99989
45
Zoom out
Zoom in
Previous page
1/140
Next page
45
Viewfinder screen status displays (continued)
1 Extender display
This appears when the lens extender is being used.
2 Shutter speed/mode display
This indicates the shutter speed or shutter mode
setting.
The unit in which the shutter speed is displayed can
be set on the VF DISPLAY screen of FILM (CAM)
MAIN MENU 2.
O OFF (no display):
The shutter is not used.
O 1/100, 1/120, 1/250 1/500, 1/1000, 1/2000
(180d, 172.8d, 144d, 120d, 90d, 45d):
Shutter speeds in the fixed mode
O 3.0d to 350.0d/0.8% to 97.2% (SYNCHRO
SCAN):
Selection of synchro scan mode
In the synchro scan 1 mode, “Y” appears
immediately in front of the number displayed.
3 Remaining tape display
During recording, this shows the remaining tape (in
minutes) in the VTR. When less than two minutes
of tape remain, the figure starts flashing.
4 Battery voltage display
This indicates the battery voltage (V) during
operation. The voltage is displayed as a
percentage when a digital battery is used.
5 Filter display
This indicates the type of filter selected.
6 White balance memory display
This indicates the automatic adjustment memory
selected for the white balance.
A: The WHITE BAL switch has been set to “A.”
B: The WHITE BAL switch has been set to “B.”
P: The WHITE BAL switch has been set to “PRST.”
7 Gain display
This indicates the gain (dB) of the video amplifier
which was set using the GAIN switch.
8 Audio level display
This indicates the audio level (which can be
displayed separately for audio CH1 and CH2).
During sine wave input, it roughly corresponds with
the VTR’s level meter as shown below.
9 Aperture display
This indicates the approximate aperture setting (F
number).
<Note>
This appears when a lens with an aperture display
function is being used.
: Camera warning/information display
The black balance, white balance, auto knee
function, super iris, super gain and other alarm
displays and warnings appear here.
; Safety zone markers
These indicate the 80% or 90% (factory setting)
range of the surface area of the viewfinder screen.
The display range proportion is set on the VF
DISPLAY screen of the setting menu.
For details, refer to “Setting the marker displays”
(page 49).
< Center marker
This indicates the center of the viewfinder screen.
The display is set ON or OFF on the VF DISPLAY
screen of the setting menu.
= Super iris ON display
“S” appears when the super iris is ON.
> Zoom position display
The distance from the WIDE end to TEL end of the
zoom lens is indicated here as a number from 0 to
99.
? TCG display
This indicates the time code generator value.
@ Master gain setting display
The GAIN L/M/H values currently set appear here
when the MODE CHECK button is pressed.
A Color temperature display PRE/A/B
This indicates the color temperature when AWB is
executed using white balance memory A or B.
Audio level display
VTR’s level meter
-40 -30 -25 -18/20 -15 -10 -5 0
+
02. 英(P26-88) 05.5.18 10:42 ページ45
45


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic AJ-HDC27HP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic AJ-HDC27HP in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info