99987
80
Zoom out
Zoom in
Previous page
1/134
Next page
80
Chapter 5 Preparation
5-1 Supplying the power
A battery pack or an external DC power supply can be used
as this unit’s power supply.
To use the battery pack, there is the following
choice of makes of batteries:
Anton/Bauer
IDX
PACO
Sony
Types of battery can be confirmed and revised in the
viewfinder or the menu screen on the monitor.
Press the MODE CHECK button on the side panel of the
unit to display the type of the battery currently set at the top
right of the viewfinder screen.
Using the menu operation, open the <BATTERY/TYPE>
screen from the VTR MENU page to confirm/change it in
the BATTERY SELECT item.
<Notes>
Batteries of other makes can also be supported by
changing the setting menu but no guarantees are made for
the system when they are actually used with this unit.
Before using the battery pack, recharge the battery using
the battery charger.
(For details on the recharging method, refer to the
operating instructions of the battery concerned.)
5-1-1 Attaching the battery and setting the
battery type
Using the Anton/Bauer battery pack
1
Attach the battery pack made by Anton/Bauer.
2
Insert the battery pack and slide it in the direction of the
arrow.
Battery pack made
by Anton/Bauer
<Reference>
A battery holder made by Anton/Bauer is equipped with a
power output connector for the lighting and a lighting control
switch to enable a light to be easily attached. For details on
the lighting systems available, contact Anton/Bauer.
3
Set the battery type.
Select the battery type using the BATTERY SELECT
menu item. This item is selected from the
<BATTERY/TAPE> screen on the VTR FUNCTION
page.
For details, refer to “7-8-3 BATTERY SETTING1.”
Anton/Bauer batteries which can be used
O PROPAC14
O TRIMPAC14
O HYTRON50
O HYTRON100
O HYTRON120
O DIONIC90
O DIONIC100
O DIONIC160
<Reference>
To remove the battery pack, slide it in the opposite direction
to the one in which it was attached while keeping the release
lever on the battery holder pulled down all the way.
Release lever
#
< BATTERY/TAPE >
BATTERY SELECT :DIONIC
EXT DC IN SELECT :AC-ADPT
BATT NEAR END ALARM :OFF
BATT NEAR END CANCEL:ON
BATT END ALARM :ON
BATT REMAIN FULL :70%
TAPE NEAR END ALARM :ON
TAPE NEAR END TIME :2min
TAPE END ALARM :ON
TAPE REMAIN/ :3min/
Power output connector for lighting
Lighting control
switch
01.AJ-HDX900_P_E(VQT0X86)_E 06.6.27 10:09 AM ページ80
80


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-HDX900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-HDX900 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info