456584
38
Zoom out
Zoom in
Previous page
1/48
Next page
RQT9243 or RQT9350
38
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart
do not solve the problem, refer to “Customer Services Directory” on page 42 if you reside in the U.S.A., or refer to “Product information” on page 44
if you reside in Canada.
The following do not indicate a problem with this unit:
Regular disc rotating sounds.
Image disturbance during search.
To reset this unit Page
Operation
To restore the unit if it
freezes due to one of the
safety devices being
activated
Press and hold [POWER Í/I] on the main unit for 3 seconds. (The settings
remain unchanged.)
To return all settings to the
factory preset
Select “Yes” in “Restore Default Settings” in the Setup menu.
This returns all values in the Setup menu and the on-screen menu, except for
“Remote Control Code”, “On-screen Language”, “IP Address/DNS Settings”,
“Proxy Server Settings”, “DVD-Video Ratings” and “BD-Video Ratings” to the
default settings.
33
To return to the factory
preset
(No setting)
Reset the unit as follows:
1Press [POWER Í/I] on the unit to turn off the unit.
2 Press and hold [;], [POWER Í/I] and [< OPEN/CLOSE] on the unit at the
same time for more than 5 seconds until “HELLO” is displayed on the unit.
3 The power will turn on and then turn off.
Cannot operate the
television or amplifier/
receiver.
The remote control doesn’t
work properly.
Change the manufacturer code of the remote control. In some cases, even if you
change the code, the remote control may not be operated depending on the type
of the televisions or receivers.
It may be necessary to set the manufacturer code or the remote control code
again after changing the batteries for remote control.
The remote control and main unit are using different codes. Change the code on
the remote control.
The batteries are depleted. Replace them with new ones.
16
16, 33
33
5
The unit is on but cannot be
operated.
Confirm the correct drive is selected.
One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1Press [POWER Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [POWER Í/I] on the main
unit for about 3 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC power supply cord, wait one minute, then
reconnect it.
2Press [POWER Í/I] on the main unit to switch it on. If the unit still cannot be
operated, consult the dealer.
Condensation has formed. Wait 1 to 2 hours for it to evaporate.
19
Play fails to start even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
Insert the disc correctly with the label facing up.
The disc is dirty.
You tried to play a blank disc or unplayable disc on this unit.
[DivX]: If playing DivX VOD content, refer to the homepage where you purchased
it.
19
3
6, 7
24
Cannot eject disc. The unit may have a problem. While the unit is off, press and hold [;] and
[< OPEN/CLOSE] on the main unit at the same time for about 5 seconds to force
the tray to eject. Remove the disc and consult the dealer.
Start up is slow.
It takes time before play
starts.
Start up takes time in the following situations.
Immediately after a power failure or the AC power supply cord is connected.
When the unit is connected with an HDMI cable.
[DivX]: This is normal on DivX video.
Cannot set “On” in “24p
Output”.
Only when the unit is connected to the HDMI terminal of a TV supporting 24p you
can select “On”. In some cases where the unit is connected to a TV via an
amplifier/receiver through the HDMI terminals, you may not be able to select
“On”. In this case, connect the unit to a TV through the HDMI terminal and
connect it to the amplifier/receiver through any terminal other than HDMI.
32
DMP-BD55_35PP-RQT9243_ENG.book 38 ページ 2008年8月29日 金曜日 午前10時28
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic DMP-BD35 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic DMP-BD35 in the language / languages: English as an attachment in your email.

The manual is 9,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic DMP-BD35

Panasonic DMP-BD35 User Manual - English - 44 pages

Panasonic DMP-BD35 User Manual - English, German - 2 pages

Panasonic DMP-BD35 User Manual - German - 80 pages

Panasonic DMP-BD35 User Manual - Dutch - 2 pages

Panasonic DMP-BD35 User Manual - Dutch - 132 pages

Panasonic DMP-BD35 User Manual - Danish - 2 pages

Panasonic DMP-BD35 User Manual - Danish - 132 pages

Panasonic DMP-BD35 User Manual - French - 40 pages

Panasonic DMP-BD35 User Manual - French, Italian - 2 pages

Panasonic DMP-BD35 User Manual - Italian - 80 pages

Panasonic DMP-BD35 User Manual - Swedish - 2 pages

Panasonic DMP-BD35 User Manual - Swedish - 132 pages

Panasonic DMP-BD35 User Manual - Spanish - 2 pages

Panasonic DMP-BD35 User Manual - Spanish - 132 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info