ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT SE
1. Motor cover
2. Lifting handle
3. Lower handle
4. Cord retainer
5. Safety switch
6. Upper handle
7. Height adjustment lever
8. Handle securing knob
9. Grass catcher ap
10. Grass catcher
1 Quick release handle
12. Start/stop lever
2. ASSEMBL 5. HOW T
ECOMOW ELECTRIC MOWER
The height adjustment lever provides 5 cutting heights from 25mm to
65mm.
1.
button.
1
910 11 12
13
2 3 4 6
7 8
14
•
of this tool.
• Heavy duty power leads recommended not exceding 25m.
•
and long trousers.
•
they could be thrown by the blade.
•
signs of wear or damage and repair as necessary
•
preserve balance.
5
W ENSURE THE T
FROM THE POWER SUPPL.
Fitting the Lower Handle to Mower Body
1.
cable clip attached must be
assembled on the power cable
side.
1.
the upper ends of the lower
handle. From the handle
securing set, t the bolts
through the inner side of the
lower handle and then through
the hole in the upper handle.
Note: When you t the upper
handle you can decide the height
of the upper handle by selecting
the appropriate fastening hole.
2.
in place by screwing the
supplied handle securing
lever over the protruding ends
of the bolts.
Ensure the cord follows the handle
smoothly from the switch to the body
of the mower
T
dual action switch
2.
align the two halves and push
them together
time. Ensure the two halves click
together around the entire middle
section.
1.
handle onto the opening
on the top half of the grass
catcher
into position when aligned
and tted correctly
W WHEN
CA
EMPTYING,
UP OF GRASS IN THE GRASS CHUTE. IF NEEDING T
CLEAR THE GRASS,
IS DISCONNECTED FROM THE POWER SUPPL
PRIOR TO CLEARING.
GRASS CHUTE MA
INTO THE GRASS CA
W DISCONNECT THE MOWER FROM
THE POWER SUPPL
HAS STOPPED COASTING BEFORE
HEIGHT
Securing the Power Cord to the Handles
Assembling the Grass Catcher
Fitting and Removing Grass Catcher
3. ADJUSTMENTS
Cutting
4. SWICHING ON/OFF
W THE BLADE WILL
SECONDS
RELEASED. BE
T
TO ST
nearest to the power point so the
lead is laid out on the lawn you have
already cut.
swing the lawn mower from side to side.
Mowing long thick grass may cause the motor speed to drop; you will
hear a change in the motor sound. If the motor speed drops you may
overload your lawn mower
in long thick grass rst cut with the cutting height set in the highest
position, this will help reduce the load.
Do Not Overload the Mower
Fitting the Upper Handle to the Lower Handle
3.
then lift the grass catcher with the other hand up off the two
raised housing clips.
1.
hand and guide the catcher over
the two hooks on the mower
housing.
2.
and lower the catcher ap. The
catcher ap is held against the
gass catcher by a spring.
W KEEP
POWER
FROM BLADES.
Grass Catcher V
T
is full, the mower provides a volume
indicator
Indicator oats up when empty
Indicator is down when full.
Overload Protection
The mower has an internal cut off switch which will stop the operation
of the motor temporarily if too high in temperature. This cut of
will suddenly stop the motor from operating should the motor become
too hot during the operation of the mower
First disconnect the mower from the power supply and inspect blade
for any obstructions.
A
temperature and the operation being performed, before switching On
the mower and resuming normal operation.
CAUTION: TO REDUCE THE RISK OF ELECTRICAL
WE RECOMMEND THE USE OF
DEVICE (RA
3.
stop the mower
1.
towards the mower body
2.
cutting height.
3.
securely seated in the required
cutting height.
Fitting the Rear Wheels
1.
shown.
2.
washer and p-clip.
3.
centre of the wheel so it clicks
into place.
2.
the lower handle washer and
securing knob.
4.
remaining wheel. CAUTION: BE CAREFUL DURING CUTTING HEIGHT
ADJUSTMENTS OF THE LA
ENTRAPMENT OF THE FINGERS BETWEEN MOVING
HEIGHT
HOUSING.
2.
towards the handle to start
the motor and then release
the lock-off button.
3.
top onto the bottom half of the
grass catcher assembled in
step 2.
and push each individual
plastic lug into its opposite
location.
1.
switch housing to the lower handle
as shown.
When mowing long grass
be sure to not overload the
motor
highest cutting height and
then to the desired height.
This will help reduce the
load.
15
13. Rear wheel set
14. Lower handle securing set
15. Upper handle securing set
ELM-1536
ELM-1536U
1. BEFORE USE
Items Supplied
Please check that the article is complete as specied in the scope of delivery
If parts are missing, please contact our service centre or the sales outlet where
you made your purchase at the latest within 5 working days after purchasing
the product and upon presentation of a valid bill of purchase.
to the warranty table in the service information at the end of the operating
instructions.
• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation
braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.
Danger!
The equipment and packaging material are not toys. Do not let children
play with plastic bags, foils or small parts. There is a danger of
swallowing or suffocating!
Proper Use
The lawn mower is intended for private use i.e. for use in home and gardening
environments.
Private use of the lawn mower refers an annual operating time generally not
exceeding that of 50 hours, during which time the machine is primarily used
to maintain small-scale, residential lawns and home/hobby gardens. Public
facilities, sporting halls, and agricultural/forestry applications are excluded.
Important. Due to the high risk of bodily injury to the user
may not be used to trim bushes, hedges or shrubs, to cut scaling vegetation,
planted roofs, or balcony-grown grass, to clean (suck up) dirt and debris off
walkways, or to chop up tree or hedge clippings. Moreover
may not be used as a power cultivator to level out high areas such as molehills.
For safety reasons, the lawn mower may not be used as a drive unit for other
work tools or toolkits of any kind, unless they have been expressly permitted by
the manufacturer
The equipment is to be used only for its prescribed purpose.
deemed to be a case of misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial,
trade or industrial applications. Our warranty will be voided if the machine is
used in commercial, trade or industrial businesses or for equivalent purposes.
Caution!
Residual risks
Even if you use this electric power tool in accordance with instructions,
certain residual risks cannot be rules out. The following hazards may
arise in connection with the equipment’
1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3.
a prolonged period or is not properly guided and maintained.
W
This equipment generates an electromagnetic eld during operation. Under
certain circumstances this eld may actively or passively impede medical
implants. T
with medical implants to consult their doctor and the manufacturer of the
medical implant prior to using the equipment.
OPERA
