597960
86
Zoom out
Zoom in
Previous page
1/116
Next page
86
6. Inspection of the clock, time code, and user bits
1 Set the user’s bit as required.
Please refer to [4-5-1 Setting the User Bits] for the setting
procedures.
2 Set the time code.
Please refer to [4-5-3 Setting the Time Code] for the setting
procedures.
3 Set the TCG switch to [R-RUN].
4 Press the REC START/STOP button.
Check that the counter display number changes as
recording progresses.
5 Press the REC START/STOP button again.
Check that recording stops and the counter display number
stops changing.
6 Set the TCG switch to [F-RUN].
Check that the counter display number changes regardless
of recording status.
7 Set the DISPLAY switch to [UB].
Each time the HOLD button is pressed, make sure that the
displayed value changes in the following sequence: VTCG
DATE TIME No display (time zone) TCG; and
also verify that the displayed value is correct.
If DATE, TIME, or time zone is not correct, refer to [4-5-2
Setting the Internal Clock’s Date and Time] for guidance on
setting the correct values.
<Note>
Note that date and time data set for DATE, TIME, and time
zone is recorded in clips, and affects the playback
sequence, etc. at the time of thumbnail manipulations.
7-2 Maintenance
7-2-1 Cleaning Inside the Viewfinder
z Do not use thinner or other solvents to remove dirt from the
viewfinder.
z Wipe the lens with a commercially available lens cleaner.
z DO NOT wipe the mirror. If dirt or rubbish is sticking on the
mirror, remove it with a commercially available air blower.
7-2-2 Phenomenon Inherent to CCD
Cameras
Smears
Smears may appear when shooting an object with very high
brightness.
This phenomenon may appear more frequently as the electronic
shutter speed increases.
7-2-3 Replacing the Backup Battery
The camera is shipped from the factory with a backup battery
already mounted.
When the battery runs out, the [BACK UP BATT EMPTY] display
appears on the viewfinder screen for 3 seconds after the power
switch is turned ON.
The internal clock stops operating when the battery runs out.
Also, the TCG time code value returns to [00:00:00:00], and the
time code backup is disabled. The battery must be replaced.
Please consult your nearest service center for replacement with
a new battery (CR2032).
The backup battery is visible when the panel on the LCD monitor
side is removed (right side when viewed from the front).
<Note>
Please contact the store where you purchased the camera or
an authorised service provider when replacing the battery.
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-SPX 800P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-SPX 800P in the language / languages: English as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info