492719
23
Zoom out
Zoom in
Previous page
1/30
Next page
© Calibre UK Limited Issue 1.30 27 January 2012, W: www.calibreuk.com
T:+44 1274 394125 F: +44 1274 730960 E: techsupport@calibreuk..com 19
3.9.5. Switching Transition
When switching input channels by default the last frame of the prior displayed image is frozen and
displayed until a stable image of the new input channel can be shown. The switchover process is
supposed to be as seamless as possible. The source and monitor add switching noise due to
unforeseeable activity of the firmware in said devices. By default HQView is in auto frame rate switching
and I/O lock mode. In order to get a best smooth switching result with the source and monitor I/O lock
and auto frame rate switching have to be switched off in the Output/Display Type menu.
The switching transition of HQView can be set to Freeze, Blank, Fast Fade and Slow Fade. Freeze halts
the prior channel image until the new channel image is stable. Blank switches the output to show a
black screen instead of the last channel image. Fast and slow fade have the prior channel image faded
out and fade into the new channel video image once it is stable.
3.9.6. Menu Settings
This menu provides items to change the menu position and menu display time, i.e. the time after which
the OSD is switched off again with no user interaction. OSD Messages can be activated and
deactivated.
The menu language can be altered and the keypad can be locked. To unlock the keypad a combination
of keys has to be pressed at the same time. The locking of the keyboard is accompanied by the
message: Keypad is locked. Press Up/Down to unlock. When successfully unlocking the keypad the
message shows up: Keypad unlocked.
3.9.7. Network Settings
The Network Settings menu allows to configure the HQView-3xx TCP/IP address for communication
with e.g the warp generator PC tool. Under Address Type a static or DHCP leased address can be
chosen. The static address and Netmask need to be entered manually.
The Network Settings menu has a section with information on the DHCP Status and IP address
assigned to the board, as well as the fixed MAC Address programmed into the HQView-3xx. The DHCP
status is Off when static assignment is used or it displays an address when DHCP has leased an
address accordingly or it is None assigned if the lease was not successful.
Note: When changing from DHCP to Static mode or vice versa it is strongly recommended that
HQView-3xx is powered down after such a change, then powered back up, so that it is properly
recognised by other devices on the network.
In the Network Settings menu is a submenu Status Announce Setting. This feature is activated when
Enable Status Announce is switched on. HQView-3xx will then send messages out continuously through
RS232 and TCP/IP to signal system condition. Server address and port of the PC where to send the
message need to be entered. The Refresh Rate determines the rate at which the HQView-3xx status
condition and the message entered under Custom Data being sent out.
3.9.8. Factory Defaults
This button let you restore all settings to the default values of the HQView-3xx, thus, provide a means to
get back to a known (good) system state. A requestor will come up and ask to confirm prior to actual
restore.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Optoma HQView-300 Series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Optoma HQView-300 Series in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info