99989

Panasonic AJ-HDC27HP Manual

134
Zoom out
Zoom in
Previous page
1/140
Next page
134
Inspections prior to shooting (continued)
Inspecting the aperture and
zoom functions
Inspecting the VTR unit
1
Set the zoom to the motorized zoom mode, and
check its operations in this mode.
Check that the image changes when the zoom is
set to the telephoto and wide-angle positions.
1. Tape travel inspection
1
Set the VTR SAVE/STBY switch to SAVE, and
check that the VTR SAVE lamp inside the
viewfinder lights.
2
Set the VTR SAVE/STBY switch to STBY, and
check that the VTR SAVE lamp goes off.
3
Set the TCG switch to R-RUN.
4
Set the DISPLAY switch to CTL.
5
Press the unit’s VTR START button, and check
that:
O The tape reels rotate.
O The figure shown on the counter display
changes.
O The REC lamp inside the viewfinder lights.
O The RF and SERVO displays do not appear in
the display window.
6
Press the unit’s VTR START button again. Check
that the tape stops and the REC lamp inside the
viewfinder goes off.
7
Use the lens VTR button to check the same
operations as in steps 5 and 6.
8
Press the RESET button, and check that
“00:00:00:00” appears on the counter display.
9
Set the LIGHT switch to ON, and check that the
display window illuminates.
10
Press the REW button, and after the tape has
been rewound for a few seconds, press the
PLAY/PAUSE button.
Check that the tape is recorded, played back
and rewound properly.
11
Press the FF button, and check that the tape is
fast forwarded properly.
2
Set the zoom to the manual zoom mode, and
check its operations in this mode.
Turn the manual zoom lever, and check that the
image changes when the zoom is set to the
telephoto and wide-angle positions.
3
Set the aperture to the auto adjustment mode,
point the lens at some objects with different
brightness levels, and check that the auto aperture
adjustment works.
4
Set the aperture to the manual adjustment mode,
turn the aperture ring, and check that the manual
aperture is adjusted.
5
While holding down the auto instantaneous
aperture adjustment button, point the lens at some
objects with different brightness levels, and check
that the auto instantaneous aperture adjustment
function works.
6
Return the aperture to the auto adjustment mode,
switch the GAIN switch setting to L, M and H, and
check that:
O The aperture is adjusted for objects of the same
brightness level in tandem with the switching of
the gain setting.
O The gain displayed on the viewfinder screen is
switched in tandem with the switching of the
gain setting.
7
When a lens with an extender has been installed,
set the extender to the operating position, and
check that it works properly.
Perform all the steps outlined in section “1. Tape
travel inspection” through section “4. Earphone and
speaker inspection” one after the other.
04. 英(P128-表４/140) 05.5.18 10:45 ページ134
… 134 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-HDC27HP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-HDC27HP in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info