587085
5
Zoom out
Zoom in
Previous page
1/16
Next page
5
EN
10. Assemble the top pole to the mid-pole.
11. Use the screw to fi x.
12. Ass
emble the wind sensor main body on top of the
pole. Use the screw (Type A) to fi x.
13. Open the battery compartment.
14. Using a compass, rotate the wind direction part until
the
NORTH
indicator points to the “North”.
15. Press
RESET
.
16. Close the battery compartment.
17. Ins
ert the 2 rectangular base legs into the ground to
rmly fi x the pole.
18. To keep the pole stable, use the 3 pins to fi rmly fi x
the tension strings to the ground.
To set up the wind sensor main body on an existing
pole:
1. Remove the screw that fi xes the plastic connector
at the end of the top pole.
2. Slide down the plastic connector.
3. Detach plastic base from the bundled steel pole if
previously installed.
4. Assemble it at the end of the top pole using the
screw that is already attached on the base, with the
washers and bolts to fi x.
14
15
16
12
13
17
18
9
8
10
11
6. Slide the sleeve down to open the battery
compartment.
7. Insert batteries (4 x UM-3 / AA) in the compartment,
matching the polarity (+ / -) and press
RESET
.
8. Slide the protective sleeve up to close the
compartment.
9. Rotate the sleeve to the right to lock.
To s
et up the steel pole support:
1. Assemble the “cone shape” guiding end with the
bottom steel pole.
2. Screw the guiding end clockwise at the bottom of
the pole.
3. Remove the cover hole from the plastic base.
4. Inse
rt the plastic base onto the steel pole until the
screw hole aligns with the support.
5. Use the screw that is already attached on the base,
with the washers and bolts to fi x.
6. Use the guiding end to start inserting the steel pole
at a perpendicular angle into the ground.
WARNING Make sure that there are NO electric
cables / power lines, gas / water pipes in the area
where you are placing the steel pole. Do not place
the pole into a hard rocky type of ground as it may
bend or break the pole. It should be inserted into
soft soil.
7. Place a wooden block on the top of the pole. With
a hammer, hit the wooden block to insert the pole at
a perpendicular angle to the ground until reaching
the base.
8. Asse
mbl
e the mid-pole on top of the bottom pole.
9. Use the screw to fi x.
7
5
8
9
6
1
2
3
4
5
6
7
WMR100_EN_86L4515-017.indd 5 6/15/06 4:25:13 PM
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific WMR100A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific WMR100A in the language / languages: English as an attachment in your email.

The manual is 6,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oregon Scientific WMR100A

Oregon Scientific WMR100A User Manual - German - 15 pages

Oregon Scientific WMR100A User Manual - Dutch - 14 pages

Oregon Scientific WMR100A User Manual - French - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info