606573

Oxford OF698 HotGrips Light Manual

3
Zoom out
Zoom in
Previous page
1/40
Next page
B: Parts list for product: OF698
Before fi tting, check that the following parts are included in the kit:
• 1 x Left HotGrip (22mm I/D x 125mm long )
• 1 x Right HotGrip (25.6mm I/D x 125mm long)
• 1 x Rainproof Panel mounted Switch rated to IP56
• 1 x Wiring loom with battery ring leads, 5amp quick-blow glass fuse, cable ties and grip superglue
• 1 x Oxford Hotgrip instructions
• 1 x Flat drill bit (20mm)
Tools needed:
• A course and fi ne fi le for smoothing the throttle slider tube etc.
• Glass paper for cleaning the handlebars
• Cable snippers or pliers
• Standard motorcycle tools to remove the seat, fairing panels and battery connections
• Power Drill
C: Fitting and Wiring Instructions
Your Oxford HotGrips are designed as a replacement for the handle bar grips already fi tted to the motorcycle.
Hotgrips will fi t onto most motorcycles that use 22mm or 7/8” Ø handlebars. The grip has an open end to al-
low for the bar end weight to be refi tted without the need to trim the grip. If the end of the Hotgrip does need
to be trimmed to ensure that a bar-end weight can be fi tted without fouling the Hotgrips, then it is advisable to
trim up-to the point show in the diagram below. This ensures that the heating elements do not get cut.
If you do not wish to cut the grip, it might be possible to put a metal washer or spacer on the inside of the
bar-end weight to give additional clearance.
The left and right grip are different sizes:
One is designed to fi t over the left handlebar and has an internal diameter of approximately 22mm. The other
fi ts over the throttle slider on the right handlebar and has a diameter of approximately 25mm.
D: Fitting Procedure
1. Remove the existing handlebar grips.
2. Clean the left handlebar ensuring that the bars are smooth and free of glue and residue.
3. The bar should measure a consistent 22mm diameter.
4. If the HotGrips do not slide on easily, check if there is any excess rubber on the inside of the grip
which may have seeped through the expansion slot during manufacturing. If so, use a long fi le
and gently remove the excess rubber with the edge of the fi le.
5. When the right grip is removed there is a nylon throttle slider underneath. This may need to be
removed and any raised areas smoothed off to ensure that the diameter is a consistent 25.6mm.
This often involves fi ling off the raised ridges that were formed on the throttle slider.
Oxford Hotgrips Light instructions v.1 7/9/10 3
Can be trimmed
to this point
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oxford OF698 HotGrips Light at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oxford OF698 HotGrips Light in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info