597959
16
Zoom out
Zoom in
Previous page
1/124
Next page
16
Chapter 2 Parts and their Functions (continued)
VIDEO OUT OUTPUT SEL switch
Used to switch the signals output from the VIDEO OUT
connector.
MEM: In EE (recording) mode, video from the camera is
output. In VV (playback) mode, playback signal
from a P2 card is output.
CAM: Video from the camera is output constantly.
OFF: Video is not output. The camera-recorder
operates in power-saving mode.
Note that the audio output is synchronised with the
video.
For types of video outputs, see [4-9-2 Selecting Video
Output Signals].
<Notes>
z During recording, this switch does not switch output
signals before stopping the recording operation.
z Even if this switch is set to “CAM”, if “VIDEO” or
“1394” is selected for REC SIGNAL the AJ-SPC700P
performs the operation when “MEM” is selected. The
menu option REC SIGNAL is found in the SYSTEM
MODE screen on the SYSTEM SETTING page.
REW (rewind) button and lamp
During pause, this button performs a fast-reverse
playback with the lamp blinking.
During playback, it performs an approximately 4C fast-
reverse playback with the PLAY and REW lamps
blinking.
If this button is pressed when playback is paused, the
start of the clip being played back is located in pause
mode.
FF (fast forward) button and lamp
During pause, this button is used to perform fast
playback with the lamp blinking.
During playback, it performs an approximately 4C fast
playback with the PLAY and FF lamps blinking.
If this button is pressed when playback is paused, the
start of the next clip is located in pause mode.
STOP button
This button stops playback.
PLAY/PAUSE button
This button is used to view playback using the
viewfinder screen or a color video monitor. The lamp
comes on when playback starts.
In playback mode, this button pauses (PLAY PAUSE)
playback with the lamp blinking.
REC button
Pressing this button starts recording, and pressing
again stops recording.
This button has the same function as the REC
START/STOP button and the VTR button at the lens.
It may be disabled with the recording protection
button.
REC protection button
This button disables the REC button on the handle.
ON: The REC button is enabled.
OFF: The REC button is disabled.
P2 CARD ACCESS LED
This LED indicates the recording and playback status of
each card.
Slide lock button
Used to open the slide-out door for inserting P2 cards.
While depressing this button, slide the door to the left.
USB 2.0 connector
A USB 2.0 cable is connected here.
When the menu option USB is set to “ON”, data can be
transferred via USB 2.0. During such data transfer,
recording, playback or operations of clips is not
permitted.
The menu option USB is found in the SYSTEM MODE
screen on the SYSTEM SETTING page. For more
information, see [5-5 Connection between the USB 2.0
port of the AJ-SPC700P and a PC].
GENLOCK IN connector
This connector is used to input a reference signal when
the camera unit is gen-locked, or when the time code is
externally locked. If VIDEO is selected for the menu
option REC SIGNAL, the connector can be used to
record actual signals. The menu option REC SIGNAL is
found on the SYSTEM MODE screen on the SYSTEM
SETTING page.
<Notes>
z The reference input signal must be a standard VBS
(Video Burst Sync).
z If you need to synchronise the input signal with the
AJ-SPC700P when “VIDEO” is selected for the REC
SIGNAL, set the menu option GENLOCK to “EXT”.
The option GENLOCK is found on the GENLOCK
screen, which is accessible from the SYSTEM
SETTING page.
CAM OUT (camera output) connector
This connector outputs video signals from the camera. It
does not output playback signals.
Connector cover
Remove the cover, and install the DVCPRO/DV
connector. For directions on attaching the connector,
see the instruction manual for the IEEE1394 interface
board. (AJ-YAD800G, optional accessory)
ECU REMOTE (remote control) connector
The extension control unit AJ-EC3P (optional
accessory) is connected here.
#,52%2'PINKUJDQQMࡍ࡯ࠫ㧞㧜㧜㧢ᐕ㧡᦬㧝㧝ᣣޓᧁᦐᣣޓඦ೨㧥ᤨ㧠㧡ಽ
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-SPC 700P at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-SPC 700P in the language / languages: English as an attachment in your email.

The manual is 6,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info