587139
7
Zoom out
Zoom in
Previous page
1/51
Next page
EN
5
TROUBLESHOOTING
The below table lists out some of the problems you could encounter. If you are unable to solve the problem, contact the
Customer Care Centre in your country. Contact us via www2.oregonscientific.com/service/support.asp
Problem Possible cause Solution / Remarks
The unit does not
work
Power supply? Ensure plug has been properly inserted into the wall socket
Ensure there is no power failure. Check by connecting
another appliance to the wall socket
The unit does not
work
Normal use This is normal as the light bulb generates heat. However,
ensure there is enough ventilation and vents are not
covered as this can pose a fire hazard.
When setting
functions, the unit
does not respond
Normal use Press RESET at the base of the unit or remove and reinsert
plug into wall socket. The appliance will then be reset to
factory default settings.
The light does not
work
Light intensity is too low? Press to increase light intensity
Alarm function disabled? Ensure alarm time is displayed on LCD screen. Press
ALARM to enable.
Light bulb is defective? Replace the light bulb.
Light bulb not properly
screwed in?
Unscrew and screw in the light bulb again.
Lamp does not turn
on again immediately
after it has been
switched off
Normal operations Allow 3 seconds for the lamp to dim. Please wait until the
lamp reaches the preset intensity level
No sound when the
alarm goes on
Alarm function disabled? Ensure alarm time is displayed on LCD screen. If -:- - is
displayed, press ALARM to enable.
Radio is defective? If radio has been selected for alarm mode, check that radio
works. Press RADIO after you disable the alarm or press
ALARM.
The radio is
defective / produces
a crackling sound
Positioning of external
antenna?
Change position of external antenna if necessary.
Broadcast signal is weak? Press RADIO TUNE to search for the correct signal.
Alarm did not activate
today, but it did
yesterday
Alarm function disabled? Ensure alarm time is displayed on LCD screen. If -:- - is
displayed, press ALARM to enable.
Power failure? Perhaps there was a power failure which lasted longer than
the capacity of the back up system? The display will show
an incorrect time and alarm will be 00:00. Do settings
again.
The light wakes me
too early / late
Location of unit is not
suitable?
It is recommended that the unit is not placed too far and not
lower than your head while in a sleeping position. Make
sure the light is not blocked by bed, duvet or pillow.
Snooze does not
work
Distance? Wave your hand in front of the SNOOZE SENSOR at a
distance range of approx. 1cm to 8cm (0.5 to 3 in).
LCD backlight is too
weak to see
Display brightness? Slide DISPLAY BRIGHTNESS to HIGH.
There is no sound
after plugging to an
external source
External device? Make sure external device is playing.
Connection? Make sure cable is firmly connected with the external
device and the unit.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific WS902 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific WS902 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 20,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info