99987
18
Zoom out
Zoom in
Previous page
1/134
Next page
18
9
8
7
4
6
5
2-5 Time code related section
1 GENLOCK IN connector (BNC)
The HD Y reference signal is supplied to this connector
when the camera unit is to be gen-locked or the time code
is to be externally locked. It is also possible to supply
composite video signals instead as the reference signal.
2 TC IN connector (BNC)
Supply the time code which will serve as the reference to
this connector when externally locking the time code.
<Note>
A time code with the same format as the system mode of
the unit must be input.
3 TC OUT connector (BNC)
To lock the time code of an external VTR to the units time
code, connect this connector to the time code input (TC
IN) connector on the external VTR.
4 HOLD button
The time data display of the counter display section which
was on the screen at the moment when this button is
pressed is held. (However, the time code generator
keeps running.) When the button is pressed again, the
hold status is released.
It is used, for instance, to find out the time code or CTL
counter value at which a particular scene was shot.
5 RESET button
This is used to reset the time data on the counter display
section to 00:00:00:00. If it is pressed while the TCG
switch 9 is at the SET position, the time code data and
user bits data are respectively reset to 00:00:00:00.
6 DISPLAY switch
This is used to display the time code, CTL or user bits on
the counter display section depending on the setting
positions of this switch and the TCG switch 9.
UB : The user bits are displayed.
TC : The time code is displayed.
CTL : CTL is displayed.
7 “+” button, “–” button
These are used to increment or decrement by 1 the figure
in the digit which was made to flash by the SHIFT button
8 when the time code or user bits are to be set.
8 SHIFT button
This causes the digit to be set to flash when the time code
or user bits are to be set.
9 TCG (time code selector) switch
This is used to set the running mode of the built-in time
code generator.
F-RUN : Set here to have the time code run all the time
regardless of the VTRs operation.
This position is used to align the time code with
the time or externally lock the time code.
SET : Set here when the time code or user bits are to
be set.
R-RUN : Set here to have the time code run only during
recording. The time code on the tape with
scene-to-scene continuity is recorded
continuously.
Chapter 2 Parts and their functions
(continued)
01.AJ-HDX900_P_E(VQT0X86)_E 06.6.22 12:52 PM ページ18
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-HDX900 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-HDX900 in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info