564456
92
Zoom out
Zoom in
Previous page
1/93
Next page
EN-1
CONTENTS
Usage Notice .....................................................................................2
Safety Instructions ................................................................................................................. 2
Introduction .......................................................................................5
Projector Features ................................................................................................................. 5
Package Contents ................................................................................................................. 6
Projector Overview ................................................................................................................ 7
Using the Product .............................................................................9
Control Panel ......................................................................................................................... 9
Connection Ports ................................................................................................................. 10
Remote Control ................................................................................................................... 12
Installing the Batteries ......................................................................................................... 15
Remote Control Operation ................................................................................................... 16
Connection ......................................................................................17
Connecting a computer or monitor ...................................................................................... 19
Connecting Video source devices ....................................................................................... 21
Operation .........................................................................................24
Powering On/Off the Projector ............................................................................................. 24
Adjusting the Projector Height ............................................................................................. 25
Adjusting the Projector Zoom and Focus ............................................................................ 25
Adjusting Projection Image Size .......................................................................................... 26
Menu Operation ................................................................................................................... 30
Controlling the projector through a LAN environment ......................................................... 50
Controlling the projector through a web browser ................................................................. 54
Displaying images through Optoma Presenter .................................................................... 61
Displaying pictures with a USB storage device ................................................................... 65
Appendix ..........................................................................................69
Replacing the Dust Filter ..................................................................................................... 69
Replacing the Lamp .............................................................................................................70
Ceiling mount installation .....................................................................................................72
Compatibility Modes ............................................................................................................73
IR Code ............................................................................................................................... 76
Telnet Commands ............................................................................................................... 78
PJLink commands ............................................................................................................... 79
AMX Device Discovery commands ..................................................................................... 80
RS232 Commands and Protocol Function List .................................................................... 81
Troubleshooting ................................................................................................................... 87
Optoma Global Offices ........................................................................................................ 89
Regulation & Safety Notices ................................................................................................ 92
EN-2
Usage Notice
Safety Instructions
Read all of these instructions before you operate your projector and save for future reference.
1. Read instructions
All the safety and operating instructions should be read before the
appliance is operated.
2. Notes and warnings
All notes and warnings in the operating instructions should be adhered
to.
3. Cleaning
Unplug the projector from the wall socket before cleaning. Use a damp
cloth for cleaning the projector housing. Do not use liquid or aerosol
cleaners.
4. Accessories
Do not place this product on an unstable cart, stand, or table. The product
may fall,
causing serious damage to the product.
Keep the plastic packing materials (from the projector, accessories and
optional parts) out of the reach of children as these bags may result in
death by suffocation. Be particularly careful around the small children.
5. Ventilation
The projector is equipped with ventilation holes (intake) and ventilation holes
(exhaust).
Do not block or place anything near these slots, or internal heat
build-up may occur,
causing picture degradation or damage to the
projector.
6. Power sources
Check that the operating voltage of your unit is identical with the voltage of
your local
power supply.
7. Servicing
Do not attempt to service this projector yourself. Refer all servicing to
qualified service personnel.
8. Replacement parts
When replacement parts are required, be sure that the replacement
parts are
specified by the manufacture. Unauthorized substitutions may
result in fire, electric
shock or other hazards.
EN-3
9. Moisture Condensation
Never operate this projector immediately after moving it from a cold
location to a warm one. When the projector is exposed to such a
change in temperature, moisture may condense on the lens and the
crucial internal parts. To prevent the unit from possible damage, do not
use the projector for at least 2 hours when there is an extreme or
sudden change in temperature.
EN-4
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector. Please
confirm your AC plug type with the graphics below and ensure that the proper AC Power Cord is
used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales
dealer. This projector is equipped with a grounding type AC line plug. Please ensure that your
outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly
recommend using a video source device also equipped with a grounding type AC line plug to
prevent signal interference due to voltage fluctuations.
For Australia and
Mainland China
For the U.S.A. and Canada
For the U.K.
Ground
For Continental Europe
Ground
Ground
Ground
EN-5
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user
- friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
Single chip 0.55" Texas Instruments DLP
®
technology (XGA model)
Single chip 0.65" Texas Instruments DLP
®
technology (WXGA/1080P
model)
XGA (1024 x 768 pixels)
WXGA (1280 x 800 pixels)
1080P (1920 x 1080 pixels)
Compatibility with Macintosh
®
computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
RS-232 connector for serial control
Quick Resume feature
Eco
+
mode for more economic usage
Full 3D
HDMI compatibility
PJLink
TM
compatibility
Support wireless dongle via internal power of VGA 2
LAN Settings allowing management of projector status from a remote
computer
LAN display 4-1 (maximum 4PC/ NB display to 1 projector)
LAN display 1-M available (1PC/ NB can display to maximum 8
projectors at the same time)
USB display supports computer connection via USB B type to A type
cable
Note
The information in this manual is subject to change without notices.
The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
EN-6
Package Contents
When you unpack the projector, make sure you have all these components:
Note
For European warranty information please visit www.optomaeurope.com
Due to the difference in applications for each country, some regions may have
different accessories.
Contact your dealer immediately if any items are missing, appear damaged, or if the
unit does not work
.
Save the original shipping carton and packaging material; they will come in handy if
you ever need to ship your unit. For maximum protection, repack your unit as it was
originally packed at the factory.
Projector AC Power Cord VGA Cable (D-SUB to D-SUB)
Remote Control with
Laser Pointer & batteries
(AAA *2 PCS)
Carry Bag (optional for
certain models)
Dust filter (depending on
region)
Documentation:
5User's Manual
5Warranty Card
5Quick Start Card
5WEEE Card
(for EMEA only)
EN-7
Projector Overview
Front View
Front adjustment foot Speaker
Projection lens Ventilation holes
Focus ring Control panel
Front IR remote control sen-
sor
Zoom ring
Security bar Top cover
9
10
1
2 3
4
5
8
6 7
1 6
2 7
3
8
4 9
5
10
EN-8
Rear View
Bottom View
Ceiling mount holes
Rear adjustment feet
Note
This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package.
Contact your dealer for information to mount the projector on a ceiling.
Optional air dust Rear IR remote control sensor
AC power socket Optional wireless dongle slot
Connection ports Speaker
Kensington lock Ventilation holes
1
3
8
2
4
5 6
7
1 5
2 6
3 7
4
8
2
1
1
2
2
EN-9
Using the Product
Control Panel
Keystone ( / )
Manually correct distorted images resulting from an angled projection.
SOURCE
Switch between input signals.
HELP
Display Help menu.
MENU
Display or exit the on-screen display menus.
TEMP (Temp LED indicator)
Refer to “LED Indicator Messages” on page 88.
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages” on page 88.
POWER (Power LED indicator)
Refer to “LED Indicator Messages” on page 88.
Four directional buttons
Use four directional buttons to select items or make adjustments to your
selection.
Re-SYNC
Automatically synchronize the projector to the input source.
Power
Turn the projector on or off.
ENTER
Confirm your item selection.
8
9
1
1
2
3
10
4
5
6
7
11
1
2
3
4
5
6
7
8
9
10
11
EN-10
Connection Ports
RS-232C
When operating the projector via a computer, connect this to the
controlling computer's RS-232C port.
VGA-OUT
Connect to an external monitor.
In Eco mode (Standby), VGA-OUT is disabled.
In Active mode (Standby), VGA-OUT is enabled.
S-VIDEO
Connect S-Video output from video equipment to this jack.
MOUSE/SERVICE
This connector supports firmware update, remote mouse and page up/
down.
HDMI
Connect HDMI output from video equipment to this jack.
DVI-D
Connect DVI-D output from computer to this jack.
DISPLAY
USB display supports computer connection via USB B type to A type
cable.
1
2
3
5
4
6
7
8
9
11
10
12
13
14
15
16
17
1
2
3
4
5
6
7
EN-11
RJ-45
For LAN display/network control and web server.
FLASH DRIVE
This connector supports USB flash drive display.
12V OUT
12V DC out
MIC
Microphone input jack.
AUDIO OUT
Connect to a speaker or other audio input equipment.
AUDIO-IN 1/AUDIO-IN 2
Connect an audio output from a computer to this jack.
AUDIO-IN 3 (L/R)
Connect an audio output from a video device to this jack.
VIDEO
Connect composite video output from video equipment to this jack.
VGA2-IN / YPbPr /
Connect image input signal (analog RGB or component) to this jack.
Support wireless dongle via internal power of VGA 2.
VGA1-IN / YPbPr
Connect image input signal (analog RGB or component) to this jack.
8
9
10
11
12
13
14
15
16
17
EN-12
Remote Control
Power
Turn the projector on or off.
Source
Switch between input signals.
Left mouse
Perform the left button of the mouse when mouse mode is activated.
Four directional buttons
Use four directional buttons to select items or make adjustments to your
selection.
"UP" key: When menu is off, up key for emulation of USB mouse.
"Left" key: When menu is off, left key for emulation of USB mouse.
"Right" key: When menu is off, right key for emulation of USB mouse.
"Down" key: When menu is off, down key for emulation of USB mouse.
Page-
Perform page down function when mouse mode is activated.
Keystone (+/-)
Manually correct distorted images resulting from an angled projection.
5
4
7
1
3
2
6
9
8
11
10
12
27
19
17
14
13
15
16
21
22
20
23
24
25
26
18
1
2
3
4
5
6
EN-13
Brightness
Display the setting bar for adjustment of brightness.
Freeze
Freeze the projected image.
HDMI
Display HDMI signal.
(This function will not work if product does not have HDMI.)
S-Video
Display S-Video signal.
Eco+
Brightness mode menu on/off.
VGA
Switch input source to VGA1 or VGA2 by sequence.
Switch
Switch to mouse mode when the on-screen menus are close.
User
User definable key for customized function.
Re-SYNC
Automatically synchronize the projector to the input source.
Right mouse
Perform the right button of the mouse when mouse mode is activated.
Enter
Confirmed selections.
Enter key for emulation of USB mouse via USB.
Laser
Aim the remote at the viewing screen, press and hold this button to acti-
vate the laser pointer.
Page+
Perform page up function when mouse mode is activated.
Volume (+/-)
Adjust the volume level.
Menu
Display on-screen display menus.
Zoom
Magnifies or reduces the projected picture size.
AV mute
Momentarily turns off/on the audio and video.
Video
Display video signal.
3D
Turn on or off 3D function.
USB
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
EN-14
Switch to mouse mode when the on-screen menus are close.
Numbered keypad
Press 0 to 9 to enter a password when required.
Note
Remote Control (IR) or Remote Control with Laser Pointer (depending on region). See
Appendix for the Remote with Laser Pointer.
Using the remote mouse control
The capability of operating your computer with the remote control gives you
more flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to
using the remote control in place of your computers mouse. See
“Connecting a computer” on page 19 for details.
2. Set the input signal to VGA1 or VGA2.
3. Press USB or Switch on the remote control to switch to mouse mode
when the on-screen menus are close. An icon appears on the screen to
indicate the activation of the mouse mode.
4. Perform the desired mouse controls on your remote control.
To move the cursor on the screen, press / / / .
To left-click, press L.
To right-click, press R.
To return to the normal mode, press Switch again.
Note
HDMI also supports mouse function.
27
EN-15
Installing the Batteries
1. Open the battery cover in the
direction shown.
2. Install batteries as indicated by
the
diagram inside the compartment.
3. Close the battery cover into
position.
Caution
Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
Keep the batteries out of the reach of children. There is a danger of death by accidentally
swallowing the batteries.
Remove batteries from remote control when not using for extended periods.
Do not dispose of the used batteries along with household waste. Dispose of used
batteries according to local regulations.
