779805
25
Zoom out
Zoom in
Previous page
1/32
Next page
the problem, contact your dealer or the
manufacturer directly. Use only original
parts approved by the manufacturer,
otherwise a hazard risk arises.
ENGINE WILL NOT START
Possible causes;
1. Fuel tank is empty.
2. Fuel tap is in the OFF position.
3. Choke is at the RUN position.
4. Engine switch is in the OFF position.
5. Spark plug dirty/defective.
6. Spark plug wet with fuel (flooded engine).
7. Poor quality fuel; Pressure washer stored
without treating or draining petrol, or refueled
with bad petrol.
8. Low engine oil level.
9. Fuel filter clogged, carburetor malfunction,
ignition malfunction, valves struck, etc.
Possible corrective actions;
1. Refill with clean unleaded petrol.
2. Move fuel tap to ON position.
3. Move choke lever to START position.
4. Turn engine switch to ON position.
5. Check that spark plug wire is connected
properly. Clean or replace spark plug with
properly gapped spark plug.
6. Dry and reinstall spark plug. Start engine with
throttle lever in FAST position.
7. Drain fuel and carburetor and refuel with
fresh petrol. Please contact after sales service
for further assistance.
8. Add engine oil to proper level, see engine
manual.
9. Take engine to your dealer and/or contact
after sales service for instructions.
ENGINE LACKS POWER
Possible causes;
1. Air filter clogged
2. Throttle control is in the slow position
3. Fuel filter clogged, carburetor malfunction,
ignition malfunction, valves struck, etc.
4. Poor quality fuel; Pressure washer stored
without treating or draining petrol, or refueled
with poor quality fuel.
Possible corrective actions;
1. Clean or replace filter.
2. Move throttle control to fast position.
3. Take engine to an authorized servicing
dealer and/or contact after sales service.
4. Drain fuel and carburetor and refuel with
fresh gasoline. Please contact after sales
service for further assistance.
LOW OR SURGING PRESSURE
Possible causes;
1. Insufficient water supply.
2. Blocked inlet screen.
3. Need to use high pressure nozzle.
4. Blocked.
5. Worn nozzle.
6. Leaking high pressure hose.
Possible corrective actions;
1. Increase water flow check for kinked or
pinched hose.
2. Carefully remove screen and clean.
3. Change to correct nozzles either green,
yellow, white, or red nozzle.
4. Safely remove nozzle as outlined in this
manual and check for blockage.
5. Replace nozzle.
6. Fix leaks if not leaking from hose NB DO
attempt to repair hose leaks.
NO DETERGENT
Possible causes;
1. Need to use different nozzle.
2. Back pressure from extra-long hose.
3. Leak in clear detergent hose.
4. Detergent strainer not submerged.
5. Detergent strainer blocked.
Possible corrective actions;
1. Change to the BLACK nozzle.
2. Try shorter high pressure hose.
3. Replace hose. Use hose clamps if necessary.
4. Make sure strainer is completely submerged
in solution.
5. Clean detergent strainer.
7. TROUBLESHOOTING
7.1. If troubleshooting does not solve
Page 25
First edition - April 2017
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for P1PE P72800A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of P1PE P72800A in the language / languages: English as an attachment in your email.

The manual is 9.45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info