683926
2
Zoom out
Zoom in
Previous page
1/2
Next page
BA 873031led N;DE,GB -23816- 2017.10V02
INSTRUCTION MANUAL DIMMER [LED] WITHOUT NEUTRAL WIRE
Technical Features
Safety instructions
Supply voltage
230 V, 50Hz
CAUTION!! DANGER OF LIFE / RISK OF FIRE AND ELECTRIC SHOCK!!
Power consumption
0,7 W
Suitable type of lamps
Dimmable LED lamps
LOAD
LED 1: Dimmable 230V~ LED lamps* (leading edge dimming)
4 - 80 W
Installation and assembly of electrical equipment must be carried out only by professional electrician!
Connect the supply voltage/frequency as stated on the product!
Disconnect device from power supply for wiring and installation purposes!
Check power supply is disconnected!
Defective devices have to be put out of service immediately!
Warranty void if housing opened by unauthorised person!
The electronic circuit is protected against a wide range of external influences. Incorrect operating may occur if
external influences exceed certain limits!
Installation and assembly of electrical equipment must be in accordance with local building and electrical codes!
If the LED lamp don’t turn off completely after the switch-off command, the compensator (included in delivery) must
be installed parallel to the lamp!
LED 2: Dimmable 230V~ LED lamps* (trailing edge dimming).
4 - 200 W
LED 2: Dimmable 12V~ LED lamps* (trailing edge dimming)
with Electronic transformer, type C
1 lamp per transformer /
max. 4 transformers (50W)
Max. number of pushbuttons
unlimited (not compatible with lighted
pushbuttons)
Dimensions
46 x 42 x 13 mm
Weight
23 g
Permitted ambient temperature
Storage temperature
0º … +40ºC
-30º … +70ºC
Type of protection
IP20 according to DIN EN 60529
Important Note
Conformity with Standard
DIN EN 60669-2-1
For all transformers and lamps, please take into account the specifications of the manufacturer!
NOTICE: In order to install the dimmer correctly, its connections must be installed to connecting devices (or
connection terminals) which fulfill with the Standards EN 60998-1, EN 60998-2-1 or EN 60998-2-2.
*Check the technical specification of the lamps.
Description / Installation / Operation
Wiring diagram
Wiring example
Description
Small size dimmer, for flush-mounting (e.g. behind standard pushbutton)
Protected against overload and short circuit. Built-in heat protection.
Controlled by pushbutton.
With or without memory.
One rotary switch to select the minimum light level and to select the connected lamp load (LED1 or LED2).
- LED 1: Dimmable 230V~ LED lamps* (leading edge dimming)
- LED 2: Dimmable 230V~ LED lamps* (trailing edge dimming).
Dimmable 12V~ LED lamps* (trailing edge dimming) with Electronic transformer, type C
For all transformers and lamps, please take into account the specifications of the manufacturer!
Installation
CAUTION! You must select with the rotary switch (LED1 or LED2) the correct type of connected load in
order to avoid damages of the dimmer or the lamps!
PLEASE NOTE! To avoid undesirable effects when the lamps are dimmed to lowest level (e.g. light
flickering) you have to select with the rotary switch the minimum light level!
1 Disconnect installation from power supply and check that power supply is disconnected.
2 Select with the rotary switch the type of lamp / load you will connect (LED1 or LED2).
3 Install the dimmer according to the wiring diagram.
4 Make sure the loads are connected properly and reconnect power supply.
5 Press shortly the pushbutton to switch the lamps on and dim with a long press to the minimum lighting level.
If the lamps are not switched on correct (e.g. light flickering) please select with the rotary switch the appropriate
and correct minimum light level.
Operation
Press shortly the pushbutton to switch the lamps on and off!
=> Switch on „No Mem= Lamp(s) switches on with max. brightness.
=> Switch on „Mem“ = Lamp(s) switches on with the brightness of the last switch off
With a long press you can dim!
**Note: If the LED lamp don’t turn off
completely after the switch-off command,
the compensator (included in delivery)
must be installed parallel to the lamp!
Quick and easy! One rotary switch to set
the lamp load and the minimum light level
Setting the lamp load Check
the technical specification of the
lamps.
Setting the minimum light
level
/ dimming value
**
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 873 031 led at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 873 031 led in the language / languages: English, German as an attachment in your email.

The manual is 0,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info