Danger of explosion may happen if batteries are incorrectly replaced. Replce all the
batteries with new ones.
Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry
place.
If suspect battery leakage, wipe out the leakage and then replace new batteries. If the
leakage adheres to your body or clothes, rinse well with water immediately.
EN-16
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
Operating the projector
from the front
Operating the projector
from the rear
Note
The remote control may not operate when there is sunlight or other strong light such
as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively high temperature or
humidity.
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
7m
5m
15
15
10m
7m
5m
15
15
10m
EN-17
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
1. ................................................................... VGA cable (D-Sub to D-Sub)
2. .................................................................. *USB cable (B type to A type)
3. .........................................................................................*Audio cable
4. .........................................................................................*DVI-D cable
5. ................................................................................*VGA to DVI-A cable
6. .......................................................*VGA (D-Sub) to HDTV (RCA) cable
7. .........................................................................................*S-Video cable
8. .........................................................................................*HDMI cable
9. ......................................................................................*Audio L/R cable
1
2
3
4
1
5
6
7
8
9
12
10
3
11
EN-18
10. .......................................................................... *Composite video cable
11. .......................................................................................*USB flash drive
12. .............................................................. *Microphone 3.5 mini jack cable
Note
Due to the difference in applications for each country, some regions may have
different accessories.
(*) Optional Accessory
EN-19
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them
to both IBM
®
compatible and Macintosh
®
computers. A Mac adapter is
needed if you are connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output
socket of the computer.
2. Connect the other end of the VGA cable to the VGA1/YPbPr or VGA2/
YPbPr signal input socket on the projector.
Important
Many notebooks do not turn on their external video ports when connected to a
projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display
on/off. Locate a function key labeled CRT/LCD or a function key with a monitor
symbol on the notebook. Press FN and the labeled function key simultaneously. Refer
to your notebook's documentation to find your notebook's key combination.
EN-20
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the
screen, you can connect the VGA-OUT signal output socket on the projector
to an external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in “Connecting a
computer” on page 19.
2. Take a suitable VGA cable (only one supplied) and connect one end of
the cable to the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to
DVI-A cable and connect the DVI end of the cable to the DVI input
socket of the video monitor.
3. Connect the other end of the cable to the VGA-OUT socket on the
projector.
VGA-OUT loop through:
During working mode:
1. If VGA1 is projecting out, VGA-OUT source will be VGA1.
2. If VGA2 is projecting out, VGA-OUT source will be VGA2.
3. If VGA1 and VGA2 are all have sources, default VGA-OUT is VGA1.
4. If none of VGA1 and VGA2 is projecting out, VGA-OUT is disabled.
During Standby
1. VGA-OUT will keep the latest display VGA source signal. Default VGA-
OUT is VGA1.
2. If the projector is in Power Mode (Standby) < 0.5W, VGA-OUT is
disabled.
EN-21
Connecting Video source devices
You can connect your projector to various Video source devices that provide
any one of the following output sockets:
HDMI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one
of the above connecting methods, however each provides a different level of
video quality. The method you choose will most likely depend upon the avail-
ability of matching terminals on both the projector and the Video source
device as described below:
Terminal name Terminal appearance Reference Picture quality
HDMI HDMI “Connecting an
HDMI source
device” on
page 22
Best
Component
Video
VGA1/YPbPr or
VGA2/YPbPr
“Connecting a
Component Video
source device” on
page 22
Better
S-Video S-VIDEO “Connecting an
S-Video source
device” on
page 23
Good
Video VIDEO “Connecting a
composite Video
source device” on
page 23
Normal
EN-22
Connecting an HDMI source device
Examine your Video source device to determine if it has a set of unused
HDMI output jacks available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to
the device.
To connect the projector to an HDMI source device:
1. Take an HDMI cable and connect one end to the HDMI output jack of the
HDMI source device.
2. Connect the other end of the HDMI cable to the HDMI jack on the
projector.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused
Component Video output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to
the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the
Video source device. Match the color of the plugs to the color of the
sockets; green to green, blue to blue, and red to red.
2. Connect the other end of the cable (with a D-Sub type connector) to the
VGA1/YPbPr or VGA2/YPbPr socket on the projector.
Important
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned
on and operating correctly. Also check that the signal cables have been connected
correctly.
EN-23
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video
output socket available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to
the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output
socket of the Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on
the projector.
Important
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned
on and operating correctly. Also check that the signal cables have been connected
correctly.
If you have already made a Component Video connection between the projector and
this S-Video source device using Component Video connections, you need not
connect to this device using an S-Video connection as this makes an unnecessary
second connection of poorer picture quality. See “Connecting Video source devices”
on page 21 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused
composite Video output sockets available:
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to
the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output
socket of the Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the
projector.
Important
If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned
on and operating correctly. Also check that the signal cables have been connected
correctly.
You need only connect to this device using a composite Video connection if
Component Video and S-Video inputs are unavailable for use. See “Connecting Video
source devices” on page 21 for details.
EN-24
Operation
Powering On/Off the Projector
Powering On the Projector:
1. Connect the AC power cord and relevant peripheral signal cable(s) to
the projector.
2. Press to turn on the projector.
The projector takes a minute or so to warm up.
3. Turn on your source (computer, notebook, DVD, etc.). The projector
automatically detects your source.
If you are connecting multiple sources to the projector
simultaneously, press SOURCE on the projector or Source on the
remote control to select your desired signal or press your desired
signal key on the remote control.
Warning
Never look into the lens when the lamp is on. This can damage your eyes.
This focal point concentrates high temperature. Do not place any object near it to
avoid possible fire hazard.
Powering Off the Projector:
1. Press to turn off the projector lamp. You will see a message "Power
off? Press Power again" appear on the screen.
2. Press again to confirm.
The cooling fans continue to operate for cooling cycle.
When
the Power LED becomes steady red, the projector has entered
stand-by mode.
If you want to turn the projector back on, you must wait until the
projector has completed the cooling cycle and has entered stand-by
mode. Once in stand-by mode, simply press to restart the
projector.
3. Disconnect the AC power cord from the electrical outlet and the
projector.
4. Do not turn on the projector right after power off.
Warning
When Quick Resume is on, if turning off the projector accidentally and Quick
Resume selected within a period of 100 seconds, the projector will instantly power on
again.
When Quick Resume is off, if turning off the projector, users need to wait until the
cooling process is finished and then restart the projector. It will take a few minutes
because the fan will keep running until the internal temperature is reduced to certain
level.
EN-25
Adjusting the Projector Height
The projector is equipped with three adjustment feet to adjust the image
height.
1. To raise or lower the image, turn the front adjustment foot.
2. To level the image on the screen, turn the rear adjustment feet to fine-
tune the height.
Note
To avoid damaging the projector, make sure that the adjustment feet are fully
retracted before placing the projector in its carrying case.
Adjusting the Projector Zoom and
Focus
1. Focus the image by rotating the focus ring. A still image is recommended
for focusing.
2. Adjust the image size by rotating the zoom ring.
Adjustment feet
Focus ring
Zoom ring
EN-26
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection
distance.
XGA model
WXGA model
Screen size
Diagonal
[inch (cm)]
4 : 3 Screen
Projection distance [feet (m)]
Image height
[inch (cm)]
Vertical offset
[inch (cm)]
(min. zoom) (max. zoom)
30 (76) 2.7 (0.85) 4.5 (1.4) 18 (46) 2.7 (7)
40 (102) 3.7 (1.1) 5.9 (1.8) 24 (61) 3.6 (9)
60 (152) 5.6 (1.7) 8.9 (2.7) 36 (91) 5.4 (14)
80 (203) 7.4 (2.3) 11.9 (3.6) 48 (122) 7.2 (18)
100 (254) 9.3 (2.8) 14.8 (4.5) 60 (152) 9.0 (23)
120 (305) 11.2 (3.4) 17.8 (5.4) 72 (183) 10.8 (27)
150 (381) 13.9 (4.3) 22.3 (6.8) 90 (229) 13.5 (34)
200 (508) 18.6 (5.7) 29.7 (9.1) 120 (305) 18.0 (46)
250 (635) 23.2 (7.1) 37.2 (11.3) 150 (381) 22.5 (57)
300 (762) 27.9 (8.5) 44.6 (13.6) 180 (457) 27.0 (69)
Screen size
Diagonal
[inch (cm)]
16:10 Screen
Projection distance [feet (m)]
Image height
[inch (cm)]
Vertical offset
[inch (cm)]
(min. zoom) (max. zoom)
30 (76) 3.0 (0.9) 4.6 (1.4) 16 (40) 2.4 (6)
40 (102) 4.0 (1.2) 6.0 (1.8) 21 (54) 3.2 (8)
60 (152) 6.0 (1.8) 9.0 (2.7) 32 (81) 4.8 (12)
80 (203) 8.0 (2.4) 12.0 (3.7 42 (108) 6.4 (16)
100 (254) 10.0 (3.1) 15.0 (4.6) 53 (135) 7.9 (20)
120 (305) 12.0 (3.7) 18.0 (5.5) 64 (162) 9.5 (24)
150 (381) 15.0 (4.6) 22.5 (6.9) 79 (202) 11.9 (30)
200 (508) 20.0 (6.1) 30.0 (9.2) 106 (269) 15.9 (40)
250 (635) 25.0 (7.6) 37.5 (11.4) 132 (336) 19.9 (50)
300 (762) 30.0 (9.2) 45.0 (13.7) 159 (404) 23.8 (61)
Maximum zoom
Minimum zoom
Projection distance
Center of lens
Screen
Vertical offset
EN-27
1080P model
Note
Position the projector in a horizontal position; other positions can cause heat build-
up and damage to the projector.
Keep a space of 30 cm or more between the sides of the projector.
Do not use the projector in a smoky environment. Smoke residue may build-up on
critical parts and damage the projector or its performance.
Consult with your dealer for special installation such as suspending from a ceiling.
Screen size
Diagonal
[inch (cm)]
16:9 Screen
Projection distance [feet (m)]
Image height
[inch (cm)]
Vertical offset
[inch (cm)]
(min. zoom) (max. zoom)
30 (76) 3.0 (0.9) 4.6 (1.4) 15 (37) 2.2 (6)
40 (102) 4.0 (1.2) 6.0 (1.8) 20 (50) 2.9 (7)
60 (152) 6.0 (1.8) 9.0 (2.7) 29 (75) 4.4 (11)
80 (203) 8.0 (2.4) 12.0 (3.7 39 (100) 5.9 (15)
100 (254) 10.0 (3.1) 15.0 (4.6) 49 (125) 7.4 (19)
120 (305) 12.0 (3.7) 18.0 (5.5) 59 (149) 8.8 (22)
150 (381) 15.0 (4.6) 22.5 (6.9) 74 (187) 11 (28)
200 (508) 20.0 (6.1 30.0 (9.2) 98 (249) 14.7 (37)
250 (635) 25.0 (7.6) 37.5 (11.4) 123 (311) 18.4 (47)
300 (762) 30.0 (9.2) 45.0 (13.7) 147 (374) 22.1 (56)
EN-28
Adjusting the position using the vertical lens shift
function
If the projector is not positioned right in front of the center of the screen, you
can adjust the vertical position of projected image by moving the vertical lens
ring within the shift range of the lens.
1. Lens shift adjustment for XGA
The display position can be shifted upward up to 6.5% elevation of the
display. (When turn the vertical lens shift ring to the right (left), the
display moves up (down)).
2. Lens shift adjustment for WXGA
The display position can be shifted upward up to 14.5% elevation of the
display. (When turn the vertical lens shift ring to the right (left), the
display moves up (down)).
