796567

Oregon Scientific SH201 Manual

12
Zoom out
Zoom in
Previous page
1/201
Next page
11
EN
NOTE To switch from digital to
analog or analog to digital system,
press the chest belt button for
more than 4 seconds and then
force a signal search.
IMPORTANT If “HR ---“ is displayed because no signal
has been found, press and hold MODE/- to force a signal
search.
In the event that you experience a weak signal or your signal
is disrupted by interference in the environment, follow the
instructions below to identify and resolve the situation.
1. The signal is weak - the watch heart rate monitor will
only show “0”:
• Shorten the distance between the heart rate chest
belt and watch.
• Re-adjust the position of the heart rate chest belt.
• Check the conductive pads are moist enough to
ensure solid contact.
• Check the batteries. If they are low or exhausted,
the transmission range may be shortened.
• Press and hold MODE/- to force a signal search.
2. The gym equipment does not seem to work with your
chest belt and the digital icon is displayed:
• Most gym equipment is compatible with the analog
system . Press and hold the chest belt button
for more than 4 seconds to change from digital to
analog. Then press and hold MODE/- to force a
signal search.
3. Interference from another person’s heart rate monitor
- their heart rate readings appear on your watch, or the
heart rate monitor shows “0”:
• Press the chest belt button to get the watch to
receive your chest belt signal. Do not press and
hold the chest belt button, as it will change the
transmission signal from digital to analog.
4. The signal is jammed - the heart rate reading on your
watch is flashing:
• There is too much interference in the environment
for your heart rate monitor to function. Move to an
area where the heart rate reading stops flashing.
WARNING Signal interference in the environment can be
caused by electromagnetic disturbances. These may occur
near high voltage power lines, traffic lights, overhead lines
of electric railways, electric bus lines or trams, televisions,
car motors, bike computers, some motor driven exercise
equipment, cellular phones or when you walk through
electric security gates. Under interference, the heart rate
reading may become unstable and inaccurate.
NOTE If the watch is kept idle without receiving a heart rate
signal for half a minute, the heart rate mode will quit and
return to clock mode.
START EXERCISING
Before you start exercise, allow the watch a few seconds to
search for chest belt first. This is to ensure you can receive
comprehensive calculations (such as your lap, calorie and
heart rate) during exercise.
Ensure HR zone or limits have been set and if doing pre-
programmed exercise, that the time conditions have been set.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific SH201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific SH201 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 16.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info