589158
21
Zoom out
Zoom in
Previous page
1/30
Next page
21
GB
To attach the equipment:
1. Attach the bike mount to the right or left handlebar using
rubber grip, nut and bolt provided. Tighten until the bike
mount is fixed into place, using the rubber grip for a firmer
contact.
2. Attach the cadence sensor to a stationary point just behind
the pedal, using the rubber grip for a firmer contact. There
should be maximum 100cm (39 inches) between the sensor
and the bike mount, and less than 30 degrees vertical angle.
3. Attach the cadence magnet to a pedal so that it is directly
aligned with the sensor with less than 5mm (0.2 inches)
between.
4. Attach the speed sensor to either leg of the front forks, using
the rubber grip for a firmer contact. There should be
maximum 100cm (39 inches) between the sensor and the
bike mount, and less than 30 degrees vertical angle.
5. Attach the speed magnet on a spoke of the front wheel so that
it less than 5mm (0.2 inches) from the sensor.
6. Check and adjust as necessary, then snip the ends off the
clips so that no excess remains.
7. Fit the watch into the bike mount.
8. Press MODE on the watch to switch to BIKE Mode.
9. Press ST/SP/- to activate signal reception. The display
shows “- -“, then changes to 0 once a successful signal is
received.
10. Ride the bike a short distance to make sure signals are
being sent to the watch successfully.
11. You are now ready to begin your trip.
The watch can work with one or both sensors.
When the display shows a low battery icon
(see
‘Battery’ section) replace the battery for the corresponding unit.
STEP 2: ENTER WHEEL CIRCUMFERENCE
You must set the bike’s wheel circumfer-
ence on the watch so it can accurately
calculate your speed and distance. If you
do not know the bike’s wheel circumfer-
ence, you can check the manufacturer’s
specifications or measure it by marking
the wheel where it touches the ground,
and then rotating the wheel once fully along the ground.
Measure the difference between the two marks.
Most wheels have their specifications written on them.
To specify this information on the watch:
1. Press MODE to switch to the BIKE Mode.
2. Press and hold FUNC/SET for 2 seconds.
3. Press SELECT/+ or ST/SP/- to change the circumference
(cm or inches, depending on the measurement unit you
selected in CLOCK Mode).
4. Press FUNC/SET to save your changes.
You can also use the PC software for this operation (see
PC section).
NOTE
NOTE
NOTE
NOTE
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific RX 109 series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific RX 109 series in the language / languages: English as an attachment in your email.

The manual is 2,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oregon Scientific RX 109 series

Oregon Scientific RX 109 series Additional guide - English, German - 2 pages

Oregon Scientific RX 109 series User Manual - German - 34 pages

Oregon Scientific RX 109 series Additional guide - Dutch - 2 pages

Oregon Scientific RX 109 series User Manual - Dutch - 36 pages

Oregon Scientific RX 109 series Additional guide - French - 2 pages

Oregon Scientific RX 109 series User Manual - French - 32 pages

Oregon Scientific RX 109 series Additional guide - Italian, Portuguese, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info