Lens shift adjustable range
6.5%
Shift range
Lens shift center position
Shift to top
1V
0.15V
0.065V
Lens shift adjustable range
14.5%
Shift range
Lens shift center position
Shift to top
0.145V
1V
0.12V
EN-29
3. Lens shift adjustment for 1080P
The display position can be shifted upward up to 17% elevation of the
display. (When turn the vertical lens shift ring to the right (left), the
display moves up (down)).
Attention
Please note the following s when using the projector.
Do not touch the lens while it is moving as this could cause injury to the fingers.
Never allow children to touch the lens.
Shift to top
Lens shift center position
Shift range
17%
Lens shift adjustable range
0.17V
1V
0.15V
EN-30
Menu Operation
The projector has multilingual on-screen display menus that allow you to
make image adjustments and change a variety of settings.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Projector Keypad.
2. When OSD is displayed, use / key to select to select any item in the
main menu. While making a selection on a particular page, press
or
“Enter key to enter sub menu.
3. Use / key to select the desired item and press / /”Enter” key to
enter the Single-Item-Menu.
4. Use the / key to adjust the value. Use “Enter” to confirm the
selection.
5. Select the next item to be adjusted in the sub menu and adjust as
described above.
6. Press ”Menu” to go back to Sub-Menu.
7. To exit, press “Menu” again. The OSD menu will close and the projector
will automatically save the new settings.
Main Menu
Sub-Menu
Settings
Single-Item-
Menu
EN-31
Menu tree
Main Menu Sub-Menu
Single-Item
Menu
IMAGE
Display Mode
Presentation /
Bright / Movie /
sRGB /
Blackboard /
DICOM SIM /
User / 3D
Brightness
Contrast
Sharpness
Color
Tint
Advanced
Gamma
1.8 / 2.0 / 2.2 /
2.6 / Film /Video
/ Graphic
BrilliantColor™
Color Temp.
Warm / Medium
/ Cold
Color Settings
Red
Hue / Saturation
/ Gain
Green
Hue / Saturation
/ Gain
Blue
Hue / Saturation
/ Gain
Cyan
Hue / Saturation
/ Gain
Magenta
Hue / Saturation
/ Gain
Yellow
Hue / Saturation
/ Gain
White
Red / Green /
Blue
Reset
Exit
Color Space
Auto / RGB
(0~255) / RGB
(16~235) YUV
EN-32
IMAGE
Advanced
Signal
Automatic On / Off
Phase (VGA)
Frequency
(VGA)
H. Position
(VGA)
V. Position
(VGA)
Exit
Exit
Reset Yes / No
DISPLAY
Format
XGA:
4:3 / 16:9 /
Native / Auto
WXGA/1080P:
4:3 / 16:9 or
16:10 / LBX /
Native / Auto
Edge Mask
Zoom
Image Shift
H
V
V Keystone
Auto Keystone On / Off
3D
3D Mode DLP-Link / IR
3D--->2D 3D / L / R
3D Format
Auto / SBS / Top
and Bottom /
Frame
Sequential
3D Sync Invert On / Off
SETUP
Language
Projection
Menu Location
Screen Type
16: 10/16:9
(WXGA)
EN-33
SETUP
Security
Security On / Off
Security Timer
Month / Day /
Hour
Change Password
Exit
Projector ID
Audio Settings
Internal Speaker On / Off
Mute On / Off
Volume
Audio
Mic
Audio Input
Default / Audio
1 / Audio 2 /
Audio 3
Advanced
Logo
Default / Neutral
/ User
Logo Capture
Closed Captioning Off / CC1 / CC2
Exit
Network
LAN Settings
Network Status
Connected /
Disconnected
MAC Address
DHCP On / Off
IP Address
Subnet Mask
Gateway
DNS
Exit
WLAN Settings
WLAN On / Off
Network Status
Connected /
Disconnected
MAC Address
IP Address
SSID
Connection
Mode
Infrastructure /
Access Point
Exit
Control Settings
Crestron On / Off
Extron On / Off
PJ Link On / Off
AMX Device
Discovery
On / Off
Telnet On / Off
HTTP On / Off
Exit
EN-34
OPTIONS
Input Source
VGA1 / VGA2 /
Video / S-video /
HDMI / DVI /
Flash drive/
Network
display/ USB
display
Source Lock On / Off
High Altitude On / Off
Information Hide On / Off
Keypad Lock On / Off
Test Pattern
None / Grid /
White
12V Trigger
On / Off / Auto
3D
IR Function
On / Front /
Back / Off
Background Color
Black / Red /
Blue / Green /
White
Remote Settings
Display Mode /
Format / 3D
Sync Invert /
Mute / Test
Pattern / DVI /
VGA2 / Network
Display
Advanced
Direct Power On On / Off
Signal Power On On / Off
Auto Power Off
(min.)
Sleep Timer (min.)
Quick Resume On / Off
Power Mode
(Standby)
Active / Eco
Lamp Settings
Lamp Hour
Lamp Reminder On / Off
Brightness Mode
Bright /
Dynamic / Eco
+
Lamp Reset Yes / No
Exit
Optional Filter
Settings
Optional Filter
Installed
Yes / No
Filter Usage Hours
Filter Reminder
Off / 300hr /
500hr / 800hr /
1000hr
Filter Reset Yes / No
Exit
Reset Yes / No
EN-35
IMAGE
Display Mode
There are many factory presets optimized for various types of images.
Presentation: Good color and brightness from PC input.
Bright: Maximum brightness from PC input.
Moive: For home theater.
sRGB: Standardised accurate color.
Blackboard: This mode should be selected to achieve optimum color
settings when projecting onto a blackboard (green).
User: Users settings.
DICOM SIM: Recommended for DICOM format files in
simulation mode.
3D: Recommended setting for 3D mode. Any further adjustments by the
user in 3D will be saved in this mode for further use.
Note
DCIM SIM option is only for training or reference. It not used for actual diagnosis.
DICOM represents for the Digital Imaging and Communications in Medicine. This is a
standard created by the American College of Radiology and the National Electrical
Manufacturers Association. This standard specifies the method of digital image data
to be transferred from one system to another.
Brightness
Brighten or darken the image.
Contrast
EN-36
Set the difference between light and dark areas.
Sharpness
Sharpen or soften the image.
Color
Adjust a video image from black and white to fully saturated color.
Tint
Shift colors toward red or green.
Note
“Color” and “Tint” functions are only supported under Video mode.
Advanced
Gamma
This allows you to choose a degamma table that has been fine-tuned to bring
out the best image quality for the input.
Film: for home theater.
Video: for video or TV source.
Graphics: for image source.
2.2: for PC or computer source.
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and system
level enhancements to enable higher brightness while providing true, more
vibrant colors in picture. The range is from “1” to “10”. If you prefer a stronger
enhanced image, adjust toward the maximum setting. For a smoother, more
natural image, adjust toward the minimum setting.
EN-37
Color Temp.
If set to cold temperature, the image looks more blue. (cold image)
If set to medium temperature, the image maintains normal colorings for
white.
If set to warm temperature, the image looks more red. (warm image)
Color Settings
Press / /“Enter” key to enter the next menu as below and then use / /
/
key to select color. Press “Enter” to finalize the selection.
Red/Green/Blue/Cyan/Magenta/Yellow/White: Use / to toggle Hue/
Saturation/Gain and then use / to adjust the value.
Reset: Choose “Yes” to return the factory default settings for color
adjustments.
Color Space
Select an appropriate color matrix type from AUTO, RGB, RGB (0-255)(*),
RGB (16-235)(*) or YUV.
Note
(*) for HDMI only.
Signal
Automatic: Automatically selects the singal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not automatic,
the phase, frequency items will appear for user to manually tune and
saved in settings after that for next time projector turns off and on again.
Phase: Synchronize the signal timing of the display with the graphic
card. If the image appears to be unstable or flickers, use this function to
correct it.
Frequency: Change the display data frequency to match the frequency
of your computer’s graphic card. Use this function only if the image
appears to flicker vertically.
H. Position: Adjust the image left or right within the projection area.
V. Position: Adjust the image up or down within the projection area.
EN-38
Reset
Return the display parameters on IMAGE menu to the factory default set-
tings.
EN-39
DISPLAY
Format
Use this function to choose your desired aspect ratio.
For XGA model:
For WXGA model:
16:9 or 16:10 depend on “Screen Type” setting.
16:10 Screen
Source 480i/p 576i/p 1080i/p 720p
4:3 1024x768 center
16:9 1024x576 center
Native Displays the original image without any scaling.
Auto (Default) If source is 4:3, auto resize to 1024 x 768.
If source is 16:9 auto resize to 1024 x 576.
If source is 15:9 auto resize to 1024 x 614.
If source is 16:10 auto resize to 1024 x 640.
16 : 10
screen
480i/p 576i/p 1080i/p 720p PC
4:3 1066 x800 center
16:10 1280x800 center
LBX 1280x960 center, then get the central 1280x800 image to display.
Native 1:1 mapping
centered
1:1 mapping
display 1280 x
800
1280x720
Centered
1:1 mapping
centred
Auto (Default) Input source will be fit into 1280x800 display area and be kept its
original aspect ratio.
If source is 4:3, auto resize to 1066 x 800.
If source is 16:9 auto resize to 1280 x 720.
If source is 15:9 auto resize to 1280 x 768.
If source is 16:10 auto resize to 1280 x 800.
EN-40
16:9 Screen
For 1080P model:
Edge Mask
Edge Mask function removes the noise in a video image. Overscan the
image to remove video encoding noise on the edge of video source.
Note
Each I/O has different setting of “Edge Mask”.
“Edge Mask” and “Zoom” can’t work at same time.
Zoom
Zoom in and out the images.
Image Shift
Shift the projected image position horizontally and vertically.
V Keystone
Adjust image distortion vertically. If the image looks trapezoidal, this option
can help make the image rectangular.
Note
16 : 9 screen 480i/p 576i/p 1080i/p 720p PC
4:3 960x720 center
16:9 1280x720 center
LBX 1280x960 center, then get the central 1280x720 image to display.
Native 1:1 mapping
centered
1:1 mapping
display 1280 x
720
1280x720
Centered
1:1 mapping
centred
Auto (Default) If this format is select, Screen type will auto become 16:9 (1280 x
720).
If source is 4:3, auto resize to 960 x 720.
If source is 16:9 auto resize to 1280 x 720.
If source is 15:9 auto resize to 1200 x 720.
If source is 16:10 auto resize to 1152 x 720.
16 : 9 screen 480i/p 576i/p 1080i/p 720p PC
4:3 1440x1080 center
16:9 1920x1080 center
LBX 1920x1440 center, then get the central 1920x1080 image to display.
Native 1:1 mapping centered
Auto (Default) If this format is select, Screen type will auto become 16:9 (1920 x
1080).
If source is 4:3, auto resize to 1440 x 1080.
If source is 16:9 auto resize to 1920 x 1080.
If source is 16:10 auto resize to 1920 x 1200 and cut 1920 x 1080
area to display.
EN-41
Keystone adjustment might affect the complete presentation of the OSD menu.
When adjusting the V Keystone, Auto Keystone will be set at "Off" automatically.
Auto Keystone
Automatically correct distorted images resulting from an angled projection.
3D
3D Mode
DLP Link: Select “DLP Link” to use optimized settings for DLP Link 3D
glasses.
IR: Select “IR” to use optimized settings for IR-based 3D glasses.
3D--->2D
3D: Select 3D format.
L: Select left eye data.
R: Select right eye data.
3D Format
SBS: Use this mode for “Side-by-side” format 3D content.
Top and Bottom: Use this mode for “Top and Bottom” format 3D content.
Frame Sequential: Use this mode for “Frame Sequential” format 3D
content.
