606569
5
Zoom out
Zoom in
Previous page
1/42
Next page
Oxford Hotgrips instructions v.8 switch - 09/07/12
5
5. Be sure to act immediately to wipe away any excess glue with a dry cloth.
6. Allow the glue to dry for at least 24 hours before using. Ensure that the grips are rmly xed in place before use.
Do not use if the grip moves and seek advice immediately.
H: Wiring Harness Installation
1. Find a suitable location to mount the switch and then take the wiring back to the battery.
2. Install the switch in a suitable position ensuring the wires from the grips reach without strain.
3. The switch may be mounted on a at panel using the self adhesive mounting foam pad. It may also be mounted on
the metal bracket supplied (if the bracket is suitable for the vehicle). Please t the foam pad between the bracket
and switch to reduce vibrations. The bracket may also be bent to a different shape if required.
4. On many bikes it is possible to t the bracket to the clutch clamp as shown below using the longer bolts provided.
5. The loom is designed for ease of tting. There are only 2 wires that need attaching to the motorcycles existing
wiring system. All other connections are through the multi pin block connectors and cannot be fitted the wrong way.
6. We recommend that the wiring loom is positioned away from existing wiring looms on the motorcycle to avoid any
possible electrical interference issues.
7. When the wiring is in position on the motorcycle, we strongly recommend that all connectors are protected with
either electrical insulation tape, waterproof sealing tape or heat shrink tubing (be careful not to damage the cable
when tting heat shrink).
8. Both the negative and the positive battery connections are tted with a ring terminal. This will allow them to be
bolted to the battery terminals. It is both preferable and the easiest option to connect the positive (+ Red wire)
straight to the positive (+) battery terminal so that the switch receives sufcient voltage from the vehicles charging
system.
9. The negative or earth (Black wire) should be connected to the negative (-) battery terminal.
10. If the switch must be connected to a switched ignition supply feed, please ensure that the wiring harness is
connected to main ignition cabling which can take the extra load of up to 4 amps. Problems are commonly found to
be caused when connections are made to horn or any lighting circuits.
Typical problems experienced could be:
- The switch may not come on
- Fuses failing in the fuse box
- Overheating of wires on the bike
- Indicators or lighting malfunctioning
If unsure, please contact your local dealer for advice before fitting these Hotgrips.
Refer to the wiring diagram on the next page.
Install the HotGrip Switch
as shown using the optional
bracket (OF91)
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oxford OF690 HotGrips at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oxford OF690 HotGrips in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oxford OF690 HotGrips

Oxford OF690 HotGrips User Manual - English - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info