99987
46
Zoom out
Zoom in
Previous page
1/134
Next page
46
1
Set the POWER switch to ON.
2
Set the TCG switch to F-RUN.
4
Supply the reference time code and reference video
signal, which are in a phase relationship that satisfies
the time code standard, to the TC IN connector and
GENLOCK IN connector respectively.
3
Set the DISPLAY switch to TC.
Operating procedure for external locking
Follow the steps below for external locking.
The built-in time code generator is now locked to the
reference time code.
About 10 seconds after locking, the external lock status will
be retained even if the connection of the externally supplied
reference time code is disconnected. However, the servo
lock will be subject to disturbances if it is connected or
disconnected during recording.
O When the power of the unit is turned off, the time code is
unlocked.
O The accuracy of the time code is ± 20 seconds a month.
<Note>
When the external lock operation is performed, the time code
is instantly locked to the external time code, and the same
value as the external code value appears on the counter
display. Do not set the unit to the recording mode during the
few seconds it takes for the sync generator to stabilize.
Concerning the user bits setting during external
lock
When the unit’s time code is externally locked, only the time
data is locked to the time data of the time code supplied from
the external source. This means that the user bits can be set
separately for each component.
When the <TC/UB> screen is opened from the VTR menu
page and EXT is selected as the UB MODE item setting by
performing menu operations, the user bits can also be locked
to the user bits of the time code supplied from the external
source.
To release the external lock
First stop supplying the external time code, and set the TCG
switch to R-RUN.
Chapter 4 Adjustments and settings for recording
(continued)
TCG
TC OUT
TC OUT
TC IN
TC IN
AJ-HDX900
TC OUT
AJ-HDX900
GENLOCK IN
GENLOCK IN
GENLOCK IN
TC IN
TC OUT
AJ-HDX900
TC IN
DAT
1st unit
Settings of the TC
VIDEO SYNCRO item: 1
From the 2nd unit to the
(n–1)-th unit
n-th unit
Settings of the TC
VIDEO SYNCRO item: 0
Settings of the TC
VIDEO SYNCRO item: 2
Example 6:
When an external device is locked to the time code
generator of this unit, which is connected in a cascade
configuration.
To be connected if necessary
A device that synchronizes with the TC IN
input and capable to record without delay
(such as DAT or a camera recorder)
Reference video signal
01.AJ-HDX900_P_E(VQT0X86)_E 06.6.27 6:01 PM ページ46
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-HDX900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-HDX900 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info