3D Sync. Invert
Press the “On” to invert left and right frame contents.
Press the “Off” for default frame contents.
EN-42
SETUP
Language
Select the language used by the on-screen menu. Press / /“Enter” key to
enter the sub menu and then use the / / / key to select your preferred
language. Press “Enter” to finalize the selection.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-
down, in front of or behind the screen. Invert or reverse the image accord-
ingly.
Menu Location
Choose the menu location on the display screen.
Screen Type (for WXGA model only)
Choose the screen type from16:10 or 16:9.
Security
Security
On: Choose “On” to use security verification when the turning on the
projector.
Off: Choose “Off” to be able to switch on the projector without password
verification.
EN-43
Security Timer
Use this function to set the how long (Month/Day/Hour) the projector can be
used. Once this time has elapsed you will be requested to enter your pass-
word again.
Change Password
First time:
1. Press “Enter” to set the
password.
2. The password has to be 4 digits.
3. Use number button on the remote
to enter your new password and
then press “Enter” key to confirm
your password.
Change Password:
1. Press “Enter” to input old
password.
2. Use number button to enter
current password and then press
“Enter” to confirm.
3. Enter new password (4 digits in length) using the number buttons on the
remote, then press “Enter” to confirm.
4. Enter new password again and press “Enter” to confirm.
If the incorrect password is entered 3 times, the projector will
automatically shut down.
If you have forgotten your password, please contact your local office
for support.
Note
Password default value is “1234” (first time).
Projector ID
ID definition can be set up by menu (range 0~99), and allow user control an
individual projector by RS232.
Audio Settings
Internal Speaker
Use the internal speaker of projector.
Mute
Cut off the sound temporarily.
Volume
Adjust the volume level for Audio or Mic input source.
EN-44
Audio Input
Select audio input sources.
Advanced
Logo
Use this function to set the desired startup screen. If changes are made they
will take effect the next time the projector is powered on.
Default: The default startup screen.
Neutral: Neutral startup screen.
User: "User" is the screen that you captured.
Logo Capture
Capture the current projection screen as a start up screen.
Closed Captioning
Use this function to set the desired startup screen. If changes are made they
will take effect the next time the projector is powered on.
Off: select “Off” to turn off the closed captioning feature.
CC1:CC1 language: American English.
CC2:CC2 language (depending on the TV channel of the user):Spanish,
French, Portuguese, German, Danish.
Network
LAN Settings
Allow you to configure the wired LAN settings.
Network Status: Display the network connection status.
MAC Address: a read-only display of MAC Address.
DHCP: This protocol automatically assigns IP Addresses to networked
devices.
On: Assign an IP address to the projector from an external DHCP
server automatically.
Off: Assign an IP address manually.
IP Address: Select an IP address.
Subnet mask: Select subnet mask number.
Gateway: Select the default gateway of the network connected to the
projector.
DNS: Select DNS number.
WLAN Settings
Allow you to configure the wireless LAN settings.
WLAN: Turn on or off wireless LAN function.
Network Status: Display the network connection status.
EN-45
MAC Address: a read-only display of MAC Address.
IP Address: a read-only display of IP Address.
SSID: Display the projector’s SSID information.
Connection Mode: Methods for connecting to wireless networks with Wi-
Fi enabled devices.
Control Settings
Allow you to configure nework settings.
Crestron: Turn on or off Crestron. *Note: Port 41794
Extron: Turn on or off Extron. *Note: Port 2023
PJ Link: Turn on or off PJ Link. *Note: Port 4352
AMX Device Discovery: Turn on or off AMX Device Discovery. *Note:
Port 9131
Telnet: Turn on or off Telnet. *Note: Port 23
HTTP: Turn on or off HTTP. *Note: Port 80
EN-46
OPTIONS
Input Source
Use this option to enable / disable input sources. Press / /“Enter” key to
enter the sub menu and select which sources you require. Press “Enter” to
finalize the selection. The projector will not search for inputs that are not
selected.
Source Lock
On: The projector will only search current input connection.
Off: The projector will search for other signals if the current input signal is
lost.
High Altitude
When “On” is selected, the fans will spin faster. This feature is useful in high
altitude areas where the air is thin.
Information Hide
On: Choose “On” to hide the info message.
Off: Choose “Off” to show the “searching” message.
EN-47
Keypad Lock
When the keypad lock function is “On”, the control panel will be locked how-
ever, the projector can be operated by the remote control. By selecting “Off”,
you will be able to reuse the control panel.
Note
To turn off the keypad lock, press and hold “Enter” key on top of the projector for 5
seconds.
Test Pattern
Display a test pattern. There are Grid, White pattern and None.
12V Trigger
Choose the setting from On / Off to Auto 3D to set 12V Trigger.
IR Function
Choose the setting from On / Front / Back to Off and then choose "Yes" to
apply the selection.
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or “White”,
screen when no signal is available.
Remote Settings
Allow user to define a short cut key on the remote control, and the function
item is selected in OSD menu.
Advanced
Direct Power On
Choose “On” to activate Direct Power mode. The projector will automatically
power on when AC power is supplied, without pressing the “ ” key on the
projector control panel or on the remote control.
Signal Power On
If Signal Power On is activated, the projector will turn on automatically when
VGA signal is detected.
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, when
there is no signal being sent to the projector. The projector will automatically
power off when the countdown has finished (in minutes).
EN-48
Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start, with or
without a signal being sent to the projector. The projector will automatically
power off when the countdown has finished (in minutes).
Quick Resume
If the projector is accidentally turned off, this feature allows the projector to
be instantly powered on again within 100 seconds of power down.
Power Mode (Standby)
Set whether the VGA-OUT function works when the projector is in standby
(powered off but connected to AC power).
Eco: The VGA-OUT and AUDIO-OUT functions will not work when the
projector is in standby.
Active: The VGA-OUT and AUDIO-OUT functions will work when the
projector is in standby.
Note
When Power mode (Standby) is set to Eco (<0.5W), the VGA output, Signal Power On,
Audio pass-through will be deactivated when the projector is in standby.
Lamp Settings
Lamp Hours
Display the projection time.
Lamp Reminder
Choose this function to show or to hide the warning message when the
changing lamp message is displayed.
Brightness Mode
Bright: Choose “Bright” to increase the brightness.
Dynamic: Choose “Dynamic“ to dim the lamp power which will be based
on brightness level of the content and adjust lamp power consumption
between 100% and 30% dynamically. The lamp life will be extended.
Eco+: Choose “Eco+” to dim the lamp power which will be based on
brightness level of the content and adjust lamp power consumption
between 80% and 30% dynamically. The lamp life will be extended.
Lamp Reset
Reset the lamp hour counter after replacing the lamp.
Optional Filter Settings
Optional Filter Installed
Choose “Yes” if an optional dust filter is installed.
Filter Usage Hours
Display the dust filters elapsed operating time (in hours).
EN-49
Filter Reminder
Sets a filter reminder if timer is up.
Filter Reset
Reset the dust filter hour counter after replacing the dust filter.
Reset
Choose “Yes” to return the display parameters on all menus to the factory
default settings.
EN-50
Controlling the projector through a
LAN environment
You can manage and control the projector from one or more remote comput-
ers when they are properly connected to the same local area network.
Wired connection
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of
the projector and the other end to the RJ45 port on your Ethernet or
router.
2. Press “Menu” and then go to SETUP > Network menu.
3. Highlight LAN Settings and press “Enter”.
4. Make sure the Network Status shows Connected.
5. Press to highlight DHCP and press / to select On.
6. Please wait for around 15 - 20 seconds, and then re-enter the Wired
LAN page. The IP Address, Subnet Mask, Gateway, and DNS settings
will be displayed. Note down the IP address displayed in the IP Address
row.
Important
If the Projector IP Address still does not appear, contact your network administrator.
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Gateway, and DNS information when
the projector is on.
If you are in a non-DHCP environment:
1. Repeat steps 1-4 above.
2. Press
to highlight DHCP and press / to select Off.
3. Contact your ITS administrator for information on the IP Address, Subnet
Mask, Gateway, and DNS settings.
4. Press
to select the item you want to modify and press “Enter”.
Internet
IP Router
EN-51
5. Press / to move the cursor and enter the value.
6. When you press “Menu”, a confirm message will pop-up to ask you if you
want to save the settings.
Important
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Gateway, and DNS information when
the projector is on.
EN-52
Wireless connection
To connect to the projector wirelessly, you have to plug an Optoma wireless
dongle (optional) to the USB Type A connector on the side of the projector,
and then only a few OSD configuration steps are required.
1. Make sure the projector is turned on.
2. Press “Menu” and then go to SETUP > Network menu.
3. Highlight WLAN and press “Enter”.
4. Make sure the Network Status shows Connected.
5. Make sure the SSID information is displayed.
6. In AP mode, you need to use your computer’s wireless connection utility
to search the projectors SSID and connect to it. Then you can search
the projector with Optoma Presenter. To use Infrastructure mode, you
should connect both your computer and projector to the same AP router
and make connections with the IP address.
Optoma wireless dongle
EN-53
About AP and Infrastructure modes
In AP mode, you need to use your computer's wireless connection utility to
search for the projector's SSID and connect to it. Then you can search for
the projector with Optoma Presenter.
In Infrastructure mode, you should connect both your computer and projector
to the same AP router and make connections with the IP address.
The following diagram describes how to access the Internet in AP and Infra-
structure modes.
Important
If you need more information about AP and Infrastructure modes, please refer to user
documentations for Wireless Routers which are usually available on 3C stores.
(AP Mode)
Internet
(Infrastructure Mode)
Internet
EN-54
Controlling the projector through a web
browser
Once you have the correct IP address for the projector and the projector is
on or in standby mode, you can use any computer that is on the same local
area network to control the projector.
Important
Make sure your browser supports IE7, IE8, IE9, Saferi 5.1.2, Google Chrome 18,
Firefox 10.0.1.
The screenshots in this manual are for reference only, and may differ from the actual
design.
1. Enter the address of the projector in the address bar of your browser and
press Enter.
2. The main page of the Optoma webpage control system appears.
3. To change the language for the web pages, click the down arrow to
reveal a drop down list and select a desired language.
4. To download Optoma Presenter, click Download. See "Displaying
images through vsPresenter" on page 40 for details.
5. The Crestron (eControl) page displays the Crestron eControl user
interface. See “About Crestron control” on page 56 for details.
4
5
3
6
EN-55
6. To have access to the Admin page, you need to enter a password. The
default password is “admin”.
System Status: Displays the system information.
General Setup: Allows you to turn on/off the projector, switch the
input signal for the projector, and change the password for the
Administrator page.
Projector Control: Provides some OSD menu items for adjusting the
projected pictures. See "Menu Operation" on page 23 for details.
Alert Setup: Allows you to setup the mail server and send system
error messages to your ITS administrator.
Network Setup: Provides wired and wireless network settings.
Reset to Default: Allows you to restore the device to the factory
default settings.
Reboot System: Allows you to restart the network.
EN-56
About Crestron control
1. The Crestron (eControl) page displays the Crestron eControl user
interface. The eControl page provides a variety of virtual keys to control
the projector or adjust the projected pictures.
i. These buttons function the same as the ones on the OSD menus or
remote control.
ii. To switch between input signals, click on your desired signal.
Important
The Menu button can also be used to go back to previous OSD menus, exit and save
menu settings.
The source list varies according to the connectors available on the projector.
When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with
the projector.
