597960
99
Zoom out
Zoom in
Previous page
1/116
Next page
99
8
8-4 VF
8-4-1 VF DISPLAY 8-4-2 VF MARKER
8-4-3 USER BOX
The ____ in the Adjustable Range column indicates the preset
mode.
Items/
Data Saved
Adjustable
Range
Remarks
DISP
CONDITION
NORMAL
HOLD
NORMAL
: Display status constantly.
HOLD: Display status only when the
MODE CHECK switch is pressed.
–CUFE
DISP MODE 1
2
3
Set the DISP MODE.
Switch the camera’s Warning/Message
indication. Please refer to [4-7-4 Display
Modes and Setting Changes/adjustment
Result Messages] for more information.
–CUFE
VF OUT Y
NAM
R
G
B
Select the VF output.
Y: Brightness signal
NAM: Output signal with the highest level
among R, G, and B signals.
R: Rch signal
G: Gch signal
B: Bch signal
–CUFE
VF DTL 0
:
3
:
5
Select the VF DTL.
Additionally enhance the DTL for the VF
signal. 0 setting is the same DTL as the
primary scan lines.
–CUFE
ZEBRA1
DETECT
0%
:
70%
:
109%
Set the ZEBRA1 detection level (IRE value).
–CUFE
ZEBRA2
DETECT
0%
:
85%
:
109%
Set the ZEBRA2 detection level (IRE value).
–CUFE
ZEBRA2 ON
SPOT
OFF
Set the ZEBRA2 to ON, OFF, or SPOT.
–CUFE
LOW LIGHT LVL OFF
10%
15%
20%
25%
30%
35%
Set the camera incoming light volume at
which to display LOW LIGNT.
–CUFE
ECU MENU
DISP.
ON
OFF
Set the menu display on the VF to ON or
OFF when the ECU is connected.
–CUFE
50M
INDICATOR
ON
OFF
Set the 50M recording indication to ON or
OFF.
–CUFE
MARKER/CHAR
LVL
50%
60%
70%
80%
90%
100%
Adjust the brightness of markers and
characters displayed on the VF.
–CUFE
Items/
Data Saved
Adjustable
Range
Remarks
TA BL E A
B
Select the VF MARKER setting table.
First, select table A or B, then set the items
below for each table.
–CUFE
CENTER MARK OFF
1
2
3
4
Switch the center mark.
OFF: Do not display center mark.
1: + (large)
2: Hollow (large)
3: + (small)
4: Hollow (small)
–CUFE
SAFETY ZONE OFF
1
2
Select the frame type for the safety zone.
OFF: Do not display frame.
1: Box
2: Corner frame
–CUFE
SAFETY AREA 80%
:
90%
:
100%
Set the position of the safety zone.
–CUFE
FRAME SIG 4:3
13:9
14:9
VISTA
Set the frame marker.
Only enabled when REC MODE is set to
16:9.
The VISTA ratio is 16:8.65.
–CUFE
FRAME MARK ON
OFF
Set the frame marker to ON or OFF.
–CUFE
FRAME LVL 0
:
15
Set the level outside the frame marker.
0: Equivalent to signal OFF.
15: Same brightness as center area.
This setting, however, is disabled if
the FRAME SIG is set to VISTA.
–CUFE
Items/
Data Saved
Adjustable
Range
Remarks
USER BOX ON
OFF
Select whether or not to display the USER
BOX.
–CUFE
USER BOX
WIDTH
1
:
13
:
100
Set the width of the USER BOX.
–CUFE
USER BOX
HEIGHT
1
:
13
:
121
Set the height of the USER BOX.
–CUFE
USER BOX H
POS
–50
:
+00
:
+50
Set the horizontal position of the USER
BOX.
–CUFE
USER BOX V
POS
–121
:
+000
:
+121
Set the vertical position of the USER BOX.
–CUFE
99


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-SPX 800P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-SPX 800P in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info