1-31/32 inch) long can be
stored here. (Fig. 4)
Note: If excessive play occurs in the chuck,
secure the drill in place and open the
chuck claws by turning the lock collar and
tighten the screw (left-handed screw)
with a screwdriver by turning it counter-
clockwise (viewed from the front). (Fig. 5)
Attaching or removing battery pack
1. To connect the battery pack:
Insert the battery pack. It snaps into place to
indicate proper connection.
2. To remove the battery pack:
Press the two buttons on the sides of the bat-
tery pack. Slide the battery pack out of the tool
body.
1
2
EY6405(EU).book Page 6 Wednesday, June 15, 2005 7:14 PM
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic EY 6409 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic EY 6409 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info