You can press
W
/
X
to reveal
more buttons.
i
i
ii
i
EN-57
2. The tools page allows you to manage the projector, configure the LAN
control settings and secure access of remote network operation on this
projector.
i. This section is only used with the Crestron Control System. Please
contact Creston or refer to its user manual for setup information.
ii. This area is used for naming the projector, associating it with a par-
ticular location, assigning a responsible party to it, and adjusting net-
work settings.
iii. This area is used to set User and Admin passwords. When pass-
word protection is enabled, unauthorized changes to the projector
configuration will be avoided.
Important
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for
the projector.
iv. Press Exit to go back to the remote network operation page.
ii
v
iv
i
iii
EN-58
Please pay attention to the limitation of input length (including space and
other punctuation keys) in the list blow:
Category Item Input Length Maximum Number of
Characters
Crestron Control IP Address 15
IP ID 2
Port 5
Projector Projector Name 10
Location 9
Assigned To 9
Network Configuration DHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password Enabled (N/A)
New Password 20
Confirm 2
Admin Password Enabled (N/A)
New Password 20
Confirm 20
EN-59
3. The info page displays the information and status of this projector.
Press exit to go back to the Crestron remote network operation page.
4. After pressing the button “Contact IT Help”, the HELP DESK window will
appear in the upper right corner of the screen. You will be able to deliver
messages to RoomView software administrators/users who connect to
the same local area network.
Important
Please only deliver the messages in English letters and digits.
For more information, visit http://www.crestron.com & www.crestron.com/get-
roomview.
EN-60
**Crestron RoomView
On the "Edit Room" page, enter the IP Address (or hostname) as shown on
the projector's on-screen display (OSD) menu, and "05" for IPID, "41794" for
the reserved Crestron control port.
About Crestron RoomView setting and command method, please access
below website to get RoomView User Guide and more information:
http://www.crestron.com/features/
roomview_connected_embedded_projectors_devices/resources.asp
EN-61
Displaying images through Optoma
Presenter
Downloading and installing Optoma Presenter
The Optoma Presenter is an application running on the host PC. It helps
connect your computer to an available network projector and transfer the
desktop content to the network projector via local network connection.
1. Enter the main page of Network Control. See steps 1-2 on page 54 for
details.
2. Download Optoma Presenter.
3. When the download is complete, install the software to your computer by
clicking the exe file. Follow the on-screen instructions to complete the
installation.
4. Launch Optoma Presenter.
Using Optoma Presenter
1. The Search page allows you to search and connect to a projector.
1
2
4
3
EN-62
i. To search for projectors, simply click Search to list all the projectors
on the same local area network. Click the desired projectors in the
Search result list, and click Connect. You can also type a desired
projector name and click Search.
ii. You can also type the projector IP address and click Connect to con-
nect the projector directly.
2. You can choose a capture mode and display location from here.
i. To display a full screen, click FullScreen.
ii. If you wish to change the square, click Alterable.
iii. If there are multiple computers connected to the projector, you can
decide a display zone by clicking All, L, R, 1, 2, 3 or 4.
3. You can manage the connected projectors listed under Device
Management.
Under a conference mode:
1. Only the administrator can take control.
2. A projector can display up to 4 computer screens.
EN-63
You can set the name of your computer under Optoma Presenter
Management.
For details about the icons, please see the following:
4. The Setting page allows you to configure Optoma Presenter.
i. To change the Optoma Presenter interface language, click the down
arrow to reveal a drop-down list and select a desired language. Click
Apply.
Icon Description Icon Description
You are a normal user and
have no access to change
the password.
Disconnects from the pro-
jector.
You are an administrator
and have authority to
change the password.
Opens the web page of
the Network Control.
You are the user of the
projector.
There is another user of
the projector.
You are an administrator
of the projector.
You are a normal user of
the projector.
Sets a display zone for the projector.
EN-64
ii. To allow notification messages to appear, click Yes. Click Apply.
iii. To adjust the image quality, click the down arrow to reveal a drop-
down list and select a desired quality level. The higher image quality
you select, the higher network transfer speed is required. Click Apply
after your selections.
iv. To enable audio out, click Yes. Click Apply.
v. The Software Information is available on this page.
EN-65
Displaying pictures with a USB storage
device
The projector is built-in an application which can display packaged images
on a USB storage device. It can eliminate the need for a computer source.
The projector supports the following image formats:
Progressive JPEG files are not supported.
Some JPEG files may not be displayed clearly.
To display the images on a USB storage device:
1. Plug the USB storage device into the FLASH DRIVE socket.
2. The projector automatically displays the main screen. Or your can
manually select Flash drive from the source selection bar.
3. Press “Enter” to display the content of your USB storage device.
4. When only one USB is plugged, folders and supported files are
represented in thumbnail mode.
To scroll through the thumbnails, use the four directional arrow keys.
To open a folder/file, press “Enter”.
File format Maximum pixel size
JPEG 8000 x 8000
GIF/TIFF/PNG/BMP 1280 x 800
Icon Description
Go to the top level of the selected USB
Go to previous level of folder
Setup function
EN-66
Setup function
Use the four directional arrow keys to highlight options.
Press “Enter” to switch the settings of the highlighted function.
Go back to thumbnail file, press .
Select another USB
Thumbnail Order Description
File order by time
Sort by recent update to past
File order by characters
It is sorted by first character of file name.
Folder (0-9,a-z,symbols)
Files (0-9,a-z,symbols)
Slidesow Description
Sets the time interval each image displays.
Sets the way the slide show is displayed.
Sets whether to repeat the slide shows.
EN-67
5. When more than one USB is plugged, press “Enter” to switch to another
USB.
Slide shows
1. When user press "Enter" into a picture, it will display picture auto fit to
the screen by retaining original size ratio.
2. Press "Enter" key to shows setting bar.
When it’s on slideshow
:
Icon Description
Keep slideshow
Stop slideshow and only display this picture
Go back to thumbnail file
Press button Action
EN-68
When it's only displaying one picture:
Right Jump to next photo and keep slideshow
Left Jump to previous photo and keep slideshow
Enter Show setting bar
Menu Show projector menu
Press button Action
Up
Rotate +90
°
Down
Rotate -90
°
Right Jump to next photo
Left Jump to previous photo
Enter Show setting bar
Menu Show projector menu
EN-69
Appendix
Replacing the Dust Filter
Be sure to follow the steps to replace the dust filter.
The dust filter should be cleaned or replaced periodically (suggest
after every 500 hours or 3 months of use). If it is not cleaned
periodically, it can become clogged with dust and prevent the
projector from being ventilated properly. This can cause over
heating and damage the projector. If the projector is used in a dusty
environment, be sure to cleaned or replaced the dust filter more
frequently.
1. Remove the dust filter, located at the rear side of the projector, by pulling
it out as the illustration.
2. Clean the dust filter .
To clean the dust filter, you are advised to use a small vacuum
cleaner designed for computers and other office equipment.
If the dust filter is torn, replace it.
3. Turn on the projector, then press “Menu”, go to
OPTIONS > Optional Filter > Optional Filter Installed and
select “Yes”.
4. Turn on the projector, then press “Menu”, go to OPTIONS > Optional
Filter > Optional Filter Installed and select “No” when you pull out the
dust filter and would not use it again.
dust filter
EN-70
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp
gradually decreases and the lamp becomes more susceptible to breakage.
We recommend replacing the lamp if a warning message is displayed. Do
not attempt to replace the lamp yourself. Contact the qualified service
personnel for replacement.
Note
The lamp is extremely hot right after turning off the projector. If you touch the lamp,
you may scald your finger. When you replace the lamp, wait for at least 45 minutes for
the lamp to cool down.
Do not touch the lamp glass at any time. The lamp may explode due to improper
handling, including the touching of the lamp glass.
Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or
terminate their lifetime in a shorter period of time than other similar lamps.
A lamp may explode as a result of vibration, shock or degradation as a result of hours
of use as its lifetime draws to an end. Risk of explosion may differ according to the
environment or conditions in which the projector and lamp are being used.
Wear protective gloves and eyeglasses when fixing or detaching the lamp.
Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
Do not operate the lamp in proximity to paper, cloth, or other combustible material
nor cover it with such materials.
Do not operate the lamp in an atmosphere containing an inflammable substance,
such as thinner.
Thoroughly ventilate the area or the room when operating the lamp in an oxygen
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea,
dizziness, and other symptoms.
The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside
the lamp will be exposed. Leave the area immediately if the lamp shatters while being
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation
of mercury fumes. Otherwise it could be harmful to users health.
EN-71
1. Turn off the projector.
2. Unplug the power cord.
3. Open the top cover, by sliding the top cover forward, and lifting the top
cover off.1
4. Remove the screw on the lamp cover and then open it up. 2 & 3
5. Loosen the screws from the lamp module. 4
6. Raise the handle and pull out the lamp module slowly and carefully. 5
7. Insert the new lamp module into the projector and tighten the screws.
8. Replace the lamp cover and tighten the screw.
9. Replace the top cover by (a) aligning the cover (b) sliding it toward the
back and (c) locking it back into place.
10. Turn on the projector. If the lamp does not turn on after the warm-up
period, try reinstalling the lamp.
11. Reset the lamp hour. Refer to the “OPTIONS > Lamp Settings” menu.
Note
Dispose the used lamp according to local regulations.
Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
Do not reuse the old lamp. This could cause the lamp to explode.
Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
Do not use the projector with the lamp cover removed.
EN-72
Ceiling mount installation
1. To prevent damage to your projector, please use the Optoma ceiling
mount.
2. If you wish to use a third party ceiling mount kit, please ensure the
screws used to attach a mount to the projector meet the following
specifications:
Screw type: M4*3
Maximum screw length: 10mm
Minimum screw length: 8mm
Note
Please note that damage resulting from incorrect installation will void the warranty.
Warning
1.If you buy a ceiling mount from another company, please be sure
to use the correct screw size. Screw length will vary depending on
the thickness of the mounting plate.
2.Be sure to keep at least 10 cm gap between the ceiling and the
bottom of the projector.
3.Avoid installing the projector near a heat source.
55
82.3
55
110
Unit: mm
Lens
65.04
80.89
EN-73
Compatibility Modes
Computer Compatibility
(*)1920 x 1200 @60hz only support reduced blanking
(**) 3D timing for True 3D projector
Signal Resolution Refresh Rate(Hz) Notes for Mac
VGA 640 X 480 60/67/72/85 Mac 60/72/85
SVGA 800 X 600 60(**)/72/85/120(**) Mac 60/72/85
XGA 1024 X768 60(**)/70/75/85/
120(**)
Mac 60/70/75/85
HDTV(720P) 1280 X 720 50/60(**)/120(**) Mac 60
WXGA 1280 X768 60/75/85 Mac 60/75/85
1280 X800 60(**)/120(**) Mac 60
1366 X 768 60 Mac 60
WXGA+ 1440 X 900 60 Mac 60
SXGA 1280 X1024 60 Mac 60/75
SXGA+ 1400 X1050 60
UXGA 1600 X 1200 60
HDTV(1080p) 1920 X1080 60 Mac 60
WUXGA 1920 X1200(*) 60 Mac 60
EN-74
Input Signal for HDMI
(*)1920 x 1200 @60hz only support reduced blanking
(**)3D timing for True 3D projector
Signal Resolution Refresh Rate(Hz) Notes for Mac
VGA 640 X 480 60 Mac 60/72/85
SVGA 800 X 600 60(**)/72/85/120(**) Mac 60/72/85
XGA 1024 X 768 60(**)/70/75/85/
120(**)
Mac 60/70/75/85
SDTV(480I) 640 X 480 60
SDTV(480P) 640 X 480 60
SDTV(576I) 720 X 576 50
SDTV(576P) 720 X 576 50
WSVGA(1024X600) 1024 X 600 60
HDTV(720p) 1280 X 720 50(**)/60/120(**) Mac 60
WXGA 1280 X768 60/75/85 Mac 75
1280 X800 60(**)/120(**) Mac 60
1366 x 768 60 Mac 60
WXGA+ 1440 x 900 60 Mac 60
SXGA 1280 X1024 60/75/85 Mac 60/75
SXGA+ 1400 X1050 60
UXGA 1600 X 1200 60
HDTV(1080I) 1920 X1080 50/60
HDTV(1080p) 1920 X1080 24/30/50/60 Mac 60
WUXGA 1920 X1200(*) 60 Mac 60
EN-75
True 3D Video Compatibility table
If 3D input is 1080p@24hz, the DMD should replay with integral multiple with 3D
mode
Support NVIDIA 3DTV Play if there is no patent fee from Optoma
1080i@25hz and 720p@50hz will run in 100hz; other 3D timing will run in 120hz.
1080P@24hz will run 144Hz.
Video Compatibility
Input Resolutions
HDMI 1.4a
3D Input
Input timing
1280 X 720P @ 50Hz Top - and - Bottom
1280 X 720P @ 60Hz Top - and - Bottom
1280 X 720P @ 50Hz Frame packing
1280 X 720P @ 60Hz Frame packing
1920 X 1080i @50 Hz Side- by-Side (Half)
1920 X 1080i @60 Hz Side- by-Side (Half)
1920 X 1080P @24 Hz Top - and - Bottom
1920 X 1080P @24 Hz Frame packing
HDMI 1.3
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
1280 x 720P @ 50Hz
1280 x 720P @60Hz
Side-by-
Side(Half)
SBS mode
is on
1920 x 1080i @ 50Hz
1920 x1080i @ 60Hz
1280 x 720P @ 50Hz
1280 x 720P @60Hz
Top-and-
Bottom
TAB mode is
on
480i HQFS 3D format is
Frame
sequential
NTSC NTSC M/J, 3.58MHz, 4.43MHz
PAL PAL B/D/G/H/I/M/N, 4.43MHz
SECAM SECAM B/D/G/K/K1/L, 4.25/4.4 MHz
Component 480i/p, 576i/p, 720p(50/60Hz), 1080i(50/60Hz)
1080P(24/50/60Hz)
SDTV 480i/p, 576i/p
HDTV 720p(50/60Hz), 1080i(50/60Hz), 1080P(50/60Hz)
EN-76
IR Code
Customer code: 32CD
Key code Printing-key definition
81 Power on/off
3E Switch
C3 Source
97 User
C4 Re-Sync
CB L
CC R
C6 Up arrow
C8 Left arrow
C9 Right arrow
EN-77
The IR codes below are for user-defined remote only.
C7 Down arrow
C5 Enter
CA Enter
N/A Laser
C1 Page+
95 Mode
C2 Page-
85 Keystone+
84 Keystone-
8C Volume +
8F Volume -
87 Brightness/1
88 Menu/2
89 Zoom/3
86 HDMI/4
8B Freeze/5
8A AV mute/6
83 S-Video/7
8E VGA/8
8D Video/9
96 Eco
+
93 3D
79 Power off (single push)
82 Power off
80 Power on
9A VGA2
99 Network Display
9E DVI
94 Contrast
EN-78
Telnet Commands
Port: support port 23
Multi-connections: Projector could receive commands from different
ports at the same time
Command Format: Follow RS232 command format (support both of
ASCII and HEX)
Command Response: Follow RS232 return message.
Note
Note: When the data length is greater or shorter than indicated by the data length
code, the projector returns the error code to computer.
Lead Code Projector ID Command ID space variable
carriage
return
~ X X XXX n CR
Fix code
One Digit
00
Defined by Optoma
2 or 3 Digit
See the Follow content
One Digit
Per item
Definition
Fix code
One digit
EN-79
PJLink commands
Support PJ link: click on below documents (English only)
Name? Projector name Varies with the different products.
INF0? Resolution
The native resolution of projector and it varies
with the different products.
Format:SVGA,XGA,WXGA,1080p, WUXGA
INF1? Optoma
INF2? Model name Varies with the different products.
RGB1 VGA1
RGB2 VGA2
VIDEO1 Video
VIDEO2 S-Video
DIGITAL1 HDMI
DIGITAL2 DVI
STORAGE1 Flash Drive
STORAGE2 USB Display
NETWORK1 Network Display
EN-80
AMX Device Discovery commands
UDP : 239.255.250.250
Port No. : 9131
Each UDP broadcast information as below are updated around 40 seconds
Attention
1. This AMX function is only to support AMX Device Discovery.
2. The broadcast information only send out through valid interface.
3. Both LAN and Wireless LAN interfaces could be supported at the same
time.
4. If "Beacon Validator" was used. Please take care below information.
Command Description Value
Device-UUID
MAC address(Hex value without ‘:’
separator)
12 digits
Device-
SDKClass
The Duet DeviceSdk class name VideoProjector
Device-Make Maker name MakerPXLW
Device-Model Model name Projector
Config-URL
Device’s IP address
LAN IP address is shown up if LAN IP
address is valid.
Wireless LAN IP address is shown up if
Wireless LAN IP address is valid.
http://xxx.xxx.xxx.xxx/index.html
Revision
The revision must follow a
major.minor.micro scheme.
The revision is only increased if the
command protocol is modified.
1.0.0
EN-81
RS232 Commands and Protocol
Function List
RS232 Pin Assignments
D-Sub 9 pin
(from the projector side)
11 CD
2RXD
3TXD
4DTR
5GND
6DSR
7RTS
8CTS
9RI
(from the cable side)
C1 COLOR C2
1Black1
2Brown3
3Red2
4 Orange 6
5Yellow5
6Green4
7Blue8
8 Purple 7
9White9
SHELL DW SHELL
EN-82
RS232 Protocol Function List
Note
To also include AMX beacon signal in RS232 protocol
In basic terms, AMX controllers will issue a poll periodically to detect 3rd party
devices connected to the RS232 port (in this case Optoma). The poll is "AMX" in ASCII
followed by a carriage return 'r'.
There is a <CR> after all ASCII commands.
0D is the HEX code for <CR> in ASCII code
Baud Rate 9600
Data Bits 8
Parity None
Stop Bits 1
Flow Control None
UART16550 FIFO Disable
Projector Return (Pass) P
Projector Return (Fail) F
Lead Code Projector ID Command ID space variable
carriage
return
~ X X XXX n CR
Fix code
One Digit
Set in OSD
00~99
Two Digit
Defined by Optoma
2 or 3 Digit
See the Follow content
One Digit
Per item
Definition
Fix code
One digit
EN-83
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
SEND to projector
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 ASCII Code HEX Code Function Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX00 1 7E 30 30 30 30 20 31 0D Power ON
~XX00 0 7E 30 30 30 30 20 30 0D Power OFF (0/2 for backward compatible)
~XX00 1 ~nnnn 7E 30 30 30 30 20 31 20 a 0DPower ON with Password ~nnnn = ~0000 (a=7E 30 30 30 30)
~9999 (a=7E 39 39 39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX01 1 7E 30 30 30 31 20 31 0D Resync
~XX02 1 7E 30 30 30 32 20 31 0D AV Mute On
~XX02 0 7E 30 30 30 32 20 30 0D Off (0/2 for backward compatible)
~XX03 1 7E 30 30 30 33 20 31 0D Mute On
~XX03 0 7E 30 30 30 33 20 30 0D Off (0/2 for backward compatible)
~XX04 1 7E 30 30 30 34 20 31 0D Freeze
~XX04 0 7E 30 30 30 34 20 30 0D Unfreeze (0/2 for backward compatible)
~XX05 1 7E 30 30 30 35 20 31 0D Zoom Plus
~XX06 1 7E 30 30 30 36 20 31 0D Zoom Minus
~XX12 1 7E 30 30 31 32 20 31 0D Direct Source Commands HDMI
~XX12 3 7E 30 30 31 32 20 33 0D DVI-I
~XX12 5 7E 30 30 31 32 20 35 0D VGA1
~XX12 6 7E 30 30 31 32 20 36 0D VGA 2
~XX12 8 7E 30 30 31 32 20 38 0D VGA1 Component
~XX12 9 7E 30 30 31 32 20 39 0D S-Video
~XX12 10 7E 30 30 31 32 20 31 30 0D Video
~XX12 13 7E 30 30 31 32 20 31 33 0D VGA 2 Component
~XX12 17 7E 30 30 31 32 20 31 37 0D Flash drive
~XX12 18 7E 30 30 31 32 20 31 38 0D Network Display
~XX12 19 7E 30 30 31 32 20 31 39 0D USB display
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX20 1 7E 30 30 32 30 20 31 0D Display Mode Presentation
~XX20 2 7E 30 30 32 30 20 32 0D Bright
~XX20 3 7E 30 30 32 30 20 33 0D Movie
~XX20 4 7E 30 30 32 30 20 34 0D sRGB
~XX20 5 7E 30 30 32 30 20 35 0D User
~XX20 7 7E 30 30 32 30 20 37 0D Blackboard
~XX20 13 7E 30 30 32 30 21 33 0D DICOM SIM.
