603083
29
Zoom out
Zoom in
Previous page
1/36
Next page
Reference
29
SQT0126
The TV screen turns black.
¾ In the following cases, HDMI authentication
takes place and a black screen is displayed:
When “24p Output” is set to “On”.
[BDT260] [BDT161] [BDT160] When the display
is switched between 2D and 3D images.
This unit does not recognize the USB
connection correctly.
¾ Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
¾ USB devices may not be recognized by this
unit when connected using the following :
a USB hub
¾ If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
[For[the[Middle[East,[South[East[Asia[and[India]
¾ When you connect a USB HDD, use the left
USB port (USB1). (> 13)
The images from this unit do not appear on
the TV.
Picture is distorted.
¾ An incorrect resolution is selected in “HDMI
Video Format”. Reset the setting as follows:
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
Set the item again. (> 24)
When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD
®
audio are not output properly,
select “Yes” in “Default Settings” (> 27) and
make proper settings.
Video is not output in high-definition.
¾ Confirm that “HDMI Video Format” in the
Setup menu is set properly. (> 24)
a USB extension cable other than the
supplied with the Wireless LAN Adaptor
DY-WL5 (optional)
Picture
POWER LED starts to flash.
3 Press [8] and the blue button on the remote
control at the same time for more than
5 seconds.
¾ The unit and TV are using different video
systems.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
POWER LED starts to flash, and “00RET”
is displayed on the screen.
3 Press [1] (right) repeatedly on the remote
control until “05P/N” is displayed on the
screen.
4 Press and hold [OK] for more than
5 seconds.
The system switches from PAL to NTSC or
vice versa.
¾ PAL discs cannot be correctly viewed on an
NTSC TV.
¾ [BDT260] [BDT161] [BDT160] When “3D
BD-Video Playback” in the Setup menu is set
to “Automatic”, images may not be output
depending on the connection method. After
removing the disc from this unit, select “Set
before play” in the Setup menu, and select
“2D Playback” in the setup screen displayed
when playing 3D discs. (> 25)
3D video is not output.
[BDT260] [BDT161] [BDT160]
¾ Connect to a full high-definition TV.
¾ Is there a non-3D compatible amplifier/
receiver connected between this unit and a
TV? (> 10)
¾ Are the settings on this unit and the TV
correct? (> 17)
¾ Is the amplifier/receiver that is connected
between this unit and TV on?
¾ Depending on the connected TV, the video
being played back might switch to 2D video
due to changes in resolution etc. Check the
3D setting on the TV.
DMP-BDT260&161&160&BD91&81_EBGNGCGAGW-SQT0126_eng.book 29 ページ 2014年2月28日 金曜日 午前10時44分
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic DMPBDT160GW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic DMPBDT160GW in the language / languages: English as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info