589248
16
Zoom out
Zoom in
Previous page
1/19
Next page
15
EN
If an RDS station is tuned, the VFD will read the station name (PS) approx. 3 seconds after the radio frequency is automatically
displayed. During that time, press the display / RDS button on the remote control continually and the VFD will read the following
services: Programme Type (PTY)----Frequency----Station Name (PS).
RDS is available only for the Europe. When using the unit in North America or other markets that do not support RDS,
the RDS feature will not work if the remote control display / RDS button is pressed; the message, "NO RDS", will show on the
VFD.
TROUBLESHOOTING
Use this troubleshooting guide to help remedy any difficulties you may be experiencing while using the CD Micro System.
Should any problem persist after you have checked these symptoms, consult your nearest Oregon Scientific dealer.
Why is there no power coming from the unit? And when there is power why is it switching off automatically?
Ensure the AC power cord is connected to wall outlet and all cables and speaker cable wires are properly connected. If the
player is not used, i.e., no button is pressed for 30 minutes, it automatically switches to standby mode (Auto Power Off). Press
the button to switch the player on again. The plugs and jacks may be dirty, affecting the connections. Ensure the cables and
plugs are cleaned and properly connected and firmly established.
Why is the unit not playing CDs?
The disc may not be secured in place. Take the disc out and re-insert if necessary. If the disc is dirty, clean it with a soft, lint-free
cloth and try playing the disc again. If it still does not play, than may mean it is scratched or is not of the format that is compatible
with the player. There may be excess moisture condensed inside the player's lens. Leave the player turned off for a few hours
until moisture evaporates, then turn on.
How come the buttons on the main unit and / or remote control do not activate the functions they control?
The player may not be operating properly due to lightning, interference, static electricity or some other external factors. Turn the
unit off, disconnect the power plug and then re-connect. Try changing the battery cell on the remote control. Your unit has built-
in protection against overload or overheating. If the unit switches off in this case, wait a few minutes and power on again. If the
buttons on the unit and remote control still do not activate the functions they control even when corrective actions are taken, the
buttons may be damaged or there may be some other cause of malfunction. Take the unit to a qualified Oregon Scientific dealer
for servicing.
Why do the speakers and subwoofer not power on at all?
Ensure the power cord is firmly plugged into the power outlet. On rare occasions, the speakers may not operate due to data
signal interference or static electricity. Turn the power off and unplug the unit from the power outlet briefly, and then plug it in
again so it will reset itself and turn the speaker on.
How come there is hardly any sound or no sound coming from one or any speakers or subwoofer at all?
Check to ensure the power is on and increase the volume. Make sure the speakers are connected properly and that the unit is
not on mute. Check to see that the light / dark grey speaker and subwoofer cable wires are matching their appropriate light / dark
grey terminals. Data signal interference or static electricity may disrupt the signal reception. Switch the unit off, wait a few
seconds, and turn the unit back on. The speaker cable wires may be twisted or tangled up in knots, causing interference or
disruptions / distortion to audio reception. Untangle or untwist the cable wires should allow for clearer audio reception.
How do I eliminate the severe hum, distortion or noise that is coming from the speakers and subwoofer?
The cables and jacks may be dirty, affecting the connections and thus causing sound distortion. Wipe clean. In some cases,
volume might not be appropriately adjusted. Adjusting the volume will help to clear any hum or distortion. There may be excess
moisture condensed inside the speakers or that might affect their ability to produce audio, especially after turning on heating in
the room, if the room is damp, or if the speakers are brought directly from a cold to a warm place. In this case, leave the system
off for a few hours until moisture evaporates, unplug the AC power cord and then plug it in again.
NOTE
+06(QJ5B1RYB 11/10/2005, 08:13 PM15
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific HMS388 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific HMS388 in the language / languages: English as an attachment in your email.

The manual is 3,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oregon Scientific HMS388

Oregon Scientific HMS388 User Manual - German - 19 pages

Oregon Scientific HMS388 User Manual - Dutch - 18 pages

Oregon Scientific HMS388 User Manual - French - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info