~XX20 9 7E 30 30 32 30 20 39 0D 3D
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX21 n 7E 30 30 32 31 20 a 0D Brightness n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX22 n 7E 30 30 32 32 20 a 0D Contrast n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX23 n 7E 30 30 32 33 20 a 0D Sharpness n = 1 (a=31) ~ 15 (a=31 35)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- -----------------------------
~XX24 n 7E 30 30 32 34 20 a 0D Color Settings/White Red n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX25 n 7E 30 30 32 35 20 a 0D Green n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX26 n 7E 30 30 32 36 20 a 0D Blue n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX33 1 7E 30 30 33 33 20 31 0D Reset
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX34 n 7E 30 30 33 34 20 a 0D BrilliantColor
TM
n = 1 (a=31) ~ 10 (a=31 30)
~XX35 1 7E 30 30 33 35 20 31 0D Gamma Film
~XX35 2 7E 30 30 33 35 20 32 0D Video
~XX35 3 7E 30 30 33 35 20 33 0D Graphics
~XX35 4 7E 30 30 33 35 20 34 0D 2.2
~XX35 5 7E 30 30 33 35 20 35 0D 1.8
~XX35 6 7E 30 30 33 35 20 36 0D 2.0
~XX35 7 7E 30 30 33 35 20 37 0D 2.6
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX36 1 7E 30 30 33 36 20 31 0D Color Temp. Warm
~XX36 2 7E 30 30 33 36 20 32 0D Medium
~XX36 3 7E 30 30 33 36 20 33 0D Cold
~XX37 1 7E 30 30 33 37 20 31 0D Color Space Auto
~XX37 2 7E 30 30 33 37 20 32 0D RGB\ RGB(0-255)
~XX37 3 7E 30 30 33 37 20 33 0D YUV
~XX37 4 7E 30 30 33 37 20 34 0D RGB(16 - 235)
~XX73 n 7E 30 30 37 33 20 a 0D Signal Frequency n = -5 (a=2D 35) ~ 5 (a=35) By signal
~XX91 1 7E 30 30 39 31 20 31 0D Automatic On
~XX91 0 7E 30 30 39 31 20 30 0D Off
~XX74 n 7E 30 30 37 34 20 a 0D Phase n = 0 (a=30) ~ 31 (a=33 31) By signal
~XX75 n 7E 30 30 37 35 20 a 0D H. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX76 n 7E 30 30 37 36 20 a 0D V. Position n = -5 (a=2D 35) ~ 5 (a=35) By timing
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX45 n 7E 30 30 34 34 20 a 0D Color (Saturation) n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX44 n 7E 30 30 34 35 20 a 0D Tint n = -50 (a=2D 35 30) ~ 50 (a=35 30))
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX60 1 7E 30 30 36 30 20 31 0D Format 4:3
~XX60 2 7E 30 30 36 30 20 32 0D 16:9
~XX60 3 7E 30 30 36 30 20 33 0D 16:10(W501)
~XX60 5 7E 30 30 36 30 20 35 0D LBX
~XX60 6 7E 30 30 36 30 20 36 0D Native
~XX60 7 7E 30 30 36 30 20 37 0D Auto
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX61 n 7E 30 30 36 31 20 a 0D Edge mask n = 0 (a=30) ~ 10 (a=31 30)
~XX62 n 7E 30 30 36 32 20 a 0D Zoom n = -5 (a=2D 35) ~ 25 (a=32 35)
~XX63 n 7E 30 30 36 33 20 a 0D H Image Shift n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30)
~XX64 n 7E 30 30 36 34 20 a 0D V Image Shift n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30)
~XX66 n 7E 30 30 36 36 20 a 0D V Keystone n = -40 (a=2D 34 30) ~ 40 (a=34 30)
~XX69 1 7E 30 30 36 39 20 31 0D Auto Keystone On
~XX69 0 7E 30 30 36 39 20 30 0D Auto Keystone Off
~XX230 1 7E 30 30 32 33 30 20 31 0D 3D Mode DLP-Link
EN-84
~XX230 3 7E 30 30 32 33 30 20 31 0D 3D Mode IR
~XX400 0 7E 30 30 34 30 30 20 30 0D 3DШ2D 3D
~XX400 1 7E 30 30 34 30 30 20 31 0D L
~XX400 2 7E 30 30 34 30 30 20 32 0D R
~XX405 0 7E 30 30 34 30 35 20 30 0D 3D Format Auto
~XX405 1 7E 30 30 34 30 35 20 31 0D SBS
~XX405 2 7E 30 30 34 30 35 20 32 0D Top and Bottom
~XX405 3 7E 30 30 34 30 35 20 33 0D Frame sequential
~XX231 0 7E 30 30 32 33 31 20 30 0D 3D Sync Invert On
~XX231 1 7E 30 30 32 33 31 20 31 0D 3D Sync Invert Off
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX70 1 7E 30 30 37 30 20 31 0D Language English
~XX70 2 7E 30 30 37 30 20 32 0D German
~XX70 3 7E 30 30 37 30 20 33 0D French
~XX70 4 7E 30 30 37 30 20 34 0D Italian
~XX70 5 7E 30 30 37 30 20 35 0D Spanish
~XX70 6 7E 30 30 37 30 20 36 0D Portuguese
~XX70 7 7E 30 30 37 30 20 37 0D Polish
~XX70 8 7E 30 30 37 30 20 38 0D Dutch
~XX70 9 7E 30 30 37 30 20 39 0D Swedish
~XX70 10 7E 30 30 37 30 20 31 30 0D Norwegian/Danish
~XX70 11 7E 30 30 37 30 20 31 31 0D Finnish
~XX70 12 7E 30 30 37 30 20 31 32 0D Greek
~XX70 13 7E 30 30 37 30 20 31 33 0D Traditional Chinese
~XX70 14 7E 30 30 37 30 20 31 34 0D Simplified Chinese
~XX70 15 7E 30 30 37 30 20 31 35 0D Japanese
~XX70 16 7E 30 30 37 30 20 31 36 0D Korean
~XX70 17 7E 30 30 37 30 20 31 37 0D Russian
~XX70 18 7E 30 30 37 30 20 31 38 0D Hungarian
~XX70 19 7E 30 30 37 30 20 31 39 0D Czechoslovak
~XX70 20 7E 30 30 37 30 20 32 30 0D Arabic
~XX70 21 7E 30 30 37 30 20 32 31 0D Thai
~XX70 22 7E 30 30 37 30 20 32 32 0D Turkish
~XX70 23 7E 30 30 37 30 20 32 33 0D Farsi
~XX70 25 7E 30 30 37 30 20 32 33 0D Vietnamese
~XX70 26 7E 30 30 37 30 20 32 33 0D Indonesian
~XX70 27 7E 30 30 37 30 20 32 33 0D Romanian
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX71 1 7E 30 30 37 31 20 31 0D Projection Front-Desktop
~XX71 2 7E 30 30 37 31 20 32 0D Rear-Desktop
~XX71 3 7E 30 30 37 31 20 33 0D Front-Ceiling
~XX71 4 7E 30 30 37 31 20 34 0D Rear-Ceiling
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX72 1 7E 30 30 37 32 20 31 0D Menu Location Top Left
~XX72 2 7E 30 30 37 32 20 32 0D Top Right
~XX72 3 7E 30 30 37 32 20 33 0D Centre
~XX72 4 7E 30 30 37 32 20 34 0D Bottom Left
~XX72 5 7E 30 30 37 32 20 35 0D Bottom Right
(EW501 only)
~XX90 1 7E 30 30 39 31 20 31 0D Screen Type 16:10
~XX90 0 7E 30 30 39 31 20 30 0D 16:9
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX77 n 7E 30 30 37 37 20 aabbcc 0D Security Security Timer Month/Day/Hour n = mm/dd/hhmm= 00 (aa=30 30) ~ 12
(aa=31 32)
dd = 00 (bb=30 30) ~ 30 (bb=33 30)
hh= 00 (cc=30 30) ~ 24 (cc=32 34)
~XX78 1 7E 30 30 37 38 20 31 0D Security Settings Enable
~XX78 0 ~nnnn 7E 30 30 37 38 20 32 20 a 0D Disable(0/2 for backward compatible) ~nnnn = ~0000
(a=7E 30 30 30 30)
~9999 (a=7E 39 39 39 39)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX79 n 7E 30 30 37 39 20 a 0D Projector ID n = 00 (a=30 30) ~ 99 (a=39 39)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX80 1 7E 30 30 38 30 20 31 0D Mute On
~XX80 0 7E 30 30 38 30 20 30 0D Off (0/2 for backward compatible)
~XX310 0 7E 30 33 31 30 20 30 0D Internal Speaker Off
~XX310 1 7E 30 33 31 30 20 31 0D On
~XX81 n 7E 30 30 38 31 20 a 0D Volume(Audio) n = 0 (a=30) ~ 10 (a=31 30)
~XX93 n 7E 30 30 39 33 20 a 0D Volume(Mic) n = 0 (a=30) ~ 10 (a=31 30)
~XX89 0 7E 30 30 38 39 20 30 0D Audio Input Default
~XX89 1 7E 30 30 38 39 20 31 0D Audio1
~XX89 3 7E 30 30 38 39 20 33 0D Audio2
~XX89 4 7E 30 30 38 39 20 34 0D Audio3
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX82 1 7E 30 30 38 32 20 31 0D Logo Default
~XX82 2 7E 30 30 38 32 20 32 0D User
~XX82 3 7E 30 30 38 32 20 33 0D Neutral
~XX83 1 7E 30 30 38 33 20 31 0D Logo Capture
~XX88 0 7E 30 30 38 38 20 30 0D Closed Captioning Off
~XX88 1 7E 30 30 38 38 20 31 0D cc1
~XX88 2 7E 30 30 38 38 20 32 0D cc2
~XX450 0 7E 30 30 34 35 30 20 30 0D WLAN Off
~XX450 1 7E 30 30 34 35 30 20 31 0D On
~XX454 0 7E 30 30 34 35 34 20 30 0D Crestron Off
~XX454 1 7E 30 30 34 35 34 20 31 0D On
EN-85
~XX455 0 7E 30 30 34 35 35 20 30 0D Extron Off
~XX455 1 7E 30 30 34 35 35 20 31 0D On
~XX456 0 7E 30 30 34 35 36 20 30 0D PJLink Off
~XX456 1 7E 30 30 34 35 36 20 31 0D On
~XX457 0 7E 30 30 34 35 37 20 30 0D AMX Device Discovery Off
~XX457 1 7E 30 30 34 35 37 20 31 0D On
~XX458 0 7E 30 30 34 35 38 20 30 0D Telnet Off
~XX458 1 7E 30 30 34 35 38 20 31 0D On
~XX459 0 7E 30 30 34 35 38 20 30 0D HTTP Off
~XX459 1 7E 30 30 34 35 38 20 31 0D On
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX100 1 7E 30 30 31 30 30 20 31 0D Source Lock On
~XX100 0 7E 30 30 31 30 30 20 30 0D Off (0/2 for backward compatible)
~XX101 1 7E 30 30 31 30 31 20 31 0D High Altitude On
~XX101 0 7E 30 30 31 30 31 20 30 0D Off (0/2 for backward compatible)
~XX102 1 7E 30 30 31 30 32 20 31 0D Information Hide On
~XX102 0 7E 30 30 31 30 32 20 30 0D Off (0/2 for backward compatible)
~XX103 1 7E 30 30 31 30 33 20 31 0D Keypad Lock On
~XX103 0 7E 30 30 31 30 33 20 30 0D Off (0/2 for backward compatible)
~XX195 0 7E 30 30 31 39 35 20 30 0D Test Pattern None
~XX195 1 7E 30 30 31 39 35 20 31 0D Grid
~XX195 2 7E 30 30 31 39 35 20 32 0D White Pattern
~XX192 0 7E 30 30 31 39 32 20 30 0D 12V Trigger Off
~XX192 1 7E 30 30 31 39 32 20 31 0D On
~XX192 3 7E 30 30 31 39 32 20 33 0D Auto 3D
~XX11 0 7E 30 30 31 31 20 30 0D IR Function Off
~XX11 1 7E 30 30 31 31 20 31 0D On
~XX11 2 7E 30 30 31 31 20 32 0D Front
~XX11 3 7E 30 30 31 31 20 33 0D Back
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX104 1 7E 30 30 31 30 34 20 31 0D Background Color Blue
~XX104 2 7E 30 30 31 30 34 20 32 0D Black
~XX104 3 7E 30 30 31 30 34 20 33 0D Red
~XX104 4 7E 30 30 31 30 34 20 34 0D Green
~XX104 5 7E 30 30 31 30 34 20 35 0D White
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX105 1 7E 30 30 31 30 35 20 31 0D Advanced Direct Power On On
~XX105 0 7E 30 30 31 30 35 20 30 0D Off (0/2 for backward compatible)
~XX113 0 7E 30 30 31 31 33 20 30 0D Signal Power On Off
~XX113 1 7E 30 30 31 31 33 20 31 0D On
~XX106 n 7E 30 30 31 30 36 20 a 0D Auto Power Off (min) n = 0 (a=30) ~ 180 (a=31 38
30)
(5 minutes for each step).
~XX107 n 7E 30 30 31 30 37 20 a 0D Sleep Timer (min) n = 0 (a=30) ~ 990 (a=39 39
30)
(30 minutes for each step).
