683964

Paladin 676 311 rf Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
GB
DE
BATTERY REPLACEMENT
Release the cover of the sensor with the help of a screwdriver. Insert it into the upper slot.
Remove the cover of the socle and remove the battery being careful with the components of
the printed circuit.
The thermostat also indicates low battery status by flashing its red LED when the selection
wheel is moved. At his moment it is necessary to change the battery.
The 676311rf has a channel type CH_Battery_Status (Channel Code 0021h).
This channel allows to inform to a compatible actuator about this information.
When the battery is worned-down, the sensor will send every 15 minutes the respective
telegram and a “battery empty” message.
This function is optional. In order to link the sensor with a compatible actuator:
1.- Remove the battery from the 676311rf.
2.- Set the RF actuator in link mode, according to the instructions given by the
manufacturer.
3.- Insert the battery again in the socle.
4.- Check the correct link between the two devices in the actuator, according to the
instructions given by the manufacturer.
After replacing the battery it is necessary to:
1. - Turn selection wheel to the maximum 30°C position.
2. - Turn selection wheel to OFF position.
FIRST STARTING
NOTE: pull the plastic foil of the battery out to become operative the device.
After removing the plastic foil it is necessary to:
1. - Turn selection wheel to the maximum 30°C position.
2. - Turn selection wheel to OFF position.
BATTERIETAUSCH
Um die Batterie zu tauschen, öffnen Sie die Abdeckung des Sensors mittels eines kleinen
Schraubendrehers. Entfernen Sie anschließend die rückseitige Abdeckung und ersetzen Sie
die Batterie. Hierbei sollten Sie darauf achten, die Leiterplatte nicht zu beschädigen.
Der Sensor meldet eine schwache Batterie anhand einer rot blinkenden LED während der
Verstellung des Drehwahlschalters.
Der Sensor überträgt den Batteriestatus auch per Funk (CH_BATTERY_STATUS:
Channel_Code_0021h), sofern der Empfänger diesen Status auswerten kann. Im Falle
eines niedrigen Batteriestandes wird diese Meldung alle 15 Minuten übertragen.
Um den Sensor mit einem kompatiblen Aktor zu verlinken, der diese Funktion unterstützt
gehen Sie wie folgt vor:
1.- Entfernen Sie die Batterie aus dem Sensor 676 311 rf.
2.- Empfängerkanal des gewünschten RF-(KNX)-Gerätes in den Verlinkungsmodus stellen
(gemäß den Vorgaben des Herstellers)
3.- Batterie einsetzen
4.- Erfolgreiche Verlinkung anhand des Aktors (gemäß den Vorgaben des Herstellers)
prüfen.
Nach einem Batterietausch sind folgende Schritte notwendig:
1.– Drehwahlschalter auf Position 30°C (Maximalwert) stellen.
2.– Anschließend: Drehwahlschalter auf Position “AUS” stellen.
ERSTINBETRIEBNAHME
Wichtig: Ziehen Sie die Schutzfolie der Batterie heraus um das Gerät verwenden zu
können.
Nach dem Entfernen der Schutzfolie sind folgende Schritte notwendig:
1. – Drehwahlschalter auf Position 30°C (Maximalwert) stellen.
2. – Anschließend: Drehwahlschalter auf Position “AUS” stellen.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paladin 676 311 rf at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paladin 676 311 rf in the language / languages: English, German as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info