Hold the shaver at a right angle (90°)
to your skin (see fig. 3). Start out
shaving by applying gentle pressure
to your face. Stretch your skin with
your free hand and move the shaver
back and forth in the direction of your
beard. You may gently increase the
amount of pressure as your skin be-
comes accustomed to this shaver.
Applying excessive pressure does
not provide a closer shave.
System outer foil
(see fig. 4)
System outer foil has a slit blade (a)
between 2 foils (b). They move up
and down independently to follow the
contours of your face.
The slit blade catches and cuts
longer and lying hairs easily.
For wet shaving
Put a thin layer of shaving foam
on your face which works as a lu-
bricator. Shaving foam is the most
suitable among many other shav-
ing aids (gel, soap, cream, etc.).
Do not put a thick layer of shaving
foam as it may affect shaver’s per-
formance. If the shaving head is
clogged with foam, simply rinse
it under running water.
Using the trimmer
(see fig. 5)
Slide the trimmer handle up to open
the trimmer.
Place the trimmer at a right angle to
your skin and move it downward to
trim sideburns.
Cleaning your shaver
(see fig. 6)
Warning – To prevent electric
shock or personal injury, discon-
nect the power cord from the
shaver before cleaning with water.
For cleanliness and convenience, we
recommend that you clean your
shaver with water and a liquid hand
soap. Regular cleaning will keep your
shaver in good condition while pre-
venting odors or bacteria from devel-
oping, and maintain the cutting per-
formance.
With the system outer foil in place,
apply some hand soap onto the outer
foil.
Turn the shaver on and pour some
water over the outer foil.
After about 10-20 seconds, turn the
shaver off.
Remove the foil frame and clean
it with running water.
Wipe off any moisture from the
shaver with a dry cloth and remove
the protective cap to allow the sys-
tem outer foil to dry completely.
Brush cleaning
Squeeze the foil frame release but-
tons and lift the foil frame upward to
remove it (see fig. 8). Remove the in-
ner blades one at a time by grasping
it firmly at both ends and pulling it
straight away from the shaver. Clean
the outer foils, the shaver body and
the trimmer with the long brush (see
fig. 9). Clean the inner blades with
the short brush by moving it in the
direction in fig. 10 (A). Do not move
the brush in the direction in fig. 10
(B), as it will damage the inner blade,
and its cutting performance. Do not
use the short brush to clean the outer
foils.
Replacing shaving head
components
It is recommended that you replace
the system outer foil at least once a
year and the inner blade at least once
every 2 years to maintain your
shaver’s cutting performance.
Replacing the system outer foil
(see fig. 7)
Squeeze the system outer foil re-
lease buttons and lift the system
outer foil upward to remove it. To in-
sert the new system outer foil, press
down until it snaps into place.
Replacing the inner blades
(see fig. 8)
Squeeze the foil frame release
buttons and lift the foil frame
upward to remove it. Remove the
inner blade one at a time by
grasping it firmly at both ends
and pulling straight away from
the shaver.
Do not touch the metal parts of inner
blades.
To insert the new inner blade, hold
the blade one at a time at both ends
and press downward until it snaps
into the shaver.
For environmental protec-
tion and recycling of
materials
This shaver contains Nickel-Metal
Hydride batteries.
Please make sure that the batteries
are disposed of at an officially as-
signed location, if there is one in your
country.
How to remove the built-in
rechargeable battery before
disposal of the shaver
(see fig. 11)
WARNING:
Do not attempt to replace the bat-
tery for the purpose of reusing the
shaver. This could result in the risk
of fire or electric shock.
The battery in this shaver is not
intended to be replaced by con-
sumers. However, the battery
may be replaced at an authorized
service center. The procedure
described below is intended only
for removal of the rechargeable
battery for the purpose of proper
disposal.
1. Disconnect the power cord from
the shaver when removing the
battery.
2. Remove the bottom cover screw
(a).
3. Remove the bottom cover (b).
4. Slide the side panels (c) and re-
move it.
5. Remove the six housing screws
(d).
6. Remove the trimmer handle (e).
7. Remove the two screws (f).