~XX115 1 7E 30 30 31 31 35 20 31 0D Quick Resume On
~XX115 0 7E 30 30 31 31 35 20 30 0D Off (0/2 for backward
compatible)
~XX114 1 7E 30 30 31 31 34 20 31 0D Power Mode(Standby) Eco.(<=0.5W)
~XX114 0 7E 30 30 31 31 34 20 30 0D Active (0/2 for backward
compatible)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX109 1 7E 30 30 31 30 39 20 31 0D Lamp Reminder On
~XX109 0 7E 30 30 31 30 39 20 30 0D Off (0/2 for backward compatible)
~XX110 1 7E 30 30 31 31 30 20 31 0D Brightness Mode Bright
~XX110 3 7E 30 30 31 31 30 20 33 0D Eco
+
~XX110 4 7E 30 30 31 31 30 20 34 0D Dynamic
~XX111 1 7E 30 30 31 31 31 20 31 0D Lamp Reset Yes
~XX111 0 7E 30 30 31 31 31 20 30 0D No (0/2 for backward compatible)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX320 1 7E 30 30 33 32 30 20 31 0D Optional Filter Installed Yes
~XX320 0 7E 30 30 33 32 30 20 30 0D No (0/2 for backward
compatible)
~XX322 0 7E 30 30 33 32 32 20 30 0D Filter Reminder Off
~XX322 1 7E 30 30 33 32 32 20 31 0D 300 hr
~XX322 2 7E 30 30 33 32 32 20 32 0D 500 hr
~XX322 3 7E 30 30 33 32 32 20 33 0D 800 hr
~XX322 4 7E 30 30 33 32 32 20 34 0D 1000 hr
~XX323 1 7E 30 30 33 32 33 20 31 0D Filter Reset Yes
~XX323 0 7E 30 30 33 32 33 20 30 0D No(0/2 for backward
compatible)
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX112 1 7E 30 30 31 31 32 20 31 0D Reset Yes
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
~XX99 1 7E 30 30 39 39 20 31 0D RS232 Alert Reset Reset System Alert
~XX210 n 7E 30 30 32 30 30 20 n 0D Display message on the OSD n: 1-30 characters
--------------------------------------------------------------------------------------------------------------------------------------------
SEND to emulate Remote
~XX140 10 7E 30 30 31 34 30 20 31 30 0D Up
~XX140 11 7E 30 30 31 34 30 20 31 31 0D Left
~XX140 12 7E 30 30 31 34 30 20 31 32 0D Enter (for projection MENU)
~XX140 13 7E 30 30 31 34 30 20 31 33 0D Right
~XX140 14 7E 30 30 31 34 30 20 31 34 0D Down
~XX140 15 7E 30 30 31 34 30 20 31 35 0D Keystone +
~XX140 16 7E 30 30 31 34 30 20 31 36 0D Keystone –
~XX140 17 7E 30 30 31 34 30 20 31 37 0D Volume –
EN-86
~XX140 18 7E 30 30 31 34 30 20 31 38 0D Volume +
~XX140 19 7E 30 30 31 34 30 20 31 39 0D Brightness
~XX140 20 7E 30 30 31 34 30 20 32 30 0D Menu
~XX140 21 7E 30 30 31 34 30 20 32 31 0D Zoom
~XX140 47 7E 30 30 31 34 30 20 34 37 0D Source
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
SEND from projector automatically
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 ASCII Code HEX Code Function Projector Return Description
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
when Standby/Warming/Cooling/Out of
Range/Lamp fail/Fan Lock/Over Temperature/
Lamp Hours Running Out/Cover Open
INFOn n : 0/1/2/3/4/6/7/8/ = Standby/Warming/Cooling/Out of
Range/Lamp fail/Fan Lock/Over Temperature/Lamp Hours
Running Out/Cover Open
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
READ from projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
232 ASCII Code HEX Code Function Projector Return Description
~XX121 1 7E 30 30 31 32 31 20 31 0D Input Source Commands OKn n: 0/1/2/3/4/5/6/7/8/9 =
None/VGA1/VGA2/Video/S-Video/HDMI/DVI/Flash
drive/Network display/USB display
~XX122 1 7E 30 30 31 32 32 20 31 0D Sofware Version OKdddd dddd: FW version
~XX123 1 7E 30 30 31 32 33 20 31 0D Display Mode OKn n : 0/1/2/3/4/5/6/7/8/
None/Presentation/Bright/Movie/sRGB/User/Blackboard/DICOM SIM./3D
~XX124 1 7E 30 30 31 32 34 20 31 0D Power State OKn n : 0/1 = Off/On
~XX125 1 7E 30 30 31 32 35 20 31 0D Brightness OKn
~XX126 1 7E 30 30 31 32 36 20 31 0D Contrast OKn
~XX127 1 7E 30 30 31 32 37 20 31 0D Format Okn (W501) n: 0/1/2/3/4/5 =
4:3/16:9/16:10/LBX/Native/AUTO
(EH501) n: 0/1/2/3/4 =4:3/16:9/LBX/Native/AUTO
(X501) n: 0/1/2/3 =4:3/16:9/Native/AUTO
*16:9 or 16:10 depend on Screen Type setting
~XX128 1 7E 30 30 31 32 38 20 31 0D Color Temperature OKn n : 0/1/2 = Warm/Medium/Cold
~XX129 1 7E 30 30 31 32 39 20 31 0D Projection Mode OKn n : 0/1/2/3 = Front-Desktop/ Rear-Desktop/ Front-Ceiling/
Rear-Ceiling
~XX150 1 7E 30 30 31 35 30 20 31 0D Information OKabbbbccdddde
a : 0/1 = Off/On
bbbb: LampHour
cc: source 00/01/02/03/04/05/06/07/08/09 =
None/VGA1/VGA2/Video/S-Video/HDMI/DVI/Flash Drive/Network display/USBdisplay
dddd: FW version
e : Display mode 0/1/2/3/4/5/6/7/8/
None/Presentation/Bright/Movie/sRGB/User/
Blackboard/ DICOM SIM /3D
~XX151 1 7E 30 30 31 35 31 20 31 0D Model name OKn n:1/2/3=X501/W501/EH501
~XX108 1 7E 30 30 31 30 38 20 31 0D Lamp Hours OKbbbb bbbb: LampHour
~XX108 2 7E 30 30 31 30 38 20 31 0D Cumulative Lamp Hours OKbbbbb bbbbb: (5 digits) Total Lamp
Hours
~XX321 1 7E 30 30 33 32 31 20 31 0D Filter Usage Hours OKbbbb bbbb: Filter Usage Hours
~XX87 1 7E 30 30 38 37 20 31 0D Network Status Okn n=0/1 Disconnected/Connected
~XX87 3 7E 30 30 38 37 20 33 0D IP Address Okaaa_bbb_ccc_ddd
~XX451 1 7E 30 30 34 35 31 20 31 0D WLAN Network Status Okn n=0/1 Disconnected/Connected
~XX451 2 7E 30 30 34 35 31 20 32 0D WLAN IP Address Okaaa_bbb_ccc_ddd
~XX451 3 7E 30 30 34 35 31 20 33 0D SSID Okaaaaaaaaaaaaaaaaaaaa
EN-87
Troubleshooting
Refer to the symptoms and measures listed below before sending the pro-
jector for repairs. If the problem persists, contact your local reseller or ser-
vice center. Please refer to "LED Indicator Messages" as well.
Start-up
If no lights turn on:
Be sure that the power cord is securely connected to the projector and the
other end
is plugged into an outlet with power.
Press the power button again.
Unplug the power cord and wait for a short while, then plug it in and press
the power
button again.
Image
If the searching source is displayed:
Press
SOURCE
on the projector or
Source
on the remote control
to select
an active input source.
Be sure the external source is turned on and connected.
For a computer connection, ensure your notebook computer’s external
video port is
turned on. Refer to the computer manual.
If the image is out of focus:
While displaying the on-screen menu, adjust the focus ring. (The image
size should
not change; if it does, you are adjusting the zoom, not the
focus.)
Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
Press
Menu
, go to IMAGE > Advanced > Signal and adjust Phase or
Frequency.
Remote control
If the remote control does not operate:
Be sure nothing is blocking the remote control receiver on the front of the
projector. Use the remote control within the effective range.
Aim the remote control at the screen or at the front of the projector.
Move the remote control so it is more directly in front of the projector and
not as far to the side.
EN-88
LED Indicator Messages
Message Power LED
(Red)
Power LED
(Green)
Temp LED
(Red)
Lamp LED
(Red)
Standby State
(Input power
cord)
Steady light
Power on
(Warming)
Flashing
0.5 sec off
0.5 sec light
Power on & Lamp
lighting
Steady light
Power off
(Cooling)
Flashing
0.5 sec off
0.5 sec light
Back to Red
steady light when
cooling fan turns
off
Quick Resume
(100 secs)
Flashing
0.25 sec off
0.25 sec light
Error
(Lamp fail)
Flashing Steady light
Error
(Fan fail)
Flashing Flashing
Error
(Over Temp)
Flashing Steady light
Standby State
(Burn in mode)
Flashing
Burnin
(Warming)
Flashing
Burnin
(Cooling)
Flashing
EN-89
Optoma Global Offices
For service or support please contact your local office.
USA
3178 Laurelview Ct.
Fremont, CA 94538, USA 888-289-6786
www.optomausa.com services@optoma.com
Canada
3178 Laurelview Ct.
Fremont, CA 94538, USA 888-289-6786
www.optomausa.com services@optoma.com
Europe
42 Caxton Way, The Watford Business
Park
Watford, Hertfordshire,
WD18 8QZ, UK +44 (0) 1923 691 800
www.optoma.eu +44 (0) 1923 691 888
Service Tel : +44 (0)1923 691865 service@tsc-europe.com
France
Batiment E +33 1 41 46 12 20
81-83 avenue Edouard Vaillant +33 1 41 46 94 35
92100 Boulogne Billancourt, France savoptoma@optoma.fr
Spain
C/ Jose Hierro,36 Of. 1C +34 91 499 06 06
28522 Rivas VaciaMadrid, +34 91 670 08 32
Spain
Deutschland
Wiesenstrasse 21 W +49 (0) 211 506 6670
D40549 Dusseldorf, +49 (0) 211 506 66799
Germany info@optoma.de
EN-90
Scandinavia
Lerpeveien 25 +47 32 98 89 90
3040 Drammen +47 32 98 89 99
Norway info@optoma.no
PO.BOX 9515
3038 Drammen
Norway
Latin America
3178 Laurelview Ct.
Fremont, CA 94538, USA 888-289-6786
www.optoma.com.br www.optoma.com.mx
Korea
WOOMI TECH.CO.,LTD.
4F,Minu Bldg.33-14, Kangnam-Ku, +82+2+34430004
seoul,135-815, KOREA +82+2+34430005
Japan
東京都足立区綾瀬 3-25-18
株式会社オーエス
info@os-worldwide.com
コンタクトセンタ:0120-380-495
www.os-worldwide.com
Taiwan
12F., No.215, Sec. 3, Beixin Rd., +886-2-8911-8600
Xindian Dist., New Taipei City 231, +886-2-8911-6550
Taiwan, R.O.C. services@optoma.com.tw
www.optoma.com.tw asia.optoma.com
Hong Kong
Unit A, 27/F Dragon Centre,
79 Wing Hong Street, +852-2396-8968
Cheung Sha Wan, +852-2370-1222
Kowloon, Hong Kong www.optoma.com.hk
EN-91
中国
上海市长宁区
+86-21-62947376
凯旋路 1205 5
+86-21-62947375
琉璃奥图码
www.optoma.com.cn
EN-92
Regulation & Safety Notices
This appendix lists the general notices of your projector.
FCC Notice
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, detectable by turning the equipment in question off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna
Increase the distance between the equipment and the receiver
Connect the equipment to an outlet on a different circuit than that which
the receiver is connected to
Or consult the dealer or an experienced radio/TV technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded
cables to maintain compliance with FCC regulations.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the users authority, which is granted by the Federal Communications
Commission, to operate this projector.
EN-93
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Remarque ą l'intention des utilisateurs canadiens
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
EMC Directive 2004/108/EC (including amendments)
Low Voltage Directive 2006/95/EC
R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device
into the trash when discarding. To
minimize pollution and ensure
utmost protection of the global
environment, please recycle it.
92


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Optoma X501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Optoma X501 in the language / languages: English as an attachment in your email.

The manual is 7,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Optoma X501

Optoma X501 User Manual - German - 94 pages

Optoma X501 User Manual - Dutch - 93 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info