You could upload data from the watch onto the application.
1. In CONNECT mode, press top (1) button to enter and toggle middle (2) button to enter upload memory display.
2. Press top (1) button to enter for selecting an exercise profile, toggle middle (2) button to select your desired profile, then press top (1) button to start uploading.
3. Tap CONNECT WITH WATCH on the mobile device to initiate synchronization while pressing top (1) button again on the watch. Done displays on the watch until
successfully connect and upload.
NOTE
If the connection is failed, the watch automatically attempts to synchronize again.
SCREEN MESSAGE
Synchronization in progress
Synchronization successful
Synchronization failed. Watch attempts to synchronize again.
no memoryThere is no data in the watch.
pls change
batt.for
update
The watch battery is low and needs to be replaced
UPDATE SYSTEM
You could update the watch to an advanced system that Oregon Scientific offers in the future through the application, if applicable.
In the application, you can be noticed in INFO page by a message popped up, or browsing NEW VERSION AVAILABLE! at the
below of the page.
1. In CONNECT mode, press top (1) button to enter and toggle middle (2) button to enter update system display.
2. Toggle top (1) button to enter below screens in order. The current watch system will be erased after your confirmation.
NOTE
If the system updating fails, Failed displays, and the screen goes back to start system update for your next trial.
NOTE
In INFO page, you can browse the WATCH ID, VERSION and LAST SYNC TIME.
SOLUTION
Without the phone application “Ssmart”, once you accidentally press the wrong button while updating
SYNC
Searchingfor watch
the system on the watch, please follow the steps below to resume the updates.
1. Remove the battery from the compartment and wait for at least 15 seconds before re-installation.
2. Return the battery to the compartment. Make sure the battery should have enough energy;
otherwise please insert a new battery instead of the original one.
3. Secure the lid by using the coin to make the lid back into the place. start system update displays
on the screen.
4. Start your phone with the application “Ssmart”.
5. Tap on to enter SYNC page.
6. Tap on CONNECT WITH WATCH, and then press the top (1) button on the watch. system update
and please wait display on the screen.
7. The watch and the application begin to synchronize and the system starts updating. Once the watch
completes updating, the screen turns off for about 1 minute, then goes back to the idle time mode.
SENSOR SETUP
With different sensor devices paired with the watch, the watch can be maximized to the highest performance for your exercise target, including chest belt and bike pod
(purchased separately). You can add a sensor before or after downloading exercise profiles.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Oregon Scientific SE900 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Oregon Scientific SE900 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.
The manual is 77